Brochure

ManualsBrandsGantner Electronic ManualsElectronicsAccess Control Terminal, Access Control Terminal with Biometry

Function description

The GAT Access 6100 F reads contact-free data carriers and checks

and grants authorisations. The user holds the data carrier over the round

scan field and selects the required service via the acknowledge key. The

integrated 4-segment LED display, monochrome LCD display and acoustic

signal indicate authorisation.

Via the fingerprint reader GAT FR 055 the identification of the visitors

is verified by comparing their fingerprints with the fingerprint templates

(two templates per visitor) stored on the visitor‘s personal data carriers.

The combination of RFID data carriers and fingerprints allows for optimal

protection against misuse of data carriers.

For capturing the fingerprints and storing them to the data carriers the GAT

Access 6100 F Enrollment Station is used.

Highlights

•

Activation of turnstiles, doors etc. via relay output

•

Feedback input

•

User guidance via monochrome display (LCD), 4-segment LED display,

illuminated round scan field and beeper

•

Secure data transmission between reader and data carrier

•

Read/write frequency 13.56 MHz

•

Reading MIFARE

Standard data carriers

•

Expandabilities for verification via fingerprint

•

Opening of housing only possible with special tool

•

Plug & Play installation

GAT Access 6100 F

Access Control Terminal with Biometry

Application

The GAT Access 6100 F with fingerprint reader GAT FR 055 is a stylish

terminal for access control in leisure facilities such as swimming pools,

spas and gyms. Identification at the terminal is by contact-free RFID data

carrier (Radio Frequency Identification).

With the fingerprint reader GAT FR 055 access control is extended by

verification with biometric data, which enables optimal protection against

misuse of personal data carriers.

Information for user guidance is displayed via a graphical monochrome

display (LCD).

Description PartNo.

GAT Access 6100 F

Terminal for entry control with integrated, contactless

MIFARE

reader, with black-white display (LCD)

776487

GAT FR 055

Fingerprint reader for GAT Access 6100 F, wall mounting

557433

GAT FR 055 Weather Cover

Weather protection cover for GAT FR 055 and

GAT FR 055 FIU 3k

174529

www.gantner.com

Order information

Description PartNo.

GAT Access 6100 F Enrollment Station

Table station for capturing fingerprints

174327

GAT Reader WK

Tool to open the reader housing

581683

Accessories

Valid as from July 31

2013 • Technical data subject to modifications without notice!

DB_GAT-ACCESS6100F--BIO-EN_11.indd • PartNo.: 243526

GAT Access 6100 F

Fingerprint reader

GAT FR 055

Summary of content (4 pages)

PAGE 1
GAT Access 6100 F Access Control Terminal with Biometry Application The GAT Access 6100 F with fingerprint reader GAT FR 055 is a stylish terminal for access control in leisure facilities such as swimming pools, spas and gyms. Identification at the terminal is by contact-free RFID data GAT Access 6100 F carrier (Radio Frequency Identification).
PAGE 2
Technical data Nominal voltage: 12/24 VDC (SELV - safety extra-low voltage) Control elements: - 4 function keys - RFID reader Permitted input voltage: 10 to 28 VDC Host interface: Ethernet 10/100 MBit/s Aver. power consumption: - Full operation sensor in: 4.5 W - Full operation sensor out: 3.5 W Signal inputs: Data storage: Internal EEPROM memory for configuration and booking memory, data preservation min.
PAGE 3
Mounting and installation instructions 4. Electrical connection Drill mounting holes on a flat background (e.g. concrete wall) according to The connection cables (see (4) in previous drawing) are connected at the the following dimensional drawing. Use the three holes labelled (a). device back part of the GAT Access 6100 F (se page 4). 14.1 mm (0.56”) 1. Mounting holes 94.4 mm (3.72”) 69 mm (2.72”) 60 mm (2.36”) 13 mm (0.51”) 5.
PAGE 4
Electrical connections TCP/IP with external power supply GAT Access 6100 e.g. Turnstile B A GND VOut+ Mains power Motor control Power supply unit e.g. GAT Power Supply SP014/1 TX + TX RX + RX - GND C1 NO 1 VIN + IN1 + IN1 - Feedback control TCP/IP 1 M Power supply Connection to the device upper part DC supply (see technical data), e.g. via GANTNER GAT Power Supply Attention: The socket for the connection cable between the device back SP014/1.