Quick Setup Guide

PACKAGE CONTENTS
• LED lightstrip
• Remote control
• Screws (2)
• RF controller box
• Double-sided tape
• Cable clips (2)
• Quick Setup Guide
Before using your new product, please read these instructions to prevent any damage.
SETTING UP YOUR LIGHTSTRIP
Shortening your lightstrip
1 Decide how long you need your lightstrip to be. When
measuring, make sure that you start from the side of the
tape that has the controller box connected to it. The part of
2 Locate the nearest cut line, then cut with a pair of scissors.
Cut lines are about 3.9 in. (9.9 cm) apart.
WARNING: Do not cut the silver solder markings. Only cut in the
center of the copper-colored pads, as shown.
Attaching your lights
CAUTION: To avoid damage to the lightstrip, do not sharply twist
or bend the lightstrip 90° or more.
1
lights where you want them.
2 Optional: Attach the double-sided tape to the back of the
RF controller box, then attach it where you want it.
OR
Attach the RF controller box to a surface using the two
included screws.
FEATURES
• 16 selectable colors provide accent or ambient lighting
• 16 ft LED lightstrip can be cut to your ideal length
• Self-adhesive back attaches to TVs, cabinets, or other locations
for custom lighting
• RF remote gives you full control over your lightstrip from a
distance
• Multi-step dimmer adjusts to the brightness level you want
• Connects to included USB wall adapter or any USB port
Lightstrip
Remote control
Notes:
• Make sure that the lightstrip is unrolled, otherwise it can
used if the LED tape detaches from the surface. Small pieces
of clear tape can be used.
Connecting to power
1 Connect the AC adapter plug to the controller box.
2 Connect the controller box to the lightstrip’s 4-pin
connector. Make sure that the arrows on the connectors
are pointing to each other.
3 Plug the AC adapter into a power outlet.
WARNING: Unroll before use. Never plug in the LED lights when
4 Remove the plastic battery-saver tab from the remote
control.
QUICK SETUP GUIDE
16 ft. Full-Color
LED Lightstrip
Final flat size: 17.5 × 5.5 in. (444.5 × 139.7 mm)
Final fold size: 3.5 ×5.5 in. (88.9 × 139.7 mm)
AC adapter
Controller connector
4-pin connector
RF controller box
Cut line
AC adapter
Arrows
Brightness up
Red
Orange
Light orange
Orange white
Yellow
Gradual jump with
3 preset colors
Speed up color
changing
1-hour sleep timer
Reactive music
(classical)
Brightness down
Green
Light green
Light cyan
Cyan
Dark cyan
Gradual jump with
7 preset colors
Slow down color
changing
2-hour sleep timer
Reactive music
(gentle)
Pause/run
Blue
Light blue
Purple
Light purple
Rose pink
Gradual fade with
3 preset colors
4-hour sleep timer
Reactive music
(dynamic)
White light 100%
White light 75%
White light 50%
Sunrise
Sunset
Gradual fade with
7 preset colors
Auto mode
8-hour sleep timer
Reactive music
(disco)
Cut line Cut line
Cut line
REPLACING THE REMOTE CONTROL
BATTERY
1 Squeeze the tab and pull out the battery compartment.
2 Replace with a CR2025 battery, making sure that the + side
is facing up.
3 Reinsert the battery compartment.
[REVIEWERS: Is there a plastic tab in the battery compartment?
Sometimes remotes like this have a plastic tab in there (for protection
I assume). If so, it needs to be removed (can cause the remote not to
work).]
WARNING: Unroll before use. Never plug in the LED
lights when rolled up, as this can result in product
4
8
w
57
%
50
%
4
8
w
75%
50%
4
8
w
57
%
50
%
GW: Yes, there is have plastic tab,it for coin to
leakage protection,remove it when you need it to work
and insert when it's not work.