User Manual
Introduction Congratulations on the purchase of your new device. You have selected a high-quality product. The operating instruction is one constituent of this product. It contains important information about safety, use and disposal. Before using the product, familiarise yourself with all operating and safety instructions. Use this product only as described and only for the specified areas of application. Copyright This documentation is subject to copyright protection.
intended for any other use or for uses extending beyond those stated. This device is notintended for use in commercial or industrial environments. The manufacturer accepts no responsibility for damage caused by failure to observe these instructions, improper use, incompetent repairs, making unauthorised modifications or for using unapproved replacement parts. The operator alone bears liability. When the equipment will be placed in the outdoor filming, rapid changes in the weather could lead to error record.
Parts Of The Camera 1.Display Screen 2.Up/Video Button 3.Shot Button 4.Right Button 5.OK Button 6.Speaker 7.Menu Button 8.Left Button 9.Playback Button 10.Down/Photo Button 11.Micro SD Card Slot 12.AV Jack 13.USB Jack 14.OFF-TEST-ON Mode Button 15.Infrared LEDs 16.Lens 17.Front Motion Sensor 18.
Power Supply Please install batteries before using the camera. ♦ Open the camera case and remove the battery cover. Install 8 pieces of 1.5V AA batteries. Please make sure the electrode is correct. ♦ If the camera is in low power, please connect the camera to a power adapter(not provide) for power supply. Inserting Storage Media Please prepare a Micro SD card and insert it into the camera for saving more files. Before recording, please format the memory card first. ♦ Support Micro SD card,up to 256GB.
♦ For the first time use, please wait for the memory card temperature reach the ambient temperature.The camera will be short-circuit influenced by environment temperature and humidity. Please notice protection for the camera when using it outdoor. ♦ If the capacity of memory card is full,the camera will stop recording automatically and the LEDs will go out. ♦ Press the edge of the card gently to pop-up the TF card.
1. Press Video/Photo button to switch between these two modes. 2. Press Menu button to open the setup menu. 3. Press Up/Down button to scan all menu. Then press OK button to enter the options interface. 4. Press Up/Down button to scan all options. And press OK button to confirm options. 5. Press Menu button again to turn back to last menu or exit the setup menu. Setup menu and functions are as below: Mode Set the working mode. In capture mode,the camera just take pictures.
Options:【20MP(5200x3900P)】/【16MP(4608x3456P)】 /【12MP(4000x3000P)】/【8MP(3264x2448P)】/ 【5MP(2592x1944P)】/【3MP(2048x1536P)】/ 【1MP(1280x960P)】. Photo Series Set the photo number of continuous shooting. In photo mode, the camera will take photos continuously. Options:【1 photo】/【2 photos in series】/【3 photos in series】/【10 photos in series】. Video Resolution Set the video resolution. The bigger the resolution is ,the longer the video time can be stored.
Options:【5200x3900P】/【4608x3456P】/【4416x3312P】 /【4000x3000P】/【3648x2736P】/【3264x2448P】/ 【3072x2304P】/【2592x1944P】/【2048x1536P】. Video Length Set the duration of recording a video clip. The shortest time is 3 seconds and the longest time is 10 minutes. Options:3 seconds~10 minutes. Audio Recording Open this function,the camera will record audio when recording video. Options:【On】/【Off】. Shot Lag Set the time of delay shooting when the camera detects the motion.
IR Distance Set the distance of infrared induction. Options:【Near】/【Middle】/【Far】. Side Motion Sensors Open/close the side motion sensors. Options:【On】/【Off】. Sensitivity Motion Sensors Set the sensitivity of the sensors. Environmental impact is small indoors, you can choose “Low”. In outdoor, choose “Middle”in normal condition. Choose “High” if the environment impact is huge outdoors. The temperature can also influence the sensor sensitivity. “High Sensitivity”applies to mild environment.
will work just in the stated time slot. In other time, the camera will keep in standby state. Options:【On】/【Off】. Set Target recording time 1 Start: Stop: Hr:Min Hr:Min 00 00 00 00 MENU Back OK Select Target Recording Time 2 Set the target recording time 2. As shown in below picture, you can set the second start and stop time.Options:【On】/【Off】.
Time Lapse In Time lapse menu, there are three options as below. [Normal]: The camera will take pictures automatically as per set time interval. For example,set the interval time to 1 hour, the camera will take a photo each hour. If you want to observe that a plant blooms, the camera will take 24 photos in 24 hours to record the whole process of blooming. [TL Video]: You can set the interval time.The time range is from 1 second to 24 hours.
[Off]: Close the time lapse function. Language Set the language display on screen. Options:【English】/【German】/【Danish】/【Finnish】 /【Swedish】【Spanish】/【French】/【Italian】/【Dutch】 /【Portuguese】/【Simplified Chinese】/【Traditional Chinese】/【Japanese】. Endless Capture Set the camera to record video in loop. Options:【On】/【Off】. Time & Date Set the date and time of camera. The date format: dd/mm/yyyy, yyyy/mm/dd,mm/dd/yyyy. The time format: 24h,12h. Press Left/Right button to choose the item.
Photo Stamp Stamp the date&time on the photos or not. Options:【Time&date】/【Date】/【Off】. Password Protection Set the power-on password of the camera. The password is four digits, each digit ranges from 0 to 9 or A to Z. If you forget the password, please reset the camera. Then all parameters will reset to the factory settings. Options:【On】/【Off】. Beep Sound Open/close the button sound. Options:【On】/【Off】. Format Memory Card Formatting the memory card will delete all data permanently.
Options:【Yes】/【No】. Serial NO. Set the unique serial number for the camera. The number is four digits,each digit ranges from 0 to 9 or A to Z. Options:【On】/【Off】. Reset Settings Restore the camera to factory default settings including password,serial number and so on. All settings will be deleted. Options:【Yes】/【No】. Version Look up the Firmware information of the camera. Take Photos,Record Video,Playback Switch the Mode Button to “Test”.
♦ Record Video:Press Video button to switch to video mode.Press Shot button to start to record a video clip. Press Shot button again to stop recording. ♦ Playback:Press Playback button to enter the playback interface. Press Up/Down button to scan photos or video. When playback video, press OK button to play the video. Press OK button again to have a pause. Press Menu button to stop playback. Press Playback button again to exit the playback mode.
Aligning the camera In test mode you can adjust the optimum exposure angle and the range of the motion sensors .During alignment, consider whether the use of the side motion sensors may be useful for attaining the desired observation results. You can activate/deactivate the side motion sensors using the above-described menu. Please adjust the camera as follows: 1. Fasten the camera to a tree or similar object at a height of 1–2 meters and align the camera in the desired direction.
Working Mode Switch the Mode Button to “On”. After turn on the camera,the screen will display 15 seconds countdown. Then the LEDs and screen will go out. The camera begins to operate independently and enter standby mode. If the wild animals enter the detection range of the motion sensors , the camera will be activated and detect the motion trail. If the wild animals continue to move to the detection zone of the sensor, the camera will take photos or record video automatically.
distance about 3m to 20m without overexposing the at night. However, reflective objects such as traffic signs can cause overexposure if they are located within the recording range. In night mode,the pictures just can display white and black. When record a video for long time in the evening, the low voltage may have a great influence on the stability of the machine. Do not record video with low voltage in the evening.
3. Pivot bolts 4. Drill holes 5. Hexagonal screw 6. Wall plugs 7. Screws Mounting the wall bracket Required tools ■ Drill ■ 6 mm masonry/concrete drill bit ■ Phillips head screwdriver CAUTION ► Ensure that there are no electric lines, water or heating pipes installed at the proposed drilling location. ► The supplied wall plugs are only suitable for mounting on concrete and stone. Before starting the installation, please check your installation location carefully for its suitability for the plugs.
Install Steps ♦ Mark the drill holes by holding the foot of the wall bracket at the desired mounting location and marking the hole positions. ♦ Use a drill with a 6 mm drill bit to drill the required holes and insert the plugs and insert the wall plugs flush with the wall. ♦ Screw the wall bracket to the wall using the supplied screws . ♦ Mount the camera on the tripod screw and screw the camera a little way on (about three turns). ♦ Turn the camera in the desired direction and lock it with the lock nut .
Remote Control by Mobile App/ Wi-Fi Connecting This camera can be remotely operated almost full functions via a Pad and Smartphone. Before perform remote control of this camera, an APP named “Trail Cam” should be downloaded from “Apple App Store” or from “Google Play Store” and installed to your Pad and/or Smartphone. Connect of Camera and Pad/Smartphone via WiFi 1. Switch the camera button from "OFF" to "ON". 2. After the 15 seconds countdown finishing, the camera enter sleep working mode.
list will pop-up. Or open the WiFi connection interface on your smartphone, find account “Trail Cam X XXXXX”, enter initial password ”12345678” to connect the WiFi. 5. After WIFI connection is successful, turn back to APP interface, user can do functional operation in the APP.
Memory card button Click memory card button, user will see below interface shown the photo and video files stored in the TF card. Click the icon choose on the top right corner, then can , download and delete choose download delete files 23 the files.
download file to smartphone Setting button Click setting button, user will see below interface shown the setup menu list of camera. Can set the parameters of camera on APP.
Information review button Click information review button, user will see below interface shown the information of camera storage,number of files and battery. User also can see a current image viewed by camera. Click the refresh icon, can refresh image and store the current image in the phone album. Phone album User can review the photo and video files downloaded in the pad or smartphone album.
playback,choose, delete and share files. Operating guidelines Check the APP version and user can view the operating guidelines.
6. After setting finished in APP, turn back to the APP main interface. Click the power-off icon on the top right corner or exit the APP. Hold and press “OFF” button on the remote control for 3 seconds, the camera will enter sleep working mode. Connecting To TV The camera can transfer the video signal to an external monitor or a television. Please follow below instructions to operate. 1. Connect the camera to the TV via provided AV cable. 2. Turn on the TV and set it to AV mode. 3.
Download Files To The Computer There are two ways to download files from the memory card to a computer: By inserting the memory card into a card reader By connecting the camera to a computer using the supplied USB cable. Using a Card Reader 1. Pop-up the memory card from the camera and insert it into a card reader.Then connect the card reader to a computer. 2. Open [My Computer] or [Windows Explorer] and double-click the removable disk icon that represents the memory card. 3.
the "Removable Disk" icon to view its contents. All files are stored in the folder named ”DCIM”. 3. Copy the photos or files to your computer.
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.