430133 COOLER CART INSTALLATION MANUAL 430133 430133.Cooler Cart.0911-18.GP.
COOLER CART PARTS PART QTY LEFT CART LEG L1 18-093 DIAGRAM PART QTY 1 RUBBER PLUG L 18-103 1 RIGHT CART LEG L2 18-094 1 PLASTIC TUBE M 18-104 1 TOP BOX B 18-095 1 OPEN WRENCH N 18-105 1 SHELF HANDLE S 18-096 2 ALLEN WRENCH O 18-106 1 BOTTOM PANEL P 18-097 1 PLASTIC CLIP C 18-107 4 BOLT M6x18mm F 18-098 16 WHEEL E 18-108 4 BOLT M6x30mm G 18-099 4 DRAIN FASTENER E2 18-109 1 BOLT M6x32mm H 18-100 2 WASHER I 18-110 18 PLASTIC WASHER K 18-101 4 NYLON LOCK NUT J 18-111 4 B
STEP 1 Install the 4 plastic clips (C) on the tablets. 430133.Cooler Cart.0911-18.GP.
STEP 2 Screw legs (L1/L2) to top box (B) with bolts (G, F) and washers (I) using allen wrench (O). 430133.Cooler Cart.0911-18.GP.
STEP 3 Attach shelf handle (S) to the top box (B) using bolt (F), washer (I), plastic washer (K) and nylon lock nut (J). Note: Do not over tighten. 430133.Cooler Cart.0911-18.GP.
STEP 4 Fix the corners of the bottom panel (P) under the brackets of the legs (L1/L2) using bolt (F) and washer (I). STEP 5 Fix the sides of the bottom panel (P) under the brackets of the legs (L1/L2) using bolt (H) and washer (I). Note: This is done from the inside. 430133.Cooler Cart.0911-18.GP.
STEP 6 Install wheels (E) 430133.Cooler Cart.0911-18.GP.
STEP 7 Turn the unit back to its standing position and make sure that the shelve handles are lifted. Lock it to the tray on each side to make it flat. 430133.Cooler Cart.0911-18.GP.
STEP 8 Insert drain tube (M) into the drain fittings (E3, E4) and lock with drain fastener (E2). 430133.Cooler Cart.0911-18.GP.
STEP 9 Insert the rubber plug (L) into the drain hole. 430133.Cooler Cart.0911-18.GP.
STEP 10 Screw bottle opener (A) with bolts (F). 430133.Cooler Cart.0911-18.GP.
STEP 11 Fill it up and enjoy. Note: Keep dry when not in use to prevent rust. If any leakage, use latex by yourself. 430133.Cooler Cart.0911-18.GP.
MAINTENANCE NOTES 1. Please don't destroy the box until completely assembled. 2. The warranty only applies to the original purchaser with the bill. 3. In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly. 4. Please have the parts list and part numbers on hand when ordering or requesting replacement parts.
430133 CHARIOT REFROIDISSEUR GUIDE D’INSTALLATION 430133.Cooler Cart.0911-18.GP.
PIECES DU CHARIOT REFROIDISSEUR PIECES QT DIAGRAMME PIECES QT 1 PATTE GAUCHE L1 18-093 1 CAPUCHON EN PLASTIQUE L 18-103 PATTE DROITE L2 18-094 1 TUBE EN PLASTIQUE M 18-104 1 BOITE SUPERIEURE B 18-095 1 CLE HEXAGONALE N 18-105 1 POIGNÉE DE TABLETTE S 18-096 2 CLE ALLEN O 18-106 1 PANNEAU INFERIEUR P 18-097 1 ATTACHE EN PLASTIQUE C 18-107 4 BOULON M6x18mm F 18-098 16 ROUE E 18-108 4 BOULON M6x28mm G 18-099 4 FERMETURE DE DRAIN E2 18-109 1 BOULON M6x32mm H 18-100 2 RONDELLE I
ÉTAPE 1 Installer les 4 attaches en plastique (C) sur les tablettes. 430133.Cooler Cart.0911-18.GP.
ÉTAPE 2 Vissez les pattes (L1 / L2) dans la boîte supérieure (B) à l'aide de boulons (G, F) et des rondelles (I) à l'aide d'une clé hexagonale (O). 430133.Cooler Cart.0911-18.GP.
ÉTAPE 3 Fixez la poignée de tablette (S) à la boîte supérieure (B) en utilisant le boulon (F), la rondelle (I), la rondelle en plastique (K) et l'écrou de verrouillage en nylon (J). Remarque: Ne pas trop serrer. 430133.Cooler Cart.0911-18.GP.
ÉTAPE 4 Fixez les coins du panneau inférieur (P) sous les supports des jambes (L1/L2) à l'aide du boulon (F) et de la rondelle (I). ÉTAPE 5 Fixez les côtés du panneau inférieur (P) sous les supports des jambes (L1/L2) à l'aide du boulon (H) et de la rondelle (I). Remarque: Cette étape se fait à partir de l'intérieur. 430133.Cooler Cart.0911-18.GP.
ÉTAPE 6 Installer les roues (E). 430133.Cooler Cart.0911-18.GP.
ÉTAPE 7 Insérez le capuchon (L) dans le trou de vidange. 430133.Cooler Cart.0911-18.GP.
ÉTAPE 8 Insérer le tube de drainage (M) dans les raccords de vidange (E3, E4) et le verrouiller avec l’attache de vidange (E2). 430133.Cooler Cart.0911-18.GP.
ÉTAPE 9 Insérez le capuchon (L) dans le trou de vidange. 430133.Cooler Cart.0911-18.GP.
ÉTAPE 10 Vissez l'ouvre-bouteille (A) avec des boulons (F). 430133.Cooler Cart.0911-18.GP.
ÉTAPE 11 Remplissez-le et profitez-en. Remarque: Conserver à sec lorsqu'il n’est pas utilisé afin d’éviter la rouille. En cas de fuite, utilisez du latex. 430133.Cooler Cart.0911-18.GP.
NOTES DE MAINTENANCE 1. Ne détruisez pas les boîtes avant que l'abri soit complètement assemblé. 2. Advenant que le produit soit endommagé ou que la période de garantie soit expirée, veuillez contacter le département de service à la clientèle de Gazebo Penguin afin d’obtenir une liste complète des pièces de remplacement et des prix applicables. 3. Veuillez consulter la liste des pièces et leurs numéros lors de la commande ou de la demande de pièces de rechange.