User's Manual

ManualsBrandsGallagher Group ManualsElectronicsProx Reader Mifare (Teardrop)

Installation Note

Part number 3E1100 R12 1

June 2007

CAUTION

This equipment contains components that can be damaged by

electrostatic discharge. Ensure both you and the equipment are

earthed before beginning any servicing.

Before you Begin

Unpack the Prox Mifare Series (Teardrop) reader and check the shipment

contains the following items:

• 1 x Prox Mifare Series (Teardrop) reader base

• 1 x Prox Mifare Series (Teardrop) reader facia

• 1 x printed circuit board (PCB) assembly

• 1 x cable assembly

• 1 x M3 Torx Post Security screw

• 4 x self tapper pozi counter sunk fixing screws (two different lengths)

WARNING: You must use the screws provided, as using other types of

screws could interfere with the electronics. (See the “Mounting” section

later for further explanation.)

Power Supply Requirements

Power for the Prox Mifare Series (Teardrop) reader is usually taken from the

incoming supply of the device to which it is connected. That is, from the:

• Cardax FT Reader I/O Interface

• Cardax FT Controller 3000

• Cardax FT Universal Reader Interface (Cardax FT URI)

• Cardax Commander Universal Reader Interface (Cardax Commander URI).

The supply at the reader should be 13.6 V DC ± 15%. The current draw is 180

mA per reader. This is in addition to the requirements of any other device (for

example, the URI) powered from the same supply.

Prox Mifare Series (Teardrop)

Summary of content (18 pages)

PAGE 1
Installation Note Prox Mifare Series (Teardrop) CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing.
PAGE 2
Prox Mifare Series (Teardrop) readers require a good quality linear power source. If you do not use the recommended power supply, it may affect the performance of the reader. Note: Switch mode power supplies are not recommended as they may reduce the read range of the Prox Mifare Series (Teardrop) reader. Cabling The Prox Mifare Series (Teardrop) reader uses the Cardax IV communications system.
PAGE 3
Please note that 200mm in all directions includes the distance through walls. Proximity Reader Proximity Reader Wall Less than 200mm thick Mounting Note: The Prox Mifare Series (Teardrop) reader has been designed to metric specifications. Therefore any imperial measurements provided are approximate only. The Prox Mifare Series (Teardrop) reader is designed to be mounted on any solid flat surface.
PAGE 4
mounting surface to a minimum depth of 40 mm (11/2 in). Drill two pilot holes for the fixing screws. Run the building cabling through the base and grommet. Fit the base to the 20 mm (3/4 inch) hole and secure it to the mounting surface using two of the fixing screws provided. Note: The surface the reader is being attached to will determine which length screws are most appropriate from those provided. WARNING: You must use the screws provided, taking care not to overtighten them.
PAGE 5
to secure the base. Push the socket back into the grommet. Push the grommet and socket back into the Prox Mifare Series (Teardrop) reader base. Check the tape covering the antenna wire solder joints is in position. Install the PCB assembly into the base, ensuring the connector on the back of the PCB assembly fits into the socket in the base. The PCB assembly should click into place.
PAGE 6
Connections The Prox Mifare Series (Teardrop) reader connects to one of the following: • Cardax FT Controller 3000 • Cardax FT Reader I/O Interface • Cardax FT URI • Cardax Commander URI Use the cable terminating tool to connect the cables to the socket as described in the following sections. Pin number 4 of the Prox Mifare Series (Teardrop) reader connector feeds into the cable terminating tool first.
PAGE 7
Make the connections from the Prox Mifare Series (Teardrop) reader to the Cardax FT Controller 3000 as shown: Controller 3000 Group (x4) PB1 and PA1... to... PB4 and PA4 PB 4 3 Prox Plus Mifare Reader 2 PA 2 1 2 1 Prox Plus Mifare Reader 1 Note: Within each group, you cannot mix Cardax IV readers with Wiegand Readers. This is because connecting one Wiegand reader requires all four pins on plug PB.
PAGE 8
Connecting to the Cardax FT Reader I/O Interface The Cardax FT Reader I/O Interface has connections for up to sixteen Prox Mifare Series (Teardrop) readers or other Cardax IV readers. The Prox Mifare Series (Teardrop) reader connects to either plug PA or PB in Groups 1 to 8.
PAGE 9
Connecting to the Cardax FT URI Connect the cables to the socket as shown. Cardax FT Universal Reader Interface Prox Plus Mifare Connector Plug P1 or P2 Black 4 GND Blue 3 OUTPUTS White 2 OUTPUTS Red 1 DET COMMS COMMS 5/12V Connect the Prox Mifare Series (Teardrop) reader connector to either the P1 or P2 plug on the Cardax FT URI. Refer to the Cardax FT URI component layout diagram, next, for the location of the plugs. F1 P3 13.
PAGE 10
Connecting to the Cardax Commander URI Connect the cables to the socket as shown in the following diagram. Universal Reader Interface Prox Plus Mifare Connector 4 3 2 1 Black Blue White Red Plug P4 (Exit) or P5 (Entry) 1 GND 2 BPR 3 LED 4 DET 5 1-CK 6 0-DT 7 5/12V Note: Refer to Cardax Commander URI Components, for the location of the Cardax Commander URI components.
PAGE 11
Initialisation Initialising with the Cardax FT Controller 3000 Refer to the Cardax FT Controller 3000 Installation Note (Part number 3E1089) for initialisation instructions. Initialisation of the Cardax FT Controller 3000 does not require prior connection to the Prox Mifare Series (Teardrop) reader. The Prox Mifare Series (Teardrop) reader will be operational as soon as it is: • connected to a Cardax FT Controller 3000, and • configured as a Cardax IV reader within the Cardax FT Command Centre system.
PAGE 12
Note: If you are installing the Prox Mifare Series (Teardrop) reader to control a turnstile you should consult the turnstile manufacturer for details of the locking mechanism used. Push-Button Exit If the door has a push button exit, ensure the URI Exit terminal has the pushbutton fitted and correctly terminated with a 10 k resistor before you power on. Check Software Version You should check the URI software version to ensure it is correct for your installation.
PAGE 13
Cardax Commander URI Components Please refer to the diagram below for the location of the Cardax Commander URI components. Fuse Fuses (Reader Power (Relay Supply) Contacts) Comms & Power Ground COM B COM A Power P1 Lithium Battery Lithium Battery Jumper J1 D8 D45 Comms In F1 F2 D10 5 V DC P8 F3 P2 P7 Door 1 Keypad Comms Out Ground GND Normally Open N.O. Relay Common COM Normally Closed N.C.
PAGE 14
Setting the Jumpers Tamper the URI by opening the door of the cabinet. This releases the tamper switch. The URI has a set of six jumpers grouped into two sets of three. One group is labelled ENTRY and the other is labelled EXIT. ENTRY jumpers set the voltage and card type of the reader connected to plug P5. EXIT jumpers set the voltage and card type of the reader connected to plug P4.
PAGE 15
Setting the Dip Switches Set DIPSW1 as follows: Switches 1 2 3 4 5 6 7 8 On 1 2 4 8 16 32 Off Unit Addresses Initialise 1 door software = liftcar reader 2 door software = keypad on door 2 Normal 1 door software = door reader 2 door software = no keypad on door 2 Set DIPSW2 as follows, where 0 = OFF and 1 = ON: URI Software vW6.xx and vW9.xx vW3.61 to vW3.67 and vW4.74 to vW4.
PAGE 16
Initialise Process ! CAUTION Do not fit the lithium battery jumper (J1) before powering up the URI. If the jumper is fitted you must remove it and wait 10 seconds. Power up the URI. The yellow LED (D45) should be permanently ON. This indicates that 5 V is present on the board. The green LED (D44) should flash twice, pause, then flash twice again. This is a continuous sequence while the URI is unitialised and indicates it is processing.
PAGE 17
Technical specification Note: All specifications are subject to appropriate installation. Routine maintenance and serviceable parts: Not applicable for a Cardax Prox Mifare Series (Teardrop) reader Cleaning: The Cardax Prox Mifare Series (Teardrop) reader should only be cleaned with clean, lint free, damp cloth Power required: Voltage Current 13.
PAGE 18
Mounting Dimensions Pilot hole Slot 20 mm hole 39 mm 20 mm 51 mm 45 mm Pilot hole 17 mm 18 Part number 3E1100 R12 June 2007