Home Monitoring Wireless Color Camera with Receiver User Manual www.jascoproducts.com 1-800-654-8483 45260 rev.
Thank you for purchasing the GE Wireless Color Camera System with Receiver. Please review these instructions carefully before attempting to operate the unit. PRODUCT FEATURES • Wireless system won’t interfere with wireless networks or cordless telephones • View up to two cameras automatically • Audio Detection & Notification feature—alerts when sound is detected in a monitored area • Night Vision feature for low or no light viewing up to 10 ft.
PACKAGE CONTENTS Please check and identify all the parts before proceeding with the installation. 1. Wireless Color Camera 2. Wireless Receiver 3. Wall plate and mounting hardware for camera 4. 2 AC adapters 5. AV cable BEFORE YOU INSTALL When choosing the best location for the placement of the camera and receiver, it is best to avoid any sources of possible RF interference such as microwave ovens and cordless phones.
CHOOSING A CAMERA MOUNTING LOCATION The Wireless Color Camera can be positioned on a tabletop, or mounted to a wall. It is suitable for indoor or outdoor use (use in a protected location). When choosing a mounting location, please be advised: • Do not use in wet locations. If using outside, position camera in a sheltered location. • Do not position the camera so that it points directly into the sun or any bright light, as this may cause damage to the camera.
Customer Service at 800-654-8483. • The Camera has an unobstructed wireless transmission range up to 200 ft. from the receiver. Transmission distance indoors is reduced due to interior walls, wiring, household fixtures and metal plumbing. CONNECTING TO A TV OR MONITOR To prepare for installation of the system, we recommend that you temporarily connect the Receiver to a TV or Monitor to help you choose the best location for installing the camera.
This system will accommodate up to 2 cameras. 1. Connect one end of the cable (3.5mm male) to the rear of the receiver, and the other end (white/yellow) to your television’s A/V inputs. Match the yellow plug to the yellow VIDEO IN jack and the white plug to the white AUDIO IN jack. 2. Plug the AC adapter into the power jack (marked on the back of the receiver, then into an AC outlet. 3. Rotate the antenna to a vertical position. Do not over-tighten. Place the receiver either on top or near to your TV. 4.
active camera, that video will appear on the monitor/ TV screen. Each camera must be assigned to a specific channel; both cameras cannot be on the same channel or the signals will cancel out. 1 2 1 2 1 2 1/2 RECEIVER Channel Setting CAMERA 1 Channel Setting CAMERA 2 Channel Setting Multi-Camera Operation This wireless surveillance system is designed to work with up to 2 cameras. Additional cameras are sold separately.
Auto Mode (2 Camera Operation) To have the receiver automatically switch between two active channels, first check the receiver is set to 1/2 position. Next, press the AUTO button on the top panel of the receiver. The green LED will light and the receiver will automatically select between the two active cameras. The monitor will display images from both cameras alternately. Cycle Time Setting (Time interval between camera selections) The default cycle time for the receiver is preset to 4 seconds.
Night Vision will appear as a Black and White image. When the image sensor detects enough light, color will return to the images. Infra-Red (IR) LEDs Sensor AUDIO DETECTION AND NOTIFICATION FEATURE This feature allows the system to emit an audio alert whenever sound is detected within a Sensitivity monitored area. Control Wheel When the camera detects a sound, the receiver will sound an alert and a notification light will flash.
Desktop Mount: 1. Place camera in desired location on a flat surface. 2. Set Channel switch on camera to 1 or 2. 3. Power ON the TV/monitor; reconnect AC adapter to the camera. 4. Select the channel (1 or 2) on the receiver that corresponds to the camera channel setting. (See Channel Selection) 5. Adjust antenna and camera angle as needed for the clearest picture. Positioning MAX y the antenna upwards to improve sensitivity, and sensitivit downwards to reduce sensitivity.
plate to the wall. Do not run the adapter cable in walls; when securing the cable, do not cut or puncture. 3. Set Channel switch on camera to 1 or 2. Slide the camera onto the alignment and locking pins of the mounting plate. Plug in AC adapter into camera. 4. Adjust antenna and camera angle as needed for the clearest picture. USING THE WIRELESS COLOR CAMERA SYSTEM WITH A VCR or DVR You can connect the camera system to a VCR or DVR in order to record the images received from up to 2 cameras.
TV Power Audio Video In Video Audio In Audio Video In In VCR Power Yellow White Audio Video Out Out Shown with optional rechargeable battery (Sold separately) OPTIONAL WIRELESS BATTERY PACK AVAILABLE (SOLD SEPARATELY) A Rechargeable Battery is available for use with the 45233 Wireless Color Camera. adapter This 850mAh battery will AC charges the power the camera battery for approximately 5 Wall or hours on a single charge. desktop mount To order this battery, please visit www.jascoproducts.
TROUBLE SHOOTING If you are having trouble operating this product, please consult the guide below. If you have any questions or feel the camera system is not operating correctly, or you simply need additional information, please visit our web site www.jascoproducts.com, or contact our Technical Support Group 1-800-654-8483. No camera picture 1. Check all connectors. Make sure camera(s) and receiver are powered ON. 2. Ensure camera(s) and receiver are set to correct channel(s). 3.
Interference on camera picture 1. Make sure each camera (transmitter) is within range, and that no large obstructions are blocking the signal. 2. Try repositioning the camera, receiver or both to improve the reception quality. 3. If a camera is positioned close to the receiver point antenna away from the receiver. 4. Reposition other nearby equipment transmitting on the 900MHz frequency. 5. Adjust the antenna for the camera, receiver or both to obtain best image. Audio problems 1.
High-Speed Electronic Shutter.............................1/60 - 1/15,000 sec Image Sensor................................................................................... 1/3” CMOS Min. Illumination.......................... 0 lux up to 3 feet, 0.5lux up to 10 ft Voltage............................................................................................................9VDC Current Consumption...................................................150mA maximum Overall Size..........................
FCC STATEMENT This device complies with part 15 of the FCC rules. Operation Risk of fire and shock • Only use the supplied cUL listed AC to DC adapter. is subject to the following two • The supplied adapter is for indoor use only. • Do not run the camera cable inside walls; when securing the conditions: cable, do not cut or puncture (1) This device may not cause • Do not use in wet locations harmful interference.
