User's Manual

ManualsBrandsGallagher Group ManualsElectronicsProx Readers T11 Mifare and T12 Mifare

Page 1

Part Number: 3E2513 | Edi on 10

November 2012

ATTENTION: This equipment contains components that can be damaged

by electrosta c discharge. Ensure both you and the equipment are earthed

before beginning any servicing.

The Gallagher T11 Reader

The Gallagher T11 Reader is a smart card proximity reader. It can be installed as

either an entry reader or exit reader. It can be mounted on a ver cal, rectangular

50 mm x 75 mm (2” x 3”) ﬂ ush box with moun ng holes spaced at a nominal 85 mm

(3.25”).

The Mifare reader reads: Mifare DESFire EV1, Mifare Plus and Mifare Classic cards.

The Mul Tech reader reads: Mifare DESFire EV1, Mifare Plus, Mifare Classic and

125 kHz cards.

The reader sends informa on to the Gallagher Controller and acts upon informa on

sent from the Gallagher Controller. The reader itself does not make any access

decisions.

The Gallagher T11 Reader uses the “Cardax IV Reader” communica ons protocol to

communicate with the Gallagher Controller.

Note: A French transla on of this document can be downloaded from the Gallagher

Support Site: hƩ p://support.gallagher.co

IMPORTANT: Gallagher T11 MulƟ Tech readers only:

Using dual technology 125/Mifare cards with Gallagher T11 Mul Tech readers

may cause both card technologies to be read, resul ng in double card badges

and unusual reader feedback. Gallagher strongly recommends against using dual

technology 125/Mifare cards with Gallagher Mul Tech readers for sites running

pre-Command Centre v7.00 so ware (due for release 2nd half, 2011). From

Command Centre v7.00, a site may specify which technology a Mul Tech reader

should read oﬀ a dual technology card.

InstallaƟ on Note

Gallagher T11 Reader

Summary of content (11 pages)

PAGE 1
InstallaƟon Note Gallagher T11 Reader ATTENTION: This equipment contains components that can be damaged by electrosta c discharge. Ensure both you and the equipment are earthed before beginning any servicing. The Gallagher T11 Reader The Gallagher T11 Reader is a smart card proximity reader. It can be installed as either an entry reader or exit reader. It can be mounted on a ver cal, rectangular 50 mm x 75 mm (2” x 3”) flush box with moun ng holes spaced at a nominal 85 mm (3.25”).
PAGE 2
Gallagher T11 Reader Installa on Note Before you begin Shipment Contents Check the shipment contains the following items: • • • • • • 1 x Gallagher T11 Reader facia assembly 1 x Gallagher T11 Reader base 1 x M3 Torx Post Security screw 2 x 6-32 UNC Phillips drive fixing screws 4 x 25 mm No.6 self tapping, pan head, Phillips drive fixing screws 4 x 40 mm No.
PAGE 3
Gallagher T11 Reader Installa on Note * The matching of wire sizes to equivalent wire gauges are only approximate. Grounding shielded cable may reduce the obtainable cable length by 25% to 30%. Distance between Proximity Readers The distance separa ng any two proximity readers must not be less than 200 mm (8 inches) in all direc ons. 200 mm When moun ng a proximity reader on an internal wall, check that any reader fixed to the other side of the wall is not less than 200 mm (8 inches) away.
PAGE 4
Gallagher T11 Reader Installa on Note If you are not moun ng to a flush box, secure the base to the moun ng surface using the four fixing screws provided. Base 6-32 UNC screw Building cable 6-32 UNC screw 4. Connect the reader tail extending from the facia assembly to the building cable. Connect the wires shown below. Cardax IV Reader Note: Do not cut the ‘Reserved’ wires, as these may be used for future func ons.
PAGE 5
Gallagher T11 Reader Installa on Note Facia Reader tail Connec on Fit screw to secure facia to base 7. Removal of the facia assembly is a simple reversal of these steps.
PAGE 6
Gallagher T11 Reader Installa on Note Cardax IV Reader 1 Nega ve Posi ve Reserved Reserved Reserved CDXIV RX CDXIV TX Black Red Orange Green Brown Blue White Cardax IV Reader 2 Nega ve Posi ve Reserved Reserved Reserved CDXIV RX CDXIV TX Black Red Orange Green Brown Blue White C 4 5 6 C 1 2 3 R2 Out R2 In R1 Out R1 In + ConnecƟng to the Gallagher Reader Module (for the Controller 6000) Connect the wires to the sockets as shown: Gallagher Reader Module ConnecƟng to the Gallagher GBUS Universal
PAGE 7
Gallagher T11 Reader Installa on Note ConnecƟng to the Gallagher Controller 3000-4R or 3000-8R The ports to which the Gallagher T11 Reader can connect are set up as groups, as follows: • • Two groups (numbered 1 and 2) on the Controller 3000-4R, and Four groups (numbered 1 to 4) on the Controller 3000-8R 0V 1 2 P1 POWER IN P1 VIN 5 9 COMA P3 P4 RS485 1 SW OPEN 8 1 6 1 P4 2 COMB Each group provides connec on for two Gallagher T11 Readers.
PAGE 8
Gallagher T11 Reader Installa on Note Make the connec ons from the Gallagher T11 Reader to either the Gallagher Controller 3000-4R or 3000-8R as shown: Gallagher Controller 3000-4R or 3000-8R Group PB2 and PA2 (3000-4R) PB4 and PA4 (3000-8R) PA Red Black Orange Green Brown White Blue Red Black Orange Green Brown White Blue Posi ve Nega ve Reserved Reserved Reserved CDXIV TX CDXIV RX Posi ve Nega ve Reserved Reserved Reserved CDXIV TX CDXIV RX 4 3 2 1 OUT 2 OUT 1 DATA 1 DATA 0 PB 2 0V 1 V OUT PB1
PAGE 9
Gallagher T11 Reader Installa on Note Technical SpecificaƟons Technical SpecificaƟons Rou ne maintenance: Not applicable for this reader. Cleaning: This reader should only be cleaned with a clean, lint free, damp cloth.
PAGE 10
Gallagher T11 Reader FCC Installa on Note This device complies with part 15 of the FCC Rules. Opera on is subject to the following two condi ons: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera on. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 11
32 mm (1.26 inches) 22.5 mm (0.89 inches) 40 mm (1.57 inches) 70 mm (2.76 inches) 115 mm (4.53 inches) 13 mm (1/2 inch) diameter hole for cable 40 mm (1.57 inches) 48 mm (1.