Gallagher T20 Terminal Installation Note T20 Alarms Terminal Black: C300463 T20 Alarms Terminal White: C300464 T20 PIV Reader Black: C305450 T20 PIV Reader White: C305451 T20 PIV Multi Tech Reader Black: C305460 T20 PIV Multi Tech Reader White: C305461 T20 Mifare Terminal Black: C300450 T20 Mifare Terminal White: C300451 T20 Multi Tech Terminal Black: C300460 T20 Multi Tech Terminal White: C300461 3E3140 Gallagher T20 Terminal Installation Note | Edition 16 | March 2016 Copyright © Gallagher Group Limited
Disclaimer This document gives certain information about products and/or services provided by Gallagher Group Limited or its related companies (referred to as "Gallagher Group"). The information is indicative only and is subject to change without notice meaning it may be out of date at any given time.
Contents 1 The Gallagher T20 Terminal.............................................................................................................. 4 2 Before you begin............................................................................................................................... 4 3 Distance between proximity readers................................................................................................ 7 4 Installation..........................................................
1 The Gallagher T20 Terminal The Gallagher T20 Terminal is available in a variety of variants. The variant you have purchased determines the available functionality and supported card technologies for the terminal. For variant details, refer to the "Terminal variants feature summary" on page 16 of this note. The Alarms Terminal variants (C300463 and C300464) are used for alarms management only, (i.e. do not contain a smart card proximity reader).
2.3 Cabling The Gallagher T20 Terminal requires a minimum cable size of 4 core 24 AWG (0.2 mm2) stranded security cable. This cable allows the transmission of data (2 wires) and power (2 wires). When using a single cable to carry both power supply and data, both the power supply voltage drop and data requirements must be considered. Although the terminal is specified to operate at 9 Vdc, for good engineering design it is recommended that the voltage at the terminal should be approximately 12 Vdc.
HBUS Device "T" or "Star" circuits are not permitted between HBUS devices Controller 6000 H1 H5 HBUS Device HBUS Device H4 H8 HBUS Device HBUS Module Terminate HBUS Device Terminate HBUS Device HBUS Device Terminate Terminate Cable distance Cable type Cable format* Single terminal connected using HBUS data only in a single cable Single terminal connected using Cardax IV data only in a single cable*** Single terminal connected using power and data in a single cable CAT 5e or better** 4 tw
3 Distance between proximity readers The distance separating any two proximity readers must not be less than 200 mm (8 in) in all directions. 200 mm When mounting a proximity reader on an internal wall, check that any reader fixed to the other side of the wall is not less than 200 mm (8 in) away. 200 4 mm Installation ATTENTION: This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing.
1. Are you installing the T20 Terminal on a Gallagher T20 Mounting Block? If no, then go to Step 2. If yes, then complete the following: A. If using the Duct Entry variant (C300931) of the T20 Mounting Block, take the cover off it. B. Mark the holes for the mounting screws on the mounting surface. C. Drill the holes for the mounting screws. D. Make a cabling hole in the Mounting Block and run the building cable through the hole, as demonstrated next.
When securing the base to a vertical, rectangular flush box, use the 6-32 UNC screws provided. When securing the base to a BS 4662 British Standard square flush box, use the M3.5 screws provided. Base M3.5 (40 mm) screw 6-32 (32 mm) screw 5. Drill pilot holes for the four corner fixing holes and the tamper tab. Secure the base to the mounting surface using the four corner fixing screws provided.
6. Connect the terminal tail extending from the facia assembly to the building cable. Connect the wires for the appropriate device you wish to interface, either an HBUS device or a Cardax IV device, as shown: Note: T20 Terminals using alarms management functionality and T20 PIV Readers must be connected as HBUS devices.
Base Facia Building cable Terminal tail Connection Fit T10 Torx Post screw to secure facia to base 9. Removal of the facia assembly is a simple reversal of these steps. 10. Configure the terminal in Command Centre. If the terminal is connected as an HBUS device, refer to the topic "Configuring an HBUS Terminal", "Configuring an HBUS Alarms Only Terminal" or "Configuring the PIV Card Reader" in the Command Centre Configuration Client Online Help.
• Gallagher GBUS Universal Reader Interface (Gallagher GBUS URI) • Gallagher Controller 3000-8R or 3000-4R • Gallagher Local Bus Universal Reader Interface (Gallagher URI) • Gallagher Local Bus Reader I/O Interface Refer to "Cardax IV Reader Connections" in the applicable installation note, for details regarding Cardax IV terminal connections. 6 HBUS LED indications LED (squiggle) Indication 3 Flash (Amber) No communications with the Controller.
8 9 T20 Terminal products T20 Terminals Product Code T20 Mifare Terminal, Black C300450 T20 Mifare Terminal, White C300451 T20 Multi Tech Terminal, Black C300460 T20 Multi Tech Terminal, White C300461 T20 Alarms Terminal, Black C300463 T20 Alarms Terminal, White C300464 T20 PIV Reader, Black C305450 T20 PIV Reader, White C305451 T20 PIV Multi Tech Reader, Black C305460 T20 PIV Multi Tech Reader, White C305461 T20 Terminal Accessories Product Code T20 Dress Plate, Black, Pk 5 C3003
10 Information screen To display the supported card technologies and the software version numbers of the terminal, press and hold the '#' key for 3 seconds. The Information screen is displayed.
12 Technical specifications Routine maintenance: Not applicable for this terminal. Cleaning: This terminal should be cleaned with mild soapy water only. Do not use solvents or abrasives. Voltage: 9 Vdc - 16 Vdc Current: Inactive 1 Active 2 T20 Mifare Terminal (at 9 Vdc): 191 mA 300 mA T20 Mifare Terminal (at 13.6 Vdc): 140 mA 200 mA T20 Multi Tech Terminal (at 9 Vdc): 262 mA 335 mA T20 Multi Tech Terminal (at 13.
3E3140 Gallagher T20 Terminal Installation Note | Edition 16 | March 2016 Copyright © Gallagher Group Limited Page 16 Terminal variants feature summary C300460 Access Control vHT1.0.69 C300461 C300463 None C300464 C305450 None C305451 C305460 C305461 T20 Multi Tech Terminal T20 Alarms Terminal T20 PIV Reader HBUS Alarms Management Supported From: vHT3.0 (vEL7.30) Access Control vHT2.01.02 (vEL7.21) vHT3.0 (vEL7.30) Alarms Management Alarms Management None Access Control vHT2.0.121 (vEL7.
14 Approvals and standards This symbol on the product or its packaging indicates that this product must not be disposed of with other waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
15 Mounting dimensions 95.7 mm (3.77 in) 70 mm (2.76 in) 110 mm (4.33 in) Cable Exit 40.65 mm (1.60 in) 83.3 mm (3.28 in) 60.3 mm (2.37 in) 60.3 mm (2.37 in) 58 mm (2.28 in) 179.5 mm (7.07 in) 29 mm (1.14 in) IMPORTANT This picture is not to scale, therefore use the measurements provided.
Open Source Software License Notice This product includes software code developed by third parties, including software code subject to the GNU General Public License (“GPL”), the GNU Library General Public License (“LGPL”), and a variety of additional licenses, including BSD-style licenses. As applicable, the terms of these licenses, and information on obtaining access to the open source code used in this product, are available for free download from https://security.gallagher.com/oss.
3.
Gnomovision version 69, Copyright (C) 19yy name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details. The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4.
12.If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13.
Finally, many people asked us for a preferred form for a credit/disclaimer to use in compliance with this license. We thus encourage you to use the following text: """ Portions of this software are copyright © The FreeType Project (www.freetype.org). All rights reserved. """ Please replace with the value from the FreeType version you actually use. Legal Terms =========== 0.
Copyright (c) 1997-2012 University of Cambridge All rights reserved. PCRE JUST-IN-TIME COMPILATION SUPPORT ------------------------------------Written by: Zoltan Herczeg Email local part: hzmester Emain domain: freemail.hu Copyright(c) 2010-2012 Zoltan Herczeg All rights reserved. STACK-LESS JUST-IN-TIME COMPILER -------------------------------Written by: Zoltan Herczeg Email local part: hzmester Emain domain: freemail.hu Copyright(c) 2009-2012 Zoltan Herczeg All rights reserved.
Copyright (c) 1993 The Regents of the University of California. strlcpy.c: Copyright (c) 1998 Todd C. Miller win32select.c: Copyright (c) 2003 Michael A. Davis evport.c: Copyright (c) 2007 Sun Microsystems ht-internal.h: Copyright (c) 2002 Christopher Clark minheap-internal.h: Copyright (c) 2006 Maxim Yegorushkin
