Gallagher T21 PIV Reader Installation Note T21 PIV Mifare Reader Black: C305500 T21 PIV Mifare Reader White: C305501 T21 PIV Multi Tech Reader Black: C305510 T21 PIV Multi Tech Reader White: C305511 3E4234 Gallagher T21 PIV Reader | Edition 1 | June 2016 Copyright © Gallagher Group Limited Page 1
Disclaimer This document gives certain information about products and/or services provided by Gallagher Group Limited or its related companies (referred to as "Gallagher Group"). The information is indicative only and is subject to change without notice meaning it may be out of date at any given time.
Contents 1 Introduction...................................................................................................................................... 4 2 Before you begin............................................................................................................................... 5 3 Distance between readers................................................................................................................ 7 4 Installation..........................................
1 Introduction The Gallagher T21 PIV Reader is available in four variants. The variant you have purchased determines the supported card technologies for the reader, refer to the topic "Reader variants feature summary" below. The reader's contact slot reads PIV card data, for PIV PIN validation. The reader contains an NXP chip for improved read range performance and supports Bluetooth® technology for hands-free access. The reader is compatible with the Gallagher Command Centre software vEL7.50 (or later).
2 Before you begin 2.1 Shipment contents Check the shipment contains the following items: 2.2 • 1 x Gallagher T21 Reader facia assembly • 1 x Gallagher T21 Reader bezel • 2 x 6-32 UNC (32 mm) Phillips drive fixing screws • 2 x M3.5 (40 mm) Phillips drive fixing screws • 5 x 25 mm No.6 self tapping, pan head, Phillips drive fixing screws • 5 x 40 mm No.
"T" or "Star" circuits are not permitted between HBUS devices HBUS Device HBUS Device HBUS Device HBUS Device HBUS Device Controller 6000 Connect the on-board termination jumper Terminate HBUS Device HBUS Device RS485 1 "T" or "Star" circuits are not permitted between HBUS devices HBUS Device RS485 1 HBUS Device Controller 6000 Terminate Remove the on-board termination jumper Terminate HBUS Device HBUS Device "T" or "Star" circuits are not permitted between HBUS devices Controller 6000
Cable distance Cable type Cable format* Single reader connected using HBUS data only in a single cable Single reader connected using power and data in a single cable CAT 5e or better** 4 twisted pair Each 2 x 0.2 mm2 (24 AWG) 500 m (1640 ft) 50 m (165 ft) BELDEN 9842** (shielded) 2 twisted pair Each 2 x 0.2 mm2 (24 AWG) 500 m (1640 ft) 50 m (165 ft) SEC472 4 x 0.2 mm2 Not twisted pairs (24 AWG) 400 m (1310 ft) 50 m (165 ft) SEC4142 4 x 0.
When mounting a proximity reader on an internal wall, check that any reader fixed to the other side of the wall is not less than 200 mm (8 in) away. 200 4 mm Installation ATTENTION: This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing.
Bezel M3.5 (40 mm) screw 4. 6-32 (32 mm) screw Drill pilot holes for the four corner fixing holes and the tamper tab. Secure the bezel to the mounting surface using the four corner fixing screws provided. Secure the tamper tab (located in the bezel) to the mounting surface using the remaining fixing screw provided. It is important the four corner fixing screws are used to ensure the reader is flush with and tight against the mounting surface.
5. The reader connects to a Gallagher Controller 6000 High Spec PIV, Gallagher 4H/8H HBUS Module (attached to the Controller 6000 High Spec PIV) or a Gallagher HBUS Door Module (connected to a Controller 6000 High Spec PIV). Unplug the reader's terminal block from the PCB. Connect the wires from the building cable to the terminal block as shown. Plug the terminal block back into the PCB.
Fit security screw to secure facia to bezel 9. Removal of the facia assembly is a simple reversal of these steps. Hint: After removal of the security screw, press the top of the facia. The bottom of the facia will exit the reader bezel. Alternatively, carefully use an electrical screwdriver to lever the bottom of the facia away from the bezel. 10. 5 Configure the reader in Command Centre.
7 LED indications LED (squiggle) Indication 3 Flash (Amber) No communications with the Controller. The terminal screen displays the text 'Connecting...'. 2 Flash (Amber) Communications with the Controller, but terminal is not configured. The terminal screen displays the text 'Not configured'. 1 Flash (Amber) Configured to a Controller, but terminal is not assigned to a door or elevator car.
9 Icons Insert Card Remove Card Armed Present Card Present Two Cards Enter PIN/Code Access Granted Access Denied Free Access Not Allowed Card or Code 3E4234 Gallagher T21 PIV Reader | Edition 1 | June 2016 Copyright © Gallagher Group Limited Page 13
10 Technical specifications Routine maintenance: Not applicable for this reader. Cleaning: This reader should be cleaned with mild soapy water only. Do not use solvents or abrasives. Voltage: 9 Vdc - 16 Vdc Current: Inactive 1 Active 2 T21 PIV Mifare Reader (at 9 Vdc): ??? mA ??? mA T21 PIV Mifare Reader (at 13.6 Vdc): ??? mA ??? mA T21 PIV Multi Tech Reader (at 9 Vdc): ??? mA ??? mA T21 PIV Multi Tech Reader (at 13.
11 Approvals and standards This symbol on the product or its packaging indicates that this product must not be disposed of with other waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
12 Mounting dimensions 95.8 mm (3.8 in) 70 mm (2.8 in) 20 mm (0.8 in) 40 mm (1.6 in) 60.3 mm (2.4 in) 83.3 mm (3.3 in) 231.9 mm (9.1 in) 45 mm (1.8 in) 102 mm (4 in) 29 mm (1.1 in) Cable exit within 1.8 x 1.6 inch hole (45 x 40 mm) 60.3 mm (2.4 in) IMPORTANT This picture is not to scale, therefore use the measurements provided.
Open Source Software License Notice This product includes software code developed by third parties, including software code subject to the GNU General Public License (“GPL”), the GNU Library General Public License (“LGPL”), and a variety of additional licenses, including BSD-style licenses. As applicable, the terms of these licenses, and information on obtaining access to the open source code used in this product, are available for free download from https://security.gallagher.com/oss.
3.
Gnomovision version 69, Copyright (C) 19yy name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details. The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4.
12.If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13.
Finally, many people asked us for a preferred form for a credit/disclaimer to use in compliance with this license. We thus encourage you to use the following text: """ Portions of this software are copyright © The FreeType Project (www.freetype.org). All rights reserved. """ Please replace with the value from the FreeType version you actually use. Legal Terms =========== 0.
Copyright (c) 1997-2012 University of Cambridge All rights reserved. PCRE JUST-IN-TIME COMPILATION SUPPORT ------------------------------------Written by: Zoltan Herczeg Email local part: hzmester Emain domain: freemail.hu Copyright(c) 2010-2012 Zoltan Herczeg All rights reserved. STACK-LESS JUST-IN-TIME COMPILER -------------------------------Written by: Zoltan Herczeg Email local part: hzmester Emain domain: freemail.hu Copyright(c) 2009-2012 Zoltan Herczeg All rights reserved.
Copyright (c) 1993 The Regents of the University of California. strlcpy.c: Copyright (c) 1998 Todd C. Miller win32select.c: Copyright (c) 2003 Michael A. Davis evport.c: Copyright (c) 2007 Sun Microsystems ht-internal.h: Copyright (c) 2002 Christopher Clark minheap-internal.h: Copyright (c) 2006 Maxim Yegorushkin
