43202-22 BROWN 43202-32 SLATE 10’x12’ GAZEBO ASSEMBLY INSTRUCTIONS DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED PLEASE VERIFY THE CONTENT OF EACH BOX AGAINST THE LIST OF PARTS Assembly With More Than One Person Recommended Base Dimensions 11’ 3” x 8’ 9” Largest Dimensions 9’9” x 11’11” Overall Height 108.5’’ ZZZ-202.43202.0114-21.GP.EN.doc WEB VERSION APPROX.
DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED PLEASE VERIFY THE CONTENT OF EACH BOX AGAINST THE LIST OF PARTS 10ft x 12ft / 3.048m x 3.66m GAZEBO Instruction Manual IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY Consult with your local governing authority / local municipal codes regarding installation of temporary structures before purchase or assembly. Some jurisdictions may require permits for, or otherwise regulate, installation and use.
MAINTENANCE NOTES 1. In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly. 2. Please have the parts list and part numbers on hand when ordering or requesting replacement parts. 3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the roof and cause it to collapse. 4. While the product is designed to stay assembled year long, the roof must be kept free of accumulation of snow.
Before You Assemble the Gazebo PLEASE DON'T DESTROY BOXES UNTIL COMPLETELY ASSEMBLED Please verify the content of each box against the list of parts. It is important that this gazebo be anchored on a solid base with the provided screws. Otherwise, please ensure that you use anchors sufficient for your surface. The gazebo should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the gazebo and cause it to collapse.
ZZZ-202.43202.0114-21.GP.EN.
Step 2: For each leg “G”, attach foot plate “H” using 3 bolts “Pp”. Step 3: 1. Unscrew 4 Pp Bolts as shown below, have someone lift the Beam assembly and attach each Leg “G” into a Corner, again securing each using 4 Bolts “Pp”. 2. Repeat until all four Legs are in place. ZZZ-202.43202.0114-21.GP.EN.
Step 4: 1. Install Middle Cover “J” at each of the 4 beam junctions, using 4 Screws “Qq” each. 2. Install Corner Cover “I” at each of the corners, using 4 Screws “Qq” each. ZZZ-202.43202.0114-21.GP.EN.
Step 5: 1. Attach Mounting Brackets “O” and “P” to Rafters “M” and “N” respectively. Use threaded hole about 8 ½” & 5” from end of rafter. 2. Lift Central Hub “L” to a height of about 110” (2.79m) at the center of the gazebo. (Caution: this part may be heavy, use support as needed) 3. Attach one end of Rafter “M” to the hub using 2 Bolt “Pp”. Attach other end with Mounting Bracket to the corner of the beam assembly with 2 Bolts “Pp”. Use the set of holes closest to the inside.
Step 7: 1. Install the flashings “Q”, “R”, and “S” onto the beam assembly, using screws “Qq” on the inside. The notched end of a flashing will always go in a corner of the gazebo. Step 8: 1. Install the curtain rails “T” and “U” on the inside of the beam assembly using bolts “Pp”. Pp ZZZ-202.43202.0114-21.GP.EN.
Step 9: 1. Slide the indicated polycarbonate panels into the spaces between the rafters, using the top groove of each rafter. Ensure the side meant to face the sun is on the outside. Use a rubber hammer to carefully tap each panel into the grooves. Step 10: 1. Insert the middle roof joints in between the rafters and slide them up under the polycarbonate panels. Tap lightly to ensure the panel is fully in the slot.
Step 11: 1. Slide the remaining polycarbonate roof panels in the lower groove of the rafters and into the lower slot of the roof joints. Tap to make sure panels fit securely and do not extend past the ends of the rafters. Step 12: 1. Starting from any end, install all edgings, with end caps “Gg” or “Hh” at each junction or corner espectively. Use bolts “Pp” to secure. ZZZ-202.43202.0114-21.GP.EN.
Step 13: 1. Install the upper crossbars on the interior of the roof using bolts “Pp”, following the shaped ends and letters. Do not tighten bolts immediately; install loose and tighten once all crossbars are in place. 2. Repeat this step with the lower crossbars. Pp Pp Pp Step 14: 1. Secure each foot plate into the ground using screws “Rr” and washers “Tt”. 2. Use lag shields (Ss) if needed for harder surfaces. ZZZ-202.43202.0114-21.GP.EN.
Step 15: Install the screen curtains “Ww” in the interior groove of the curtain rails, using the provided hooks. Install the privacy curtains “Xx” in the exterior groove of the rails. Once the hooks are in, use curtain rail caps “Uu” to close ends of curtain rails. IMPORTANT NOTES: Make sure all screws and bolts are tight. If conditions are windy, you may have to add cable guides at the corners. ZZZ-202.43202.0114-21.GP.EN.
43200 BROWN (see page 17 for Slate parts) PART PACKED IN BOX QTY (11-624-22) DIAGRAM PART 60 3/8” TOP LEFT BEAM A (11-625-22) ROOF RAFTER N (12-030-22) RAFTER M MOUNTING BRACKET O (12-031-22) RAFTER N MOUNTING BRACKET P (11-638-22) 3 2 3 2 3 2 3 2 RIGHT FLASHING Q (11-639-22) 3 4 LEFT FLASHING R (11-640-22) 4 CENTER FLASHING BEAM B (11-626-22) 65 ½” TOP LEFT BEAM C (11-627-22) 65 ½” TOP RIGHT BEAM D (11-628-22) CORNER PLATE E (11-629-22) CENTER PLATE F 2 4 2 6 2 4 2 4 2 2
PART PACKED QTY IN BOX DIAGRAM PART PACKED QTY IN BOX DIAGRAM (11-644-22) (11-633-22) MIDDLE COVER J 29 ½”x25 ½” 3 4 1 2 1 4 2 4 2 2 2 4 4 (08-158-22) BOLT Pp 3 182 4 (08-156-22) SCREW Qq 3 92 4 (08-167-22) SCREW Rr 3 12 (11-634-22) 37 ¼” MIDDLE UPPER ROOF PANEL W (11-645-22) 30”x30” 1 RIGHT UPPER ROOF PANEL X (11-646-22) 34 ¼” 30 ¾” CENTRAL HUB L 1 LEFT MIDDLE ROOF JOINT Y (11-647-22) TOP CAP K 2 (11-635-22) 2 (11-636-22) 25 ½” 83” ROOF RAFTER M 2 4 CENTER
PART PACKED QTY IN BOX DIAGRAM PART PACKED QTY IN BOX DIAGRAM (11-652-22) 26 ¾” CENTER EDGING Ee (11-653-22) 2 2 (08-193-22) PLASTIC PLUG Ss 3 12 4 (08-187-22) WASHER Tt 3 15 6 (11-697-22) CURTAIN RAIL CAP Uu 3 8 4 (08-189-22) ACORN NUT Vv 3 3 4 (11-695-22) SCREEN/MOU STIQUAIRE Ww 58 7/8” RIGHT EDGING Ff (11-654-22) RAFTER CAP Gg (11-655-22) CORNER END BRACKET Hh (11-656-22) 2 2 2 44” LEFT LOWER CROSSBAR Ii (11-657-22) 2 26 ¾” MIDDLE LOWER CROSSBAR Jj (11-658-22) 2 2 (
43200-32 SLATE PART PACKED IN BOX QTY (11-624-32) DIAGRAM PART 60 3/8” TOP LEFT BEAM A (11-625-32) ROOF RAFTER N (12-030-32) RAFTER M MOUNTING BRACKET O (12-031-32) RAFTER N MOUNTING BRACKET P (11-638-32) 3 2 3 2 3 2 3 2 RIGHT FLASHING Q (11-639-32) 3 4 LEFT FLASHING R (11-640-32) 4 CENTER FLASHING BEAM B (11-626-32) 65 ½” TOP LEFT BEAM C (11-627-32) 65 ½” TOP RIGHT BEAM D (11-628-32) CORNER PLATE E (11-629-32) CENTER PLATE F 2 4 2 6 2 4 2 4 2 2 2 4 2 4 1 4 25 3/8”
PART PACKED QTY IN BOX DIAGRAM PART PACKED QTY IN BOX DIAGRAM (11-644-32) (11-633-32) MIDDLE COVER J 29 ½”x25 ½” 3 4 2 1 (11-634-32) 37 ¼” MIDDLE UPPER ROOF PANEL W (11-645-32) (11-635-32) 34 ¼” 30 ¾” CENTRAL HUB L 2 1 (11-636-32) 1 4 LEFT MIDDLE ROOF JOINT Y (11-647-32) 2 4 2 2 2 4 25 ½” 83” ROOF RAFTER M 2 30”x30” RIGHT UPPER ROOF PANEL X (11-646-32) TOP CAP K 1 2 4 CENTER MIDDLE ROOF JOINT Z (11-648-32) 30 ¾” RIGHT MIDDLE ROOF JOINT Aa (11-649-32) (11-661-32) 17
PART PACKED QTY IN BOX DIAGRAM PART PACKED QTY IN BOX DIAGRAM (11-652-32) 26 ¾” CENTER EDGING Ee (11-653-32) 2 2 (08-193-32) PLASTIC PLUG Ss 3 12 4 (08-187-32) WASHER Tt 3 15 6 (11-697-32) CURTAIN RAIL CAP Uu 3 8 4 (08-189-32) ACORN NUT Vv 3 3 4 (11-695-32) SCREEN/MOU STIQUAIRE Ww 58 7/8” RIGHT EDGING Ff (11-654-32) RAFTER CAP Gg (11-655-32) CORNER END BRACKET Hh (11-656-32) 2 2 2 44” LEFT LOWER CROSSBAR Ii (11-657-32) 2 26 ¾” MIDDLE LOWER CROSSBAR Jj (11-658-32) 2 2 (
NOTE: The Dimensions Are Approximate. ZZZ-202.43202.0114-21.GP.EN.