Installation Manual
©2015 CBC Americas Corp. All Rights Reserved 06/2015 Page 1 of 1
INSTALLATION MANUAL – WB-1W Wall Mount
Unpacking
Unpack carefully. This is mechanical equipment and should be
handled with care. If an item appears to have been damaged in
shipment, replace it properly in its carton and notify the shipper. If
any items are missing, notify CBC America Corp (CBC). The shipping
carton is the safest container in which the unit may be transported.
Save it for possible future use.
Service
If the unit ever needs repair service, the customer should contact CBC
for a return materials authorization (RMA) and shipping instructions.
Care and Maintenance
Perform routine maintenance to keep the unit dust free.
Model Designation
WB-1W Feed-Through Wall Mount with Thermal Camera
Adapter Plate
Description
This indoor/outdoor mounting equipment is designed for fixed camera
or camera housing installations up to 9kg (20lb) rated load. This
model is made of lightweight aluminum and features welded
construction, providing an extremely rigid camera mount. This
bracket have been specifically designed for the ZNT6 Fixed Series
Thermal Cameras.
Hardware Kit –WB-1W
1 x Allen Wrench
4 x Plastic Wall Anchor
4 x Screw, Mounting
4 x Screw, M5 x 8mm Flat Head, Stainless Steel
2 x #10 Flat Washer, Stainless Steel
2 x #10 Nut, Stainless Steel
Tools Required
Drill with appropriate sized bit for fasteners used
#2 Cross Recessed (Phillips Head) Screwdriver
3/8” Nut Driver or Wrench
Certification
Camera installation should be performed by a licensed professional
and conform to the National Electrical Code (NEC) and any applicable
local codes.
Installation
Determine a secure wall mounting location.
Warning: These mounts are designed to support a load only in
a vertical direction. Mounts MUST be positioned as shown in the
SPECIFICATIONS
section of this manual.
1. Cautions: The fasteners provided in the hardware kit may not
be ideal for all installations.
a. For a secure installation, use four 8-mm (5/16-in diameter
fasteners (not included).
b. If bolts are used, they should extend through the mounting
surface and be secured with flat washers, lock washers, and
nuts on the opposite side. Each bolt must have a minimum
pull-out strength of 200kg (450lbs).
c. If studs are used, they should be anchored in concrete or
welded to a steel backer plate. Each stud must have a
minimum pull-out strength of 200kt (450lbs).
d. If the wall mount is attached to wood or to a blind structure
(with no access to the rear), each fastener must have a
minimum pull-out strength of at least 200kg (450lbs).
2. Locate the four holes or stud locations using the flange as a
template (four holes equally spaced on a 69.9mm (2-3/4-in) bolt
circle.
3. Feed wires through the large hole in the flange or through the
slot on the surface where the camera mounts.
4. Refer to instructions included with the camera for wiring
instructions.
5. Install the mount using bolts or studs at least 8-mm (5/16-in) in
diameter.
6. To mount the camera:
a. Attach Adapter Plate to Camera using 4 x M5x8mm flat
head screws from hardware kit.
b. Position housing over mount and adapter plate studs with
the holes in the mount. Install #10 washers and nuts using
3/8” nut driver or wrench. If needed, loosen wall mount
screws to adjust mount head (use Allen wrench from
hardware kit).
c. Lock mount head in position by using the supplied Allen
wrench to tighten screws.
Specifications
WB-1W Indoor/Outdoor Feed-through Mount
Maximum Load: 9kg (20lbs)
Mounting Head: Adjustable 360° Pan, 180° Tilt
Finish: White Powder Coat
Approx Weight:
WB-1W: 0.41 kg (0.9lb)
Figure 1 - WB-1W
Figure 2 - WB-1W Adapter Plate Installation
CBC Americas Corp.
55 Mall Drive, Commack NY 11725
Tel: 800-422-6707
www.ganzsecurity.com