owner’s manual EDGE® 500 GPS-ENABLED CYCLING COMPUTER
© 2009–2013 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Tel. (913) 397.8200 or (800) 800.1020 Fax (913) 397.8282 Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK Tel. +44 (0) 870.8501241 (outside the UK) 0808 2380000 (within the UK) Fax +44 (0) 870.8501251 All rights reserved.
Table of Contents Getting Started..................... 1 About the Battery........................ 1 Installing the Edge...................... 2 Turning on the Edge................... 4 Acquiring Satellite Signals.......... 6 Optional ANT+ Sensors.............. 6 Going for a Ride......................... 7 Saving Your Ride Data............... 7 Using Garmin Connect............... 7 Transferring History to Your Computer ................................ 8 Training with Your Edge...... 9 Alerts.............
Data Management.............. 34 Connecting the USB Cable ..... 34 Loading Files............................ 34 Deleting Files............................ 35 Settings.............................. 36 Customizing Your Data Fields.. 36 Data Fields............................... 37 Changing Your System Settings.................................. 40 Changing Your User Profile Settings.................................. 42 Updating Your Bike Profile........ 42 Switching Bikes........................
Getting Started Getting Started warning Always consult your physician before you begin or modify any exercise program. See the Important Safety and Product Information guide in the product box for product warnings and other important information. When using your Edge® the first time, complete the following tasks: 1. 2. 3. 4. 5. Charge the Edge (page 2). Install the Edge (page 2). Turn on the Edge (page 4). Acquire satellites (page 6). Set up optional ANT+™ sensors (page 6). 6.
Getting Started Charging the Edge notice To prevent corrosion, thoroughly dry the mini-USB port, the weather cap, and the surrounding area before charging or connecting to a computer. 1. Plug the AC charger into a standard wall outlet. 2. Pull up the weather cap from the mini-USB port. 3. Plug the small end of the AC charger into the mini-USB port. To connect the Edge to your computer using the USB cable, see page 8. 4. Charge the Edge for at least three hours before you begin using it.
Getting Started 2. Place the rubber disk on the back of the bike mount. The rubber tabs align with the back of the bike mount so it stays in place. 3. Place the bike mount on the bike stem. 4. Attach the bike mount securely using the two bands. Rubber disk 5. Align the tabs on the back of the Edge with the bike mount notches. 6. Press down slightly and turn the Edge clockwise until it locks into place.
Getting Started Turning on the Edge Press and hold POWER to turn on the Edge. Configuring the Edge The first time you turn on the Edge, you are prompted to configure system settings and user profile settings. • Follow the on-screen instructions to complete the initial setup. • Press ▼ or ▲ to view choices and change the default selection. • Press ENTER to make a selection. 4 Icons Battery charge level GPS is on and receiving signals. GPS is turned off. Heart rate monitor is active.
Getting Started Buttons Each Edge button has multiple functions. Button Description POWER/ LIGHT Press and hold POWER to turn the device on and off. Press LIGHT to activate the backlight. Press any button to extend the backlight for 15 seconds. BACK Press BACK to cancel or return to the previous menu. Edge 500 Owner’s Manual START/ STOP Press START/STOP to start and stop the timer. ▼▲ Press ▼ or ▲ to select menus and settings. Press and hold ▼ or ▲ to scroll quickly through settings.
Getting Started Acquiring Satellite Signals It may take 30 to 60 seconds to acquire signals. 1. Go outdoors to an open area. 2. Make sure that the front of the Edge is oriented toward the sky. 3. Wait while the Edge searches for satellites. Do not begin moving until the locating satellite page disappears. Note: To turn off the GPS receiver and use the Edge indoors, see page 44. 6 Optional ANT+ Sensors note: If you do not need to set up ANT+ sensors, you can skip this step.
Getting Started Going for a Ride Before you can record history, you must acquire satellite signals (page 6). 1. Press and hold MENU to view the timer page. Saving Your Ride Data Press and hold RESET to save your ride data and reset the timer. Using Garmin Connect Garmin Connect is web-based software for storing and analyzing your data. 1. Go to www.garminconnect.com/ start. 2. Follow the on-screen instructions. 2. Press START to start the timer.
Getting Started Transferring History to Your Computer 1. Connect the USB cable to a USB port on your computer. 2. Pull up the weather cap from the mini-USB port. 4. Go to www.garminconnect.com/ start. 5. Follow the instructions included with the software. Mini-USB port under weather cap 3. Plug the small end of the USB cable into the mini-USB port.
Training with Your Edge Training with Your Edge Alerts You can use Edge alerts to train toward specific time, distance, calorie, heart rate, cadence, and power goals. Using Time, Distance, and Calorie Alerts 1. Press and hold MENU. 2. Select Training > Alerts. 3. Select Time Alert, Distance Alert, or Calorie Alert. 4. Turn on the alert. 5. Enter a time, distance, or calorie amount. 6. Go for a ride. Each time you reach the alert amount, the Edge beeps and displays a message.
Training with Your Edge • Select Cadence Alert to set the fast and slow cadence amounts in revolutions of the crank arm per minute (rpm). • Select Power Alert to set the minimum and maximum power amounts in watts. 4. Go for a ride. Each time you exceed or drop below the specified heart rate, cadence, or power amount, the Edge beeps and displays a message. Note: To turn on audible tones for messages, see page 40.
Training with Your Edge Using Auto Lap by Position You can use Auto Lap to automatically mark the lap at a specific position. This feature is helpful for comparing your performance over different parts of a ride (for example, a long climb or training sprints). 1. Press and hold MENU. 2. Select Settings > Bike Settings > Auto Lap. 3. In the Auto Lap Trigger field, select By Position. 4.
Training with Your Edge Using Auto Pause You can use Auto Pause to pause the timer automatically when you stop moving or when your speed drops below a specified value. This feature is helpful if your ride includes stop lights or other places where you need to slow down or stop. ® Note: The paused time is not saved with your history data. 1. Press and hold MENU. 2. Select Settings > Bike Settings > Auto Pause. 3. Select an option: • Select Off.
Training with Your Edge Courses Courses allow you to train using a previously recorded activity. You can follow the course trying to match or exceed previously set goals. For example, if the original course was completed in 30 minutes, you will race against a Virtual Partner® trying to complete the course in under 30 minutes. You can create a course from your own activity, or you can send a course from Garmin Connect to your device.
Training with Your Edge • Select Profile to preview the elevation profile, and press BACK to return to the course list. 5. Press START. History is recorded even if you are not on the course. The “Course Complete” message appears when you finish. 6. Go for a ride. 14 7.
Training with Your Edge Off Course Options You can include a warmup before you begin your course. Press START to begin the course, and then warm up as normal. Stay away from your course path as you warm up. When you are ready to begin, head toward your course. When you are on any part of the course path, the Edge displays an “On Course” message. Note: As soon as you press START, your Virtual Partner starts the course and does not wait for you to warm up.
Training with Your Edge Changing the Course Speed 1. Press and hold MENU. 2. Select Training > Courses. 3. Select the course from the list. 4. Select Do Course. 5. Press LIGHT. 6. Use▼ and ▲ to adjust the percentage of time to complete the course. For example, to improve your course time by 20%, enter a course speed of 120%. You will race against the Virtual Partner to finish a 30-minute course in 24 minutes. Stopping a Course Press and hold MENU, and select Training > Stop Course.
Training with Your Edge 5. Select Duration to specify how the step will be measured. For example, select Distance to end the step after a specific distance. If you select Open, you can press LAP to end the step during your workout. 6. If necessary, enter a value in the field below Duration. 7. Select Target to choose your goal during the step. For example, select Heart Rate to maintain a consistent heart rate during the step. 8. If necessary, select a target zone or enter a custom range.
Training with Your Edge For example, you can repeat a 5-mile step for 60 minutes or until your heart rate reaches 160 bpm. 3. In the Back To Step field, select a step to repeat. 4. If necessary, select Yes in the Rest Lap field. 5. Press BACK to continue. Starting a Workout 1. Press and hold MENU. 2. Select Training > Workouts. 3. Select the workout. 4. Select Do Workout. 5. Press START. 6. Go for a ride. 7.
Training with Your Edge 8. Press BACK to save and to exit. Deleting a Workout 1. Press and hold MENU. 2. Select Training > Workouts. 3. Select the workout. 4. Select Delete Workout > Yes.
ANT+ Sensors ANT+ Sensors The Edge is compatible with the following ANT+ accessories: • Heart rate monitor (page 21) • GSC 10 speed and cadence sensor (page 25) • Third-party ANT+ sensors (page 30) For information about purchasing additional accessories, go to http://buy.garmin.com. Tips for Pairing ANT+ Sensors with Your Garmin Device 10 m away from other ANT+ sensors. • Bring the Garmin device within range (3 m) of the ANT+ sensor.
ANT+ Sensors Putting on the Heart Rate Monitor caution The heart rate monitor may cause chafing when used for long periods of time. To alleviate this issue, apply an anti-friction lubricant or gel to the center of the hard strap where it contacts your skin. Do not use gels or lubricants that contain sunscreen. Do not apply anti-friction gel or lubricant on the electrodes. Wear the heart rate monitor directly on your skin, just below your breastplate.
ANT+ Sensors Using the Heart Rate Monitor 1. Turn on the Edge. 2. Bring the Edge within range (3 m) of the heart rate monitor. 3. Press and hold MENU. 4. Select Settings > Bike Settings > Heart Rate > ANT+ HR. 5. Select Yes > Rescan. 6. Press BACK to return to the main menu. When the heart rate monitor is paired, a message appears and the heart rate icon appears on the main menu. 7. Customize optional data fields (page 36). 8. Go for a ride.
ANT+ Sensors Heart Rate Zones 1 % of Maximum Heart Rate or Resting Heart Rate 50% to 60% 2 60% to 70% 3 70% to 80% 4 80% to 90% 5 90% to 100% Perceived Exertion Benefits Relaxed, easy pace; rhythmic breathing Comfortable pace; slightly deeper breathing, conversation possible Moderate pace; more difficult to hold conversation Beginning-level aerobic training; reduces stress Basic cardiovascular training; good recovery pace Improved aerobic capacity; optimal cardiovascular training Improved ana
ANT+ Sensors About Heart Rate Zones caution Consult your physician to specify heart rate zones that are appropriate for your fitness level and health condition. cardiovascular capacity and strength. • Knowing your heart rate zones can prevent you from overtraining and can decrease your risk of injury. Many athletes use heart rate zones to measure and increase their cardiovascular strength and improve their level of fitness. A heart rate zone is a specified range of heartbeats per minute.
ANT+ Sensors 2. Use a coin to twist the cover counter-clockwise so the arrow on the cover points to OPEN. 3. Remove the cover and battery. 4. Wait 30 seconds. 5. Insert the new battery with the positive side facing up. Note: Be careful not to damage or lose the O-ring gasket on the cover. 6. Use a coin to twist the cover clockwise so the arrow on the cover points to CLOSE.
ANT+ Sensors Reset button Indication line Indication line Cable ties GSC 10 on Rear Chain Stay 2. Loosely attach the GSC 10 using two cable ties. 3. Attach the pedal magnet to the crank arm using the adhesive mount and a cable tie. The pedal magnet must be within 5 mm of the GSC 10. The indication line on the pedal magnet must line up with the indication line on the GSC 10. 26 Cable tie Pedal Magnet on Crank Arm 4. Unscrew the spoke magnet from the plastic piece. 5.
ANT+ Sensors Sensor arm indication line Spoke magnet GSC 10 Pedal magnet GSC 10 and Magnet Alignment 6. Loosen the screw on the sensor arm. 7. Move the sensor arm to within 5 mm of the spoke magnet. You can also tilt the GSC 10 closer to either magnet for improved alignment. Edge 500 Owner’s Manual 8. Press the Reset button on the GSC 10. The LED turns red, then green. 9. Pedal to test the sensor alignment. The red LED blinks each time the pedal magnet passes the sensor.
ANT+ Sensors Using the GSC 10 1. Turn on the Edge. 2. Bring the Edge within range (3 m) of the GSC 10. 3. Press and hold MENU. 4. Select Settings > Bike Settings > [Bike 1] > ANT+ Spd/Cad. 5. Select Yes > Rescan. 6. Press BACK to return to the main menu. When the GSC 10 is paired, a message appears and the cadence icon appears on the main menu. 7. Customize optional data fields (page 36). 8. Go for a ride. 28 About the GSC 10 Cadence data from the GSC 10 is always recorded.
ANT+ Sensors To turn the non-zero averaging on or off, press and hold MENU, and select Settings > Bike Settings > Data Avg. Replacing the GSC 10 Battery The GSC 10 contains a userreplaceable CR2032 battery. Note: Contact your local waste disposal department to properly dispose of batteries. 1. Locate the circular battery cover on the side of the GSC 10. Battery cover 2. Use a coin to twist the cover counter-clockwise until it is loose enough to remove (arrow points to unlocked). 3.
ANT+ Sensors Third-Party ANT+ Sensors For a list of third-party ANT+ sensors that are compatible with the Edge, go to www.garmin.com/intosports. Calibrating Your Power Meter For calibration instructions specific to your power meter, refer to the manufacturer’s instructions. Before you can calibrate your power meter, it must be properly installed and actively recording data. 1. Press and hold MENU. 2. Select Settings > Bike Settings > [Bike 1] > ANT+ Power > Calibrate. 3.
ANT+ Sensors ANT+ Sensor Troubleshooting Problem The ANT+ sensor will not pair with my device. Solution • Stay 10 m away from other ANT sensors while pairing. • Bring the device within range (3 m) of the heart rate monitor while pairing. • If the problem persists, replace the battery. I have a third-party Make sure that it is compatible with the Edge (www.garmin ANT+ sensor. .com/intosports). The heart rate monitor A smaller elastic strap is sold separately. Go to strap is too big. http://buy.garmin.
History History Your Edge automatically saves history when the timer is started. The Edge can save at least 180 hours of ride data with typical use. When the Edge memory is full, a message appears. The Edge does not automatically delete or overwrite your history. See page 33 to learn how to delete history. History includes time, distance, calories, average speed, maximum speed, altitude, and detailed lap information. Edge history can also include heart rate, cadence, and power.
History Deleting History Data Recording 1. Press and hold MENU. 2. Select History > Delete. 3. Select an option: • Select Indv. Activities to delete one activity at a time. • Select All Activities to delete all ride data from the history. • Select Old Activities to delete activities recorded more than one month ago. • Select All Totals to reset the ride distance and time totals. Note: This does not delete any history. 4. Select Yes.
Data Management Data Management You can use the Edge as a USB mass storage device. note: The Edge is not compatible with Windows® 95, 98, Me, or NT. It is also not compatible with Mac® OS 10.3 and earlier. Connecting the USB Cable notice To prevent corrosion, thoroughly dry the mini-USB port, the weather cap, and the surrounding area before charging or connecting to a computer. 1. Connect the USB cable to a USB port on your computer. 2. Pull up the weather cap from the mini-USB port. 34 3.
Data Management Deleting Files NOTICE Your device memory contains important system files that should not be deleted. After you have connected the device to your computer, you can manually delete files. 1. Open the Garmin drive or volume. 2. Select the file. 3. Press the Delete key on your keyboard. Edge 500 Owner’s Manual Disconnecting the USB Cable When you are finished managing your files, you can disconnect the USB cable. 1.
Settings Settings You can customize the following settings and features: • • • • • Data fields (page 37) System settings (page 40) User profiles (page 42) Bike profiles (page 42) GPS settings (page 44) Customizing Your Data Fields You can set up custom data fields for three training data pages. To turn off an optional page, set the number of data fields to zero. 5. Use ▼, ▲, and ENTER to change the data fields. 6. Repeat steps 3 through 5 for each page you want to customize. 1.
Settings Data Fields Data fields with the * symbol display statute or metric units. Data fields with the ** symbol require an ANT+ sensor. Data Field Description GPS Accuracy * Margin of error for your exact location. For example, your GPS location is accurate to within +/- 12 feet. Grade Calculation of rise over run. For example, if for every 10 feet you climb (elevation) you travel 200 feet (distance), your grade is 5%. Data Field Description Cadence ** Revolutions of the crank arm per minute.
Settings Data Field Description Data Field Description HR – Avg. %HRR ** Average percentage of heart rate reserve (maximum heart rate minus resting heart rate) for the run. HR Zone ** HR – Avg. %Max. ** Average percentage of maximum heart rate for the run. Current range of heart rate (1 to 5). The default zones are based on your user profile, maximum heart rate, and resting heart rate. Laps Number of laps completed. HR – Lap ** Average heart rate in the current lap.
Settings Data Field Description Data Field Description Power – Lap ** Average power output in the current lap. Temperature * Power – Max. ** Top power achieved during the current ride. Power Zone ** Current range of power output (1 to 7) based on your FTP or custom settings. Speed * Current speed. Speed – Avg. * Average speed for the ride. Current temperature in Fahrenheit or Celsius.
Settings Data Field Description Time of Day Current time of day based on your time settings (format, time zone, and daylight saving time). Total Ascent * Total elevation gain for the current ride. Total Descent * Total elevation lost for the current ride. Vertical Speed * Rate of ascent or descent in feet/meters per hour. VS – 30s Avg. * The 30-second moving average of vertical speed. Changing Your System Settings 3. Turn the tones for keys and messages on or off. Changing the Backlight 1.
Settings Changing the Configuration Settings You can modify all of the settings you configured in the initial setup. 1. Press and hold MENU. 2. Select Settings > System. 3. Select an option: • Select System Setup to modify language, position format, unit format, and time format. • Select Initial Setup to modify all of the configuration settings in the initial setup. 4. Follow the on-screen instructions.
Settings Changing Your User Profile Settings The Edge uses information that you enter about yourself to calculate accurate ride data. 1. Press and hold MENU. 2. Select Settings > User Profile to update gender, age, weight, height, and activity class settings. Use the table on page 53 to determine your activity class. 3. Follow the on-screen instructions. About Calories Calorie expenditure and heart rate analysis technology is provided and supported by Firstbeat Technologies Ltd.
Settings Switching Bikes After you customize your bike profiles on the Edge, select your bike. 1. Press and hold MENU. 2. Select Settings > Bike Settings > [Active Bike Name] > Bike Details. 3. Select the bike you want to use. Changing the Start Notice This feature automatically detects when your Edge has acquired satellites and is moving. It is a reminder to start the timer so you can record your ride data. 1. Press and hold MENU. 2. Select Settings > Bike Settings > Start Notice.
Settings GPS Settings GPS settings include the following: • Turning satellites off (page 44) • Viewing the satellite page (page 44) • Using elevation points (page 45) Training Indoors 1. Press and hold MENU. 2. Select GPS > GPS Status. 3. Select Off. When GPS is off, speed and distance data are not available unless you have an optional sensor that sends speed and distance data to the Edge (such as the GSC 10. The next time you turn on the Edge, it will search for satellite signals again.
Settings Setting Elevation Points You can save up to 10 elevation points. Using an elevation point each time you begin a particular training ride provides more-consistent and more-accurate elevation data. 1. Press and hold MENU. 2. Select GPS > Set Elevation. 3. Enter a descriptive name. 4. Enter the known elevation. 5. Select Save. The next time you start the timer, the Edge automatically searches for elevation points within 30 m of your location.
Appendix Appendix Registering Your Device Help us better support you by completing our online registration today: • Go to http://my.garmin.com. • Keep the original sales receipt, or a photocopy, in a safe place. About the Edge To display important software information and your unit ID, press and hold MENU, and select Settings > About Edge. 46 Updating the Software 1. Select an option: • Use WebUpdater. Go to www.garmin.com/products /webupdater. • Use Garmin Connect. Go to http://connect.garmin.
Appendix information, or contact Garmin (Europe) Ltd. by phone at +44 (0) 870.8501241. Using the Backlight • Press LIGHT to turn on the backlight. • Press any button to extend the backlight another 15 seconds. NOTE: Alerts and messages also activate the backlight. • Change the backlight settings (page 40). Buying Optional Accessories Go to http://buy.garmin.com, or contact your Garmin dealer for information about optional accessories and replacement parts.
Appendix Edge Specifications Bike Mount Specifications Radio frequency/ protocol 2.4 GHz wireless communications protocol Bands (O-rings) GPS receiver High-sensitivity integrated GPS receiver Altimeter Internal barometric altimeter 48 Two sizes: • 1.3 × 1.5 × 0.9 in. AS568-125 • 1.7 × 1.9 × 0.9 in. AS568-131 Note: Use EPDM (Ethylene Propylene Diene Monomer) replacement bands only. Go to http://buy .garmin.com, or contact your Garmin dealer.
Appendix Heart Rate Monitor Specifications Heart Rate Monitor Specifications Water resistance 32.9 ft. (10 m) Transmission range Approximately 9.8 ft. (3 m) Radio frequency/ protocol Battery User-replaceable CR2032 (3 volts) Perchlorate Material – special handling may apply. See www.dtsc.ca.gov /hazardouswaste /perchlorate.
Appendix GSC 10 Specifications Wheel Size L (mm) Radio frequency/ protocol 22 × 1-3/8 1770 22 × 1-1/2 1785 24 × 1 1753 24 × 3/4 Tubular 1785 24 × 1-1/8 1795 24 × 1-1/4 1905 24 × 1.75 1890 2.4 GHz wireless communications protocol Wheel Size and Circumference The wheel size is marked on both sides of the tire. To modify your bike profile, see page 42. 24 × 2.00 1925 Wheel Size L (mm) 24 × 2.125 1965 12 × 1.75 935 26 × 7/8 1920 14 × 1.5 1020 26 × 1(59) 1913 14 × 1.
Appendix Wheel Size L (mm) Wheel Size L (mm) 26 × 1.50 2010 700 × 20C 2086 26 × 1.75 2023 700 × 23C 2096 26 × 1.95 2050 700 × 25C 2105 26 × 2.00 2055 700 × 28C 2136 26 × 2.10 2068 700 × 30C 2170 26 × 2.125 2070 700 × 32C 2155 26 × 2.35 2083 700C Tubular 2130 26 × 3.
Appendix Activity Classes How active are you? How often do you exercise? How long do you exercise? 0 No exercise - - 1 Occasional, light exercise Once every two weeks Less than 15 minutes 2 3 4 5 Regular exercise and training 15 to 30 minutes Once a week Approximately 30 minutes 2 to 3 times per week Approximately 45 minutes 45 minutes to 1 hour 6 1 to 3 hours 7 8 9 10 Daily training 3 to 5 times per week 3 to 7 hours Almost daily 7 to 11 hours Daily 11 to 15 hours More than 15 ho
Appendix Troubleshooting Problem The buttons do not respond. How do I reset the Edge? I want to clear all the user data from my Edge. My Edge does not acquire satellite signals. The battery gauge does not seem accurate. The battery does not last long. How do I know my Edge is in USB mass storage mode? Solution Press and hold POWER, MENU, and RESET simultaneously to reset the Edge. Note: This does not erase any of your data or settings. 1. Turn off the Edge. 2.
Appendix Problem My Edge is connected to the computer, but it will not go into mass storage mode. I cannot see any new removable drives in my list of drives. My course file was renamed. Some of my data is missing from my Edge history. I need to replace the bands for the mount. 54 Solution You may have loaded a corrupted file. 1. Disconnect the Edge from your computer. 2. Turn off the Edge. 3. Press and hold MENU while you connect the Edge to your computer.
Index Index A accessories 47 acquiring satellite signals 6, 53 activity classes 42, 52 alerts 9 ANT+ sensors 6, 20–31 troubleshooting 31 Auto Lap 10, 11 Auto Pause 12 Auto Scroll 12 B backlight 40, 47 bands 3, 48, 54 battery 53 charging 1 conserving 40 bike mount 2, 48 bike profiles 42, 43 buttons 5 Edge 500 Owner’s Manual C cadence alerts 10 data fields 37 training 28 calibrating your power meter 30 calorie alerts 9 calories 37 charging the Edge 1, 2 clearing user data 53 cours
Index H heart rate alerts 9 data fields 37 settings 22 zones 22–24 heart rate monitor battery 24 putting on 21 specifications 49 using 22 history 32, 54 deleting 33 transferring 8 viewing 32 I icons 4 initial setup 4, 41 installing the Edge 2 L lithium-ion battery 1, 47 loading files 34 56 M mount 2, 48 O O-rings (bands) 48 P pairing ANT+ sensors 6, 20 paused time 12 pedal magnet 26 power alerts 10 data fields 38 data recording 33 meter 30 zones 30 product registration 46 pro
Index T technical specifications 47 time alerts 9 data fields 39 zones and formats 41 timer 7, 32 tire size 42 tones 40 training indoors 44 training with your Edge 9 transferring data 8, 34 troubleshooting 31, 53 W weather cap 2, 8, 34 wheel sizes 42, 50 workouts 16–19 loading 34 Z zones heart rate 22–24 power 30 U unit ID 46 updating software 46 USB 2, 8, 34, 53 user profile 42 V vertical speed 40 Virtual Partner 13, 15 Edge 500 Owner’s Manual 57
For the latest free software updates (excluding map data) throughout the life of your Garmin products, visit the Garmin Web site at www.garmin.com. TA-2012/1220 © 2009–2013 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK Garmin Corporation No. 68, Zhangshu 2nd Road, Xizhi Dist., New Taipei City, 221, Taiwan (R.O.C.