User's Manual

ManualsBrandsGallagher Group ManualsElectronicsProx Reader T11 Multi Tech and T12 Multi Tech

Part Number: 3E2513 R1 | 1

Installation Note | Gallagher T11 Reader

Installation Note

Gallagher T11 Reader

The Gallagher T11 Reader

The Gallagher T11 Reader is a smart card proximity reader. It can be installed as

either an entry reader or exit reader. It can be mounted on any standard electrical

flush (gang) box, used in New Zealand, Australia, USA and Canada.

The reader can read Mifare DESFire EV1, Mifare Plus and Mifare Classic cards. The

Multi Tech variant can also read 125Khz cards.

The reader sends information to the Cardax FT Controller and acts upon information

sent from the Cardax FT Controller. The reader itself does not make any access

decisions.

The Gallagher T11 Reader uses the “Cardax IV Reader” communications protocol

to communicate with the Cardax FT Controller.

This equipment contains components that can be damaged by electrostatic

discharge. Ensure both you and the equipment are earthed before beginning

any servicing.

Summary of content (11 pages)

PAGE 1
Installation Note | Gallagher T11 Reader Installation Note Gallagher T11 Reader This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing. The Gallagher T11 Reader The Gallagher T11 Reader is a smart card proximity reader. It can be installed as either an entry reader or exit reader. It can be mounted on any standard electrical flush (gang) box, used in New Zealand, Australia, USA and Canada.
PAGE 2
Installation Note | Gallagher T11 Reader Before you begin Shipment Contents Check the shipment contains the following items: • 1 x Gallagher T11 Reader facia assembly • 1 x Gallagher T11 Reader base • 1 x M3 Torx Post Security screw • 2 x 6-32 UNC screws • 4 x self tapping, pan head, pozi fixing screws Power Supply The Gallagher T11 Reader is designed to operate over a supply voltage range of 9 - 16Vdc measured at the reader terminals.
PAGE 3
Installation Note | Gallagher T11 Reader * The matching of wire sizes to equivalent wire gauges are only approximate. Note: Grounding shielded cable may reduce the obtainable cable length by 25% to 30%. Distance between Proximity Readers The distance separating any two proximity readers must not be less than 200mm (8 inches) in all directions. 200mm When mounting a proximity reader on an internal wall, check that any reader fixed to the other side of the wall is not less than 200mm (8 inches) away.
PAGE 4
Installation Note | Gallagher T11 Reader 3. Secure the base to the flush box using the two 6-32 UNC screws provided. It is important the base of the reader is flush with and tight against the mounting surface. If you are not mounting to a flush box, secure the base to the mounting surface using the four fixing screws provided. Base 6-32 UNC screw Building cable 6-32 UNC screw 4. Connect the reader tail extending from the facia assembly to the building cable. Connect the wires shown below.
PAGE 5
Installation Note | Gallagher T11 Reader Facia Reader tail Connection 7. Fit screw to secure facia to base Removal of the facia assembly is a simple reversal of these steps.
PAGE 6
Installation Note | Gallagher T11 Reader Connecting to the Cardax FT Reader Module (for the Controller 6000) C 4 5 6 C 1 2 3 Red Black Orange Green Brown White Blue R2 Out R2 In Positive Negative Reserved Reserved Reserved CDXIV TX CDXIV RX R1 Out R1 In Red Black Orange Green Brown White Blue + Cardax IV Reader 2 Positive Negative Reserved Reserved Reserved CDXIV TX CDXIV RX Cardax IV Reader 1 Connect the wires to the sockets as shown: Cardax FT Reader Module Connecting to the Cardax FT GBUS
PAGE 7
Installation Note | Gallagher T11 Reader Connecting to the Cardax FT Controller 3000-4R or 3000-8R The ports to which the Gallagher T11 Reader can connect are set up as groups, as follows: • Two groups (numbered 1 and 2) on the Controller 3000-4R, and • Four groups (numbered 1 to 4) on the Controller 3000-8R Each group provides connection for two Gallagher T11 Readers. Refer to the following diagram for the location of the ports on the Cardax FT Controller 3000-8R.
PAGE 8
Installation Note | Gallagher T11 Reader Make the connections from the Gallagher T11 Reader to either the Cardax FT Controller 3000-4R or 3000-8R as shown: Cardax FT Controller 3000-4R or 3000-8R Group PB1 and PA1... to...
PAGE 9
Installation Note | Gallagher T11 Reader Technical Specifications Technical Specifications Routine maintenance: Not applicable for this reader Cleaning: This reader should only be cleaned with a clean, lint free, damp cloth Power required: Voltage: 9Vdc - 16Vdc Current (at 12Vdc): 54mA (standby) Standard variant 100mA (peak) Standard variant 88mA (standby) Multi Tech variant 140mA (peak) Multi Tech variant Temperature Range: -30°C to +70°C Note: Direct sunlight may increase the internal reader temperature
PAGE 10
Installation Note | Gallagher T11 Reader FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 11
22.5mm (0.89 inches) 40mm (1.57 inches) 70mm (2.76 inches) 115mm (4.53 inches) 13mm (1/2 inch) diameter hole for cable 40mm (1.57 inches) 36mm (1.42 inches) 44mm (1.