AG-168V SIP GATEWAY User Manual (V1.42) AG-168V SIP GATEWAY User Manual AG-168V SIP GATEWAY Appearance Introduction: ...................................................... 2 Features ................................................................................................................................ 2 Function Keys of AG-168V SIP GATEWAY Introduction ........................................... 3 Standard and Protocol................................................................
AG-168V SIP GATEWAY User Manual (V1.
AG-168V SIP GATEWAY User Manual (V1.
AG-168V SIP GATEWAY User Manual (V1.42) Dynamic voice jitter buffer G.168/165 compliant 16ms echo cancellation Tone generation and Local DTMF re-generation according with ITU-T E.164 dial plan and customized dial rules 100 entries for quick dial Voice prompt Hotline Standard and Protocol Gateway supports following standard and protocol: IEEE 802.3 /802.3 u 10 Base T / 100Base TX Major G.
AG-168V SIP GATEWAY User Manual (V1.42) Network interface:1 RJ-45 Ethernet Connectors FXS:1 RJ-11 For Tel Line:1 RJ-11 For PSTN Size 150 x 110 x 28 mm (L x W x H) Installation: 1 Connecting to network: connecting one side of the cable to the lan port of AG-168V, the other side to PBX or HUB or ADSL and Cable Modem’s lan port.. 2 Connecting to phone: Insert one side of RJ11 line to the Tel port of AG-168V , the other side to the phones’ interface. Connecting the Line’s port of AG-168V to PSTN line.
AG-168V SIP GATEWAY User Manual (V1.42) Configuration Two different ways can be used to configure AG-168V H323 phone: phone web browser, Telnet commands on computer.
AG-168V SIP GATEWAY User Manual (V1.42) x input the ip address xxx.xxxx.xxx.xxx, press “ip ” button . Using the button + IP of * for , Configured by WEB Double click icon to open the IE browser. Input the IP address of the GATEWAY into address bar ( ), and then input password of the GATEWAY into the following page. Default password 1234 is ordinary password and super password is 12345678.
AG-168V SIP GATEWAY User Manual (V1.42) Fig 3.1 Http Setting Network Setting Fig 3.2 Network Setting iptype: Set how IP GATEWAY gets relevant network parameters by selecting corresponding item from drop down list. static ip: Select this item to authorize users set IP address, subnet mask and router IP address of IP GATEWAY manually. dhcp: Select this item to enable DHCP mode.
AG-168V SIP GATEWAY User Manual (V1.42) relevant network parameters auto. Then please fill ID and pin into ppp id and ppppin fields. ppp id: With pppoe or modem selected in iptype drop down list, please enter the user name here. ppp pin: With pppoe or modem selected in iptype drop down list, please enter the password here. local ip: With static ip selected in iptype drop down list, please enter IP address of IP GATEWAY here.
AG-168V SIP GATEWAY User Manual (V1.42) Protocol Setting Fig 3.3 Protocol Setting use service: Enable/disable service by checking/clearing this box. To make calls through gatekeeper, please check this box; otherwise, GATEWAY can only make IP-to IP calls or calls through gateway. register ttl: IP phone will send a keep-alive registration message to SIP proxy server every “register ttl” seconds. The minimum value is 10, maximum value is 65535. Default is 60.
AG-168V SIP GATEWAY User Manual (V1.42) kaimen use kaimen’s system mediaring: use mediaring’s system italkbb: use italkbb’s system stanaphone: use stanaphone’s system net2phone: use net2phone’s system fwd: use fwd(freeworlddialup) system ipphonex: use ipphonex’s system sipphone: use siphone’s system ngtel: use ngtel’s system ayctel: use AycTe’s system SIP proxy: when user service write SIP Proxy Server URI.
AG-168V SIP GATEWAY User Manual (V1.42) every “nat ttl” seconds to keep the port mapping on the NAT device alive. “nat ttl” is an integer between 10 and 65535 .default value is 20. phone number: set local ID . account: set aaa@bbb format account register. pin: set password. register port: The local UDP port registered with server to accept incoming handshaking messages. Default is 5060 rtp port : RTP port is the port transferring and receiving voice packets using UDP protocol.
AG-168V SIP GATEWAY User Manual (V1.42) recommended way with SIP protocol used. dtmf: Set DTMF signal sending way by selecting control string, inband audio, signal keypad or rfc 2833 ,sip infofrom list box. dtmf payload: set use RTP send DTMF’s RTP the value range is 96-101 register ttl : IP GATEWAY will send a keep-alive registration message to SIP gatekeeper every “register ttl” seconds. The value range is 10-65535. Default is 60. Super password : Set super password.
AG-168V SIP GATEWAY User Manual (V1.42) Fig 3.4 phone Setting use dialplan: Set whether use dial plan or use dial number by selecting the corresponding item in drop down list. disable: Do not use dial plan or dial number by selecting this item. enable: Use dial plan by selecting this item. dialnum: Use dial number by selecting this item. With this item selected, please enter the dial prefix into dial number field. prefix: Use 179XX service by selecting this item.
AG-168V SIP GATEWAY User Manual (V1.42) ddd prefix: With enable or dialnum selected in use dialplan drop down list, set long distance call prefix according to E.164 dial rule, such as 0. inner line: Enable/disable innerline call by selecting corresponding items from dropdown list. disable: Disable call innerline by selecting this item. enable: enable call innerline by selecting this item.
AG-168V SIP GATEWAY User Manual (V1.42) forwarded calls GATEWAY number into fwd number field. fwd busy: Forward calls if busy by checking this box. Please enter receiving forwarded calls GATEWAY number into fwd number field. answer: Enter a number from 0 through 60 to set the entries of the seconds before the GATEWAY answer the call auto or forward the calls. handset in: Drag the slider to adjust the volume of handset input.
AG-168V SIP GATEWAY User Manual (V1.42) g729 g7231 g711u g711a and gsm. codec3: Set the priority 3of the audio compression algorithm. The options are g729 g7231 g711u g711a and gsm. codec4: Set the priority 4of the audio compression algorithm. The options are g729 g7231 g711u g711a and gsm. codec5: Set the priority 5of the audio compression algorithm. The options are g729 g7231 g711u g711a and gsm. g.723.1 high rate: enable/disable g.723.1 high rate. G.723.1 high rate is 6.3kbps, low rate is 5.3kbps.
AG-168V SIP GATEWAY User Manual (V1.42) Phonenumber: check phonenumber auto upgrade. upgrade addr: Put IP address or domain name obtained by ISP of FTP server supplying upgrade program into this field. nts ip: Fill IP address of time server here. use daylight: Enable/disable daylight. timezone: Select correct time zone in list box. When debug set as 0[disable], if input ordinary password (default one is 1234), then following page will pop up after clicking .
AG-168V SIP GATEWAY User Manual (V1.42) button to confirm the modification. phone Book: Click this button to open the speed dial settings page. Please refer to Fig 3.7. In this page, you can set and save the speed dial number by typing the name into the Name field and then entering the corresponding number following the name. For example, input Jack in Name field following 001, and then input 5989426454 into GATEWAY number field. Then Jack’s number 5989426454 is saved in GATEWAY book.
AG-168V SIP GATEWAY User Manual (V1.42) connecting with the GATEWAY or at the same segment of the GATEWAY, double click icon to open the PalmTool. The index page of PalmTool will popup. a) Input the IP address of the GATEWAY into Local IP field (such as 192.168.1.100), and then click “GATEWAY Settings” button. From Version1.24, use PalmTool to set the IP GATEWAY, please set debug as output or output all firstly, or PalmTool cannot connect IP GATEWAY.
AG-168V SIP GATEWAY User Manual (V1.
AG-168V SIP GATEWAY User Manual (V1.42) Syntax description: No optional parameter of keywords Usage: Display basic parameters of the AG-168V IP GATEWAY Relevant usage: None Detailed description: get Display basic running parameters of the AG-168V IP GATEWAY. Input ordinary password without debug being set as 0[disable], or input super password with debug set as 0[disable], then following parameters of IP GATEWAY will be displayed: AG-168V V1.
AG-168V SIP GATEWAY User Manual (V1.42) password 1234 superpassword 19750407 1[output] upgradeaddr [empty] sntpip 0.0.0.0 daylight 0[disable] timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi] debug Input ordinary password with debug set as 0[disable], following information will be seen: AG-168V V1.39 settings Password:**** P:\>get iptype 0[static] ip 192.168.1.100 subnetmask 255.255.255.0 router 192.168.1.254 dns 202.106.196.152 dns2 202.106.196.
AG-168V SIP GATEWAY User Manual (V1.42) address of IP GATEWAY manually; 1: use DHCP mode. With this system, your LAN or router automatically assigns all the required network parameters to any device connected to it when the device log on. AG-168V IP GATEWAY is shipped from the factory with DHCP on.
AG-168V SIP GATEWAY User Manual (V1.42) With iptype set as 0, use this command to set subnet mask of AG-168V IP GATEWAY. set router XXX.XXX.XXX.XXX With iptype set as 0, use this command to set router IP of network with AG-168V IP GATEWAY. set dns XXX.XXX.XXX.XXX With iptype set as 0, use this command to set IP address of DNS server. set dns2 XXX.XXX.XXX.XXX With iptype set as 0, use this command to set IP of backup DNS server. set mac XX-XX-XX-XX-XX-XX Set MAC address of the AG-168V IP GATEWAY.
AG-168V SIP GATEWAY User Manual (V1.42) 17: use Lucent system; 19: use IPN system; 20: use yayuang system; 21: use thinker system; 22: use suntek system; 28: use txtc system. set serviceaddr XXXX Set IP address or domain name of gatekeeper. set serviceid XXXXX Set service ID according to required by service system. set nattraversal X Set NAT traversal or not. X ranged from 0 through 7: 0: do not use.
AG-168V SIP GATEWAY User Manual (V1.42) www.ipchicken.com;www.showmyip.com;www.whatismyip.com; www.myipaddress.com; www.whatismyipaddress.com; ip.sbbs.net; www.whatismyipaddress.net;checkip.dyndns.org set natttl XX Set NAT TTL XX is an integer between 10 and 65535 sec. default value is 20 sec. set GATEWAYnumber XXXXXXXX Set a GATEWAY number of AG-168V IP GATEWAY . Value xxxxx must be an Arabic numeral and no longer than 16 characters.
AG-168V SIP GATEWAY User Manual (V1.42) set registerttl X Set register TTL. X is range from 10 through 65535 Sec. default value is 60 Sec. set rtptos X Set TOS segment of IP head package in RTP digital follow. set rtpport XXXX RTP port is the port transferring and receiving voice flow using UDP protocol. XXXX is range from 1024 through 65535. set jittersize X Set buffer size of RTP package. X is range from 0-32. set calltype X Set call type of the GATEWAY.
AG-168V SIP GATEWAY User Manual (V1.42) Set DTMF relay type. X is ranged form 0 through 3: 0:control string 1:inband audio 2: signal keypad 3:rfc 2833. set dtmf payload X When dtmf X select 3(rfc 2833).This parameter can be used indicating type of RTP payload type. The value can be use integer 96-101. set dialplan X Enable/disable dial plan and dial number. Parameter X ranged from 0 through 4: 0: disable dial plan; 1: enable dial plan; 2: use dial number; 3: use 179XX service.;4: use hotline function.
AG-168V SIP GATEWAY User Manual (V1.42) set iddprefix XX Set IDD service prefix number when set dialplan value set as 1 or 2. For example, IDD service prefix number of china is 00; IDD service prefix number of USA is 1, etc. Parameter xxx must be an Arabic numeral and no longer than 3 characters. set dddprefix XX Set DDD service prefix number when set dialplan value set as 1 or 2. For example, DDD service prefix number of china is 0; DDD service prefix number of USA is 1, etc.
AG-168V SIP GATEWAY User Manual (V1.42) Set types of ring. X is ranged from 0 tohrough 12: 0-9: ring as ordinary rings in different frequency; 10: do not ring; 11: ring as music shipped from factory; 12: ring as music saved by user set digitmap X Set whether to use digitmap. X ranged from 0 to 1: 0: do not use digitmap; 1: use digitmap. set fwdnumber XXXXXXX Set receiving forwarded calls GATEWAY number.
AG-168V SIP GATEWAY User Manual (V1.42) Set audio frames in RTP package. X is Arabic numerals between 0 and 7. set 6.3k X With G.7231, set AG-168V IP GATEWAY to use 6.3K rate or not. X is ranged from 0 through 1: 0: use 6.3K rate; 1: use 5.3K rate. set vad X Enable/disable VAD. X is ranged from 0 through 1: 0: disable VAD; 1: enable VAD. set agc X Enable/disable AGC. X is ranged from 0 through 1: 0: disable AGC; 1: enable AGC. set aec X Enable/disable AEC.
AG-168V SIP GATEWAY User Manual (V1.42) through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm. set codec2 X Set the priority 2 of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm. set codec3 X Set the priority 3 of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm. set codec4 X Set the priority 4of the audio compression algorithm.
AG-168V SIP GATEWAY User Manual (V1.42) set upgradeaddr XXX.XXX.XXX.XXX Set IP address or domain name of FTP server supplying upgraded program of AG-168V IP GATEWAY. set ntsip XXX.XXX.XXX.XXX Set IP address of time server. set daylight X Set use daylight or not. X ranged from 0 through 1: 0: do not use daylight; 1: use daylight. set timezone XX Set time zone. Command store Syntax description: no keyword. Parameter ranged from 0 through 4. Usage: Save the current settings to the designated position.
AG-168V SIP GATEWAY User Manual (V1.42) Syntax description: No keyword and parameter Usage: Save the configuration and restart the AG-168V IP GATEWAY. Command ping Syntax description: ping IP address Usage: ping IP address of other NAT device Relevant usage: In telnet window, input ping xx.xxx.xx.xx an IP address and return, then the result will be displayed. If the address is effective, “ping OK” will be seen; if the address is ineffective, nothing will be seen. Fox example: P:\>ping 203.93.9.
AG-168V SIP GATEWAY User Manual (V1.42) Note All the Telnet commands of AG-168V IP GATEWAY should be written in low case and the password is case sensitive. The usage of AG-168V FXS Receving calls No matter what calls from IP or PSTN , the phone connecting to AG-168V FXS port will ring . Mention you that there is call. You can pick up the handset or the speaker of the normal phone.
AG-168V SIP GATEWAY User Manual (V1.42) and then press . Call when PSTN first Dual mode enabled Call PSTN number When PSTN first setted, the way of dial is the same as normal PSTN phone. Call voip number Press the cradle or the flash key of the normal phone, enable AG-168 to be in voip state from pstn first mode. Dial after the dial tone.
AG-168V SIP GATEWAY User Manual (V1.42) Upgrade AG-168V IP GATEWAY Telnet command to updating Using telnet , connecting AG-168V FXS, input SuperPassword when registered. Input ftp X command to update, the value range is 0-2 . detailed meaning is : x-0 connecting to FTP server, getting the file to updating , and save in the sdram of the phone. Read from palmtool in order to debug.
AG-168V SIP GATEWAY User Manual (V1.42) logins. 2. The service provider needs to upload these files to the FTP server: HardwareTag_ServiceType_Protocol_XXX.bin This file contains the phone’s firmware binary HardwareTag_ServiceType_Protocol_cfgXXX.dat This file contains the phone’s configuration settings HardwareTag_ServiceType_Protocol_mapXXX.
AG-168V SIP GATEWAY User Manual (V1.42) parameter is "disable", "all", "mac", "pppid", "account", "phonenumber". When select as "disable" the terminal will NOT do the auto upgrade when select as "all" then the terminal will do the upgrade as item 2 when select as other value it will add more check based on item 2’s rule. The detail rules are: Mac PA168S_citron_h323_00-09-45-00-00-00_135.bin Ppp id PA168S_citron_h323_pppid_135.bin Account PA168S_citron_h323_account_135.
AG-168V SIP GATEWAY User Manual (V1.42) and there are no new features of use to them in our 1.35 and 1.36 versions, then they don’t need to put these files on FTP server. The customers will continue to use version 1.34. However if we have some useful features in 1.37, then by uploading the new files to the FTP server all customers will be upgraded at their next system reboot. 4. We also support manual FTP upgrades via the keypad on phones.