User's Manual

ManualsBrandsGallagher Group ManualsElectronicsProx Reader T10 Mifare

Part Number: 3E2453 R1 | 1

Installation Note | Gallagher T10 Mifare Reader

Installation Note

Gallagher T10 Mifare Reader

The Gallagher T10 Mifare Reader

The Gallagher T10 Mifare reader is a smart card proximity reader. It can

be installed as either an entry reader or exit reader.

The reader can read Mifare DESFire EV1, Mifare Plus and Mifare Classic

cards.

The reader sends information to the Cardax FT Controller and acts upon

information sent from the Cardax FT Controller. The reader itself does not

make any access decisions.

The Gallagher T10 Mifare reader uses the “Cardax IV Reader”

communications protocol to communicate with the Cardax FT Controller.

This equipment contains components that can be damaged by

electrostatic discharge. Ensure both you and the equipment are

earthed before beginning any servicing.

Summary of content (11 pages)

PAGE 1
Installation Note | Gallagher T10 Mifare Reader Installation Note Gallagher T10 Mifare Reader This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing. The Gallagher T10 Mifare Reader The Gallagher T10 Mifare reader is a smart card proximity reader. It can be installed as either an entry reader or exit reader. The reader can read Mifare DESFire EV1, Mifare Plus and Mifare Classic cards.
PAGE 2
Installation Note | Gallagher T10 Mifare Reader Before you begin Shipment Contents Check the shipment contains the following items: • • • • • 1 x Gallagher T10 Mifare reader facia assembly 1 x Gallagher T10 Mifare reader base 1 x Gallagher T10 Mifare reader installation note 1 x M3 Torx Post Security screw 2 x self tapping pan head pozi fixing screws Power Supply The Gallagher T10 Mifare reader receives power from the device to which it is connected.
PAGE 3
Installation Note | Gallagher T10 Mifare Reader Cable type Combined power and data in a single cable CAT5e SEC472 (4 x 0.2mm2) SEC4142 (4 x 0.4mm2) BELDEN 8723 (22 AWG) BELDEN 9842 (24 AWG) 100m 100m 100m 152m 152m (320ft) (320ft) (320ft) (500ft) (500ft) Distance between Proximity Readers The distance separating any two proximity readers must not be less than 200mm (8 inches) in all directions.
PAGE 4
Installation Note | Gallagher T10 Mifare Reader 1. Using the drill template at the back of this installation note as a guide, drill all three holes. Drill the 13mm (1/2 inch) diameter centre hole (this is the centre hole for which the building cable will exit the mounting surface) and the two fixing holes. 2. Run the building cabling out through the centre hole and through the reader base. 3. Secure the base to the mounting surface using the two fixing screws provided.
PAGE 5
Installation Note | Gallagher T10 Mifare Reader 6. Insert the M3 Torx Post Security screw (using a T10 Torx Post Security screwdriver) through the hole at the bottom of the base to secure the facia assembly. Note: The recommended torque for the security screw is 0.7Nm (0.5 lb/ft). It is important not to exceed the maximum torque of 1.5Nm (1.1 lb/ft). Facia Reader tail Building cable Connection 7. Fit screw to secure facia to base Removal of the facia assembly is a simple reversal of these steps.
PAGE 6
Installation Note | Gallagher T10 Mifare Reader Connecting to the Cardax FT Reader Module (for the Controller 6000) C 4 5 6 C 1 2 3 Red Black Orange Green Brown White Blue R2 Out R2 In Positive Negative Reserved Reserved Reserved CDXIV TX CDXIV RX R1 Out R1 In Red Black Orange Green Brown White Blue + Cardax IV Reader 2 Positive Negative Reserved Reserved Reserved CDXIV TX CDXIV RX Cardax IV Reader 1 Connect the wires to the sockets as shown: Cardax FT Reader Module Connecting to the Cardax F
PAGE 7
Installation Note | Gallagher T10 Mifare Reader Connecting to the Cardax FT Controller 3000-4R or 3000-8R The Cardax FT Controller 3000-4R can interface up to four Gallagher T10 Mifare readers into the Cardax FT Command Centre system. The Cardax FT Controller 3000-8R can interface up to eight Gallagher T10 Mifare readers into the Cardax FT Command Centre system.
PAGE 8
Installation Note | Gallagher T10 Mifare Reader Make the connections from the Gallagher T10 Mifare reader to either the Cardax FT Controller 3000-4R or 3000-8R as shown: Cardax FT Controller 3000-4R or 3000-8R Group PB1 and PA1... to...
PAGE 9
Installation Note | Gallagher T10 Mifare Reader Technical Specifications Technical Specifications Routine maintenance Not applicable for this reader Cleaning This reader should only be cleaned with a clean, lint free, damp cloth Power required Voltage: 9Vdc - 16Vdc Current: 40mA (at 16Vdc) 70mA (at 9Vdc) The current will increase momentarily during a card read, beeper and LED activity: 120mA (at 12Vdc) Environmental Operating temperature: -30°C to +70°C Note: Direct sunlight may increase the internal reade
PAGE 10
Installation Note | Gallagher T10 Mifare Reader FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 11
40mm (1.57 inches) 13mm (1/2 inch) diameter hole for cable 40mm (1.57 inches) 44mm (1.73 inches) 115mm (4.53 inches) Drill Template 22.5mm (0.89 inches) 35mm (1.