Installation Instructions

ManualsBrandsGallagher ManualsElectronicsProx Readers T21 PIV

Table Of Contents

Installation Note
Contents
1 Introduction
2 Before you begin
3 Distance between readers
- The distance separating any two proximity readers must not be less than 200 mm (8 in) in all directions. When mounting a proximity reader on an internal wall, check that any reader fixed to the other side of the wall is not less than 200 mm (8 in) away.
4 Installation
5 Screen brightness
- When the reader is in use the screen brightness will be set to full. If the reader hasn't been used for 30 seconds, the screen brightness is dimmed. If the reader hasn't been used for 30 minutes, the screen is turned off.
- Note: The reader screen can be set to on at all times ('Always on' setting enabled on the HBUS Contact Card Reader item's property page in Command Centre). If this setting is enabled, the reader's screen will not turn off after 30 minutes, but will di...
6 Information screen
- To display the supported card technologies and the software version numbers of the reader, press and hold the '#' key for 3 seconds. The Information screen is displayed.
7 LED indications
8 Accessories
9 Icons
10 Technical specifications
11 Approvals and Compliance Standards
- US - Equipment: com, burg and acc reader CA - Equipment: com, burg reader
12 Mounting Dimensions

3E5334 Gallagher T21 PIV Reader REV1 | Edition 1 | April 2021

Page 1

Gallagher

T21 PIV Reader REV1

Installation Note

T21 PIV Reader - Black REV1: C305505

T21 PIV Reader - White REV1: C305506

Summary of content (27 pages)

PAGE 1
Gallagher T21 PIV Reader REV1 Installation Note T21 PIV Reader - Black REV1: C305505 T21 PIV Reader - White REV1: C305506 3E5334 Gallagher T21 PIV Reader REV1 | Edition 1 | April 2021 Copyright © Gallagher Group Limited Page 1
PAGE 2
Disclaimer This document gives certain information about products and/or services provided by Gallagher Group Limited or its related companies (referred to as "Gallagher Group"). The information is indicative only and is subject to change without notice meaning it may be out of date at any given time.
PAGE 3
Contents 1 Introduction .............................................................................................................................................4 2 Before you begin ......................................................................................................................................4 2.1 Shipment contents ..........................................................................................................................4 2.2 Power supply ........................
PAGE 4
1 Introduction The Gallagher T21 PIV Reader is a contact card and smart card proximity reader. The reader's contact slot reads PIV card data, for PIV PIN validation. The reader connects to a Gallagher Controller 6000 High Spec PIV (C305101). The reader sends information to the Controller and acts upon information sent from the Controller. The reader itself does not make any access decisions.
PAGE 5
2.3 Cabling The Gallagher T21 PIV Reader requires a minimum cable size of 4 core 24 AWG (0.2 mm2) stranded security cable. This cable allows the transmission of data (2 wires) and power (2 wires). When using a single cable to carry both power supply and data, both the power supply voltage drop and data requirements must be considered. Although the reader is specified to operate at 9 Vdc, for good engineering design it is recommended that the voltage at the reader should be approximately 12 Vdc.
PAGE 6
Controller 6000 HBUS Device H1 H5 HBUS Device H4 H8 HBUS Device HBUS Module HBUS Device Terminate Terminate HBUS Device HBUS Device Terminate Terminate Cable distance Single reader connected using HBUS data only in a single cable Single reader connected using power and data in a single cable *** CAT 5e or better** 4 twisted pair Each 2 x 0.2 mm2 (24 AWG) 500 m (1640 ft) 50 m (165 ft) BELDEN 9842** (shielded) 2 twisted pair Each 2 x 0.
PAGE 7
3 Distance between readers The distance separating any two proximity readers must not be less than 200 mm (8 in) in all directions. When mounting a proximity reader on an internal wall, check that any reader fixed to the other side of the wall is not less than 200 mm (8 in) away. 4 Installation ATTENTION: This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing.
PAGE 8
Note: There is no room for the building cable to be squeezed into the reader bezel. The building cable must remain within the flush box or wall cavity. 2. Run the building cable through the reader bezel. 3. Secure the bezel to the flush box using the two screws provided. When securing the bezel to a vertical, rectangular flush box, use the 6-32 UNC screws provided. When securing the bezel to a BS 4662 British Standard square flush box, use the M3.5 screws provided. 4.
PAGE 9
7. The reader connects to a Gallagher Controller 6000 High Spec PIV, a Gallagher 4H/8H HBUS Module (attached to the Controller 6000 High Spec PIV), or a Gallagher HBUS Door Module (connected to a Controller 6000 High Spec PIV). Unplug the reader's terminal block from the PCB. Connect the wires from the building cable to the terminal block as shown. Plug the terminal block back into the PCB.
PAGE 10
9. Fit the facia assembly into the bezel by clipping the small lip, into the top of the bezel and holding the top, press the bottom of the facia assembly down into the bezel. 10. Insert the M3 Torx Post Security screw (using a T10 Torx Post Security screwdriver) through the hole below the reader facia. Note: The Torx Post Security screw needs only to be lightly tightened.
PAGE 11
. Removal of the facia assembly is a simple reversal of these steps. Hint: After removal of the security screw, press the top of the facia. The bottom of the facia will exit the reader bezel. Alternatively, carefully use an electrical screwdriver to lever the bottom of the facia away from the bezel. 5 12. Configure the reader in Command Centre. Refer to the topic "Configuring an HBUS Contact Card Reader" in the Command Centre Configuration Client Online Help. 13.
PAGE 12
8 9 Accessories Accessory Product Code T21 Bezel - Black REV1 C305285 T21 Bezel - White REV1 C305286 Icons Insert Card Remove Card Armed Present Card Card For Access or Waiting For Authorisation Enter PIN/Code Access Granted Access Denied Free Access Not Allowed Card or Code 3E5334 Gallagher T21 PIV Reader REV1 | Edition 1 | April 2021 Copyright © Gallagher Group Limited Page 12
PAGE 13
10 Technical specifications Routine maintenance: Not applicable for this reader. Cleaning: This reader should be cleaned with mild soapy water only. Do not use solvents or abrasives. Voltage: 9 Vdc - 16 Vdc (at the reader) Current : Inactive1 Active2 T21 PIV Reader (at 9 Vdc): 154 mA 282 mA T21 PIV Reader (at 13.
PAGE 14
11 Approvals and Compliance Standards This symbol on the product or its packaging indicates that this product must not be disposed of with other waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
PAGE 15
12 Mounting Dimensions IMPORTANT This picture is not to scale, therefore use the measurements provided.
PAGE 16
Open Source Software License Notice This product includes software code developed by third parties, including software code subject to the GNU General Public License (“GPL”), the GNU Library General Public License (“LGPL”), and a variety of additional licenses, including BSD-style licenses. As applicable, the terms of these licenses, and information on obtaining access to the open source code used in this product, are available for free download from https://security.gallagher.com/oss.
PAGE 17
3.
PAGE 18
Gnomovision version 69, Copyright (C) 19yy name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details. The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License.
PAGE 19
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
PAGE 20
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License.
PAGE 21
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code.
PAGE 22
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4.
PAGE 23
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13.
PAGE 24
Finally, many people asked us for a preferred form for a credit/disclaimer to use in compliance with this license. We thus encourage you to use the following text: """ Portions of this software are copyright © The FreeType Project (www.freetype.org). All rights reserved. """ Please replace with the value from the FreeType version you actually use. Legal Terms =========== 0.
PAGE 25
Copyright (c) 1997-2012 University of Cambridge All rights reserved. PCRE JUST-IN-TIME COMPILATION SUPPORT Written by: Zoltan Herczeg Email local part: hzmester Emain domain: freemail.hu Copyright(c) 2010-2012 Zoltan Herczeg All rights reserved. STACK-LESS JUST-IN-TIME COMPILER Written by: Zoltan Herczeg Email local part: hzmester Emain domain: freemail.hu Copyright(c) 2009-2012 Zoltan Herczeg All rights reserved. THE C++ WRAPPER FUNCTIONS Contributed by: Google Inc. Copyright (c) 2007-2012, Google Inc.
PAGE 26
Copyright (c) 1993 The Regents of the University of California. strlcpy.c: Copyright (c) 1998 Todd C. Miller win32select.c: Copyright (c) 2003 Michael A. Davis evport.c: Copyright (c) 2007 Sun Microsystems ht-internal.h: Copyright (c) 2002 Christopher Clark minheap-internal.h: Copyright (c) 2006 Maxim Yegorushkin
PAGE 27
PCSC-Lite Copyright (c) 1999-2003 David Corcoran Copyright (c) 2001-2011 Ludovic Rousseau All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.