User Manual
Contents Parts Of The Camera...................................................4 Power Supply...............................................................4 Inserting Storage Media...............................................5 Basic Operation ...........................................................6 Take Photos,Record Video,Playback.........................13 Aligning the camera ..................................................14 Using the wall bracket................................................
Introduction Congratulations on the purchase of your new device. You have selected a high-quality product. The operating instruction is one constituent of this product. It contains important information about safety, use and disposal. Before using the product, familiarise yourself with all operating and safety instructions. Use this product only as described and only for the specified areas of application. Copyright This documentation is subject to copyright protection.
improper use, incompetent repairs, making unauthorised modifications or for using unapproved replacement parts. The operator alone bears liability. When the equipment will be placed in the outdoor filming, rapid changes in the weather could lead to error record. Safety Please read below safety precautions carefully before using the camera. · Do not try to disassemble the product case.Only authorized technician can repair the product. · The camera will be hot after using for too long time.This is normal.
¾ Parts Of The Camera 1.Display Screen 2.Up/Video Button 3.Shot Button 4.Right Button 5.OK Button 6.Speaker 7.Menu Button 8.Left Button 9.Playback Button 10.Down/Photo Button 11.Micro SD Card Slot 12.AV Jack 13.USB Jack 14.OFF-TEST-ON Mode Button 15.Infrared LEDs 16.Lens 17.Front Motion Sensor 18.Side Motion Sensor ¾ Power Supply Please install batteries before using the camera. ♦ Open the camera case and remove the battery cover.
Install 8 pieces of 1.5V AA batteries. Please make sure the electrode is correct. ♦ If the camera is in low power, please connect the camera to a power adapter(not provide) for power supply (The specification of the adapter is DC6.0V/2A). Locate the rubber seal on the bottom of the camera and open it. Connect one end of the power adapter to the hunting machine, and the other end to the power source for power supply.
♦ Do not insert the memory card forcibly. Please refer to the marking on the camera. ♦ For the first time use, please wait for the memory card temperature reach the ambient temperature.The camera will be short-circuit influenced by environment temperature and humidity. Please notice protection for the camera when using it outdoor. ♦ If the capacity of memory card is full,the camera will stop recording automatically and the LEDs will go out. ♦ Press the edge of the card gently to pop-up the TF card.
4. Press Up/Down button to scan all options. And press OK button to confirm options. 5. Press Menu button again to turn back to last menu or exit the setup menu. Setup menu and functions are as below: Mode Set the working mode. In photo mode,the camera just take pictures. In Video mode,the camera just record video. In photo&video mode,the camera will take a photo first,then start to record video. Options:【Photo】/【Video】/【Photo&Video】. Photo Resolution Set the still image resolution.
Video Resolution Set the video resolution. The bigger the resolution is ,the longer the video time can be stored. Options:【3840x2160P】/【2688x1520P 20fps】/ 【1920x1080P】/【1280x720P】/【1280x720P 60fps】 / 848x480P】【 / 720x480P】【 / 640x480P】【 / 320x240P】 . 【 TL Video Resolution Set the resolution of time lapse video . Options:【5200x3900P】 / / 【4608x3456P】 【4416x3312P】 /【4000x3000P】/【3648x2736P】/【3264x2448P】/ 【3072x2304P】/【2592x1944P】/【2048x1536P】. Video Length Set the duration of recording a video clip.
to store too much same events and save more capacity. Options:5 seconds~60 minutes. Side Motion Sensors Open/close the side motion sensors. Options:【On】/【Off】. Sensitivity Motion Sensors Set the sensitivity of the sensors. Environmental impact is small indoors, you can choose “Low”. In outdoor, choose “Middle”in normal condition. Choose “High”if the environment impact is huge outdoors. The temperature can also influence the sensor sensitivity. “High Sensitivity”applies to mild environment.
Time Lapse In Time lapse menu, there are three options as below. [Normal]: The camera will take pictures automatically as per set time interval. For example,set the interval time to 1 hour, the camera will take a photo each hour. If you want to observe that a plant blooms, the camera will take 24 photos in 24 hours to record the whole process of blooming. [TL Video]: You can set the interval time.The time range is from 1 second to 24 hours.
Endless Capture Set the camera to record video in loop. Options:【On】/【Off】. Time & Date Set the date and time of camera. The date format: dd/mm/yyyy, yyyy/mm/dd,mm/dd/yyyy. The time format: 24h,12h. Press Left/Right button to choose the item.Press Up/Down button to adjust the value. And press OK button to confirm. Options:【Set time&date】/【Time format】/【Date format】. Photo Stamp Stamp the date&time on the photos or not. Options:【Time&date】/【Date】/【Off】.
WIFI SSID Set and change the WIFI name. WIFI Password Set and change the WIFI password. Beep Sound Open/close the button sound. Options:【On】/【Off】. Format Memory Card Formatting the memory card will delete all data permanently. Before using a new memory card or a card that has been used in another device previously ,please format the memory card. Options:【Yes】/【No】. Serial NO. Set the unique serial number for the camera. The number is four digits,each digit ranges from 0 to 9 or A to Z. Options:【On】/【Off】.
Version Look up the Firmware information of the camera. ¾ Take Photos,Record Video,Playback Switch the Mode Button to “Test”. In this mode,you can take photos, record video and playback files manually. ♦ Take Photos:Press Photo button to switch to photo mode. Press Shot button to take a picture. ♦ Record Video:Press Video button to switch to video mode.Press Shot button to start to record a video clip. Press Shot button again to stop recording.
/ Unlock current file】【 / Unlock 【Write-protect all files】【 all files】. Aligning the camera In test mode you can adjust the optimum exposure angle and the range of the motion sensors.During alignment, consider whether the use of the side motion sensors may be useful for attaining the desired observation results. You can activate/deactivate the side motion sensors using the above-described menu. Please adjust the camera as follows: 1.
begins to operate independently and enter standby mode. If the wild animals enter the detection range of the motion sensors , the camera will be activated and detect the motion trail. If the wild animals continue to move to the detection zone of the sensor, the camera will take photos or record video automatically. When the wild animals leave the detection zone of the sensors , the camera will be deactivated and turn back to standby mode.
Mounting the wall bracket Required tools ■ Drill ■ 6 mm masonry/concrete drill bit ■ Phillips head screwdriver CAUTION ► Ensure that there are no electric lines, water or heating pipes installed at the proposed drilling location. ► The supplied wall plugs are only suitable for mounting on concrete and stone. Before starting the installation, please check your installation location carefully for its suitability for the plugs. The assembly material used must be suitable for the respective location.
♦ Turn the camera in the desired direction and lock it with the lock nut . ♦ To move the camera into its final position, undo the two pivot bolts a little, position the camera and fix the position by tightening the two pivot bolts . ¾ Remote Control by Mobile App/ Wi-Fi Connecting This camera can be remotely operated almost full functions via a Pad and Smartphone.
4. Open the "Trail Cam Pro" APP and click the "Connect Bluetooth" button on the APP a new interface will pop up, please click "Step One Bluetooth On Wifi" will jump to the Bluetooth list, find the Bluetooth hotspot of Trail Cam Pro and click to select. There will be a prompt "Send Bluetooth command to turn on WIFI..." "WIFI is turned on, please connect" and the phone WIFI option will automatically pop up.
5. After WIFI connection is successful, turn back to APP interface, user can do functional operation in the APP. Power-off Memory card button Setting button Information review button Camera Phone album About Memory card button Click memory card button, user will see below interface shown the photo and video files stored in the TF card.
files,you also can select all. Setting button Click Setting button, user will see below interface shown the setup menu list of camera. Can set the parameters of camera on APP.
Information review button Click information review button, user will see below interface shown the information of camera storage,number of files and battery. User also can see a current image viewed by camera. Click the refresh icon, can refresh image and store the current image in the phone album. Phone album User can review the photo and video files downloaded in the pad or smartphone album. Can zoom in image, playback,choose, delete and share files. 6.
the phone and the camera is closer, the WIFI signal will be stronger, the stability will be better, and the download speed will be faster; 2. After the operation of the APP, it is suggested to click the Power- off button in the upper right corner to shut down the APP. The camera will enter the sleep-hunting mode to save battery power; 3. When the product enters WIFI mode, if the mobile phone fails to connect WIFI after 3 minutes, the product will automatically enter sleep-hunting mode; 4.
4. Once connection is successful,the camera will enter playback mode and the screen turn black. The image will show on the TV. ¾ Download Files To The Computer There are two ways to download files from the memory card to a computer: By inserting the memory card into a card reader By connecting the camera to a computer using the supplied USB cable. Using a Card Reader 1. Pop-up the memory card from the camera and insert it into a card reader.Then connect the card reader to a computer. 2.
2. Open [My Computer] or [Windows Explorer]. A"Removable Disk" appears in the drive list. Double-click the "Removable Disk" icon to view its contents. All files are stored in the folder named ”DCIM”. 3. Copy the photos or files to your computer.
FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.