User's Manual

ManualsBrandsGallagher Group ManualsElectronicsProx Readers T20 Mifare

Page 1

Document Code: 3E3140

Edion 3, April 2013

The Gallagher T20 Reader

The Gallagher T20 Reader is a smart card proximity reader. The reader can be

installed as either an entry reader or an exit reader.

The reader can be mounted on a rectangular 50 mm x 75 mm (2” x 3”) ush box, BS

4662 Brish Standard square ush box, or any solid at surface.

The Mifare reader reads: Mifare DESFire EV1, Mifare Plus and Mifare Classic cards.

The Mul Tech reader reads: Mifare DESFire EV1, Mifare Plus, Mifare Classic and 125

KHz cards.

The reader sends informaon to the Gallagher Controller and acts upon informaon

sent from the Gallagher Controller. The reader itself does not make any access

decisions.

The reader uses the Cardax IV communicaons protocol to communicate with the

Gallagher Controller. Refer to the “Connecons” topic later in this note, for details

regarding Cardax IV Reader connecons.

ATTENTION: This equipment contains components that can be damaged

by electrostac discharge. Ensure both you and the equipment are earthed

before beginning any servicing.

Installaon Note

Gallagher T20 Reader

Summary of content (13 pages)

PAGE 1
Installation Note Gallagher T20 Reader ATTENTION: This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing. The Gallagher T20 Reader The Gallagher T20 Reader is a smart card proximity reader. The reader can be installed as either an entry reader or an exit reader.
PAGE 2
Gallagher T20 Reader Installation Note IMPORTANT: Gallagher T20 Multi Tech readers only: Using dual technology 125/Mifare cards with Gallagher T20 Multi Tech readers may cause both card technologies to be read, resulting in double card badges and unusual reader feedback. Gallagher strongly recommends against using dual technology 125/Mifare cards with Gallagher Multi Tech readers for sites running pre-Command Centre v7.00 software. From Command Centre v7.
PAGE 3
Gallagher T20 Reader Installation Note Cable type Cable format* Single reader connected using data only in a single cable Single reader connected using power and data in a single cable CAT 5e or better 4 twisted pair Each 2 x 0.2 mm2 (24 AWG) 200 m (650 ft) 100 m (330 ft) BELDEN 9842 (shielded) 2 twisted pair Each 2 x 0.2 mm2 (24 AWG) 200 m (650 ft) 100 m (330 ft) SEC472 4 x 0.2 mm2 Not twisted pairs (24 AWG) 200 m (650 ft) 100 m (330 ft) SEC4142 4 x 0.
PAGE 4
Gallagher T20 Reader Installation Note Installation The Gallagher T20 Reader can be mounted on: • • • a vertical, rectangular 50 mm x 75 mm (2” x 3”) flush box a BS 4662 British Standard square flush box any solid flat surface The recommended mounting height for the reader is 1.1 m (3.6 ft) from the floor level to the centre of the reader device. However this may vary in some countries and you should check local regulations for variations to this height. Notes: • • • 1.
PAGE 5
Gallagher T20 Reader Installation Note 5. Secure the tamper tab (located in the base) to the mounting surface using remaining fixing screw provided. No. 6 pan head screw Base Tamper tab Building cable 6. Connect the reader tail extending from the facia assembly to the building cable. Connect the wires, as shown in the following diagram. Cardax IV Reader Note: Do not cut the “Reserved” wires, as they may be used for future functions.
PAGE 6
Gallagher T20 Reader Installation Note Base Facia Building cable Reader tail Connection Fit T10 Torx Post screw to secure facia to base 9. Removal of the facia assembly is a simple reversal of these steps. Note: If it is difficult to remove the facia from the base, a tab can be fashioned using a piece of gaffer tape. Stick the tab to the facia (over the Gallagher logo) and use it to pull the facia out of the base, then remove the tape without leaving a mark.
PAGE 7
Gallagher T20 Reader Installation Note Cardax IV Reader 1 Negative Positive Reserved Reserved Reserved CDXIV RX CDXIV TX Black Red Orange Green Brown Blue White Cardax IV Reader 2 Negative Positive Reserved Reserved Reserved CDXIV RX CDXIV TX Black Red Orange Green Brown Blue White C 4 5 6 C 1 2 3 R2 Out R2 In R1 Out R1 In + Gallagher Reader Module 8R or 4R (attached to the Controller 6000) Connect the wires to the sockets as shown: Gallagher Reader Module Gallagher GBUS Universal Reader Inte
PAGE 8
Gallagher T20 Reader Installation Note Gallagher Controller 3000-8R or 3000-4R The ports to which the Gallagher T20 Reader can connect are set up as groups: • • Four groups (numbered 1 to 4) on the Controller 3000-8R, and Two groups (numbered 1 and 2) on the Controller 3000-4R 1 VIN 0V SW OPEN 8 1 6 POWER IN P1 1 P1 P4 RS485 2 1 2 P3 P4 5 9 COMB COMA Each group provides connection for two readers. Refer to the following diagram for the location of the ports on the Controller 3000-8R.
PAGE 9
Gallagher T20 Reader Installation Note Make the connections from the reader to either the Controller 3000-8R or 3000-4R as shown: Gallagher Controller 3000-8R or 3000-4R Group PB4 and PA4 (3000-8R) PB2 and PA2 (3000-4R) PA Red Black Orange Green Brown White Blue Red Black Orange Green Brown White Blue Positive Negative Reserved Reserved Reserved CDXIV TX CDXIV RX Positive Negative Reserved Reserved Reserved CDXIV TX CDXIV RX 4 3 2 1 OUT 2 OUT 1 DATA 1 DATA 0 PB 2 0V 1 V OUT PB1 and PA1... to...
PAGE 10
Gallagher T20 Reader Installation Note HBUS LED Diagnostic Indications LED Diagnostic Indication 3 Flash (Amber) No communications with the Controller. On (Green or Red) Fully configured and functioning normally Green = Access mode is Free Red = Access mode is Secure Technical Specifications Routine maintenance: Not applicable for this reader. Cleaning: This reader should only be cleaned with a clean, lint free, damp cloth.
PAGE 11
Gallagher T20 Reader Installation Note Icons The Gallagher T20 Reader displays the following icons: Arming Failed Arming Succeeded Armed Present Card Present Second Card Enter PIN Access Granted Access Denied Wrong PIN Free Access Document Code: 3E3140 Edition 3, April 2013 Page 11
PAGE 12
Gallagher T20 Reader Installation Note Approvals and Standards FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications not expressly approved by Gallagher Limited could void the user’s authority to operate this equipment.
PAGE 13
Gallagher T20 Reader Installation Note Mounting Dimensions 95.7 mm (3.77 inches) 6G Screw 60.3 mm Flush Box Screw (2.37 inches) 83.3 mm (2.78 inches) 125 card read area 60.3 mm (2.37 inches) 179.5 mm (7.07 inches) 29.1 mm (1.14 inches) Cable Exit Mifare card read area IMPORTANT This picture is not to scale, therefore use the measurements provided.