GS2011MIPS User Manual GS2011MIPS An IEEE 802.11b/g/n Low-Power Wireless System-On-Chip module User Manual Sheet 1 of 18 July.
GS2011MIPS This document describes a simple method for characterizing GS2011MIPS WLAN module based RF parameters, such as transmitted spectra and receiver sensitivity. It will be described step by step below that how to control and setup. Step 1 : Extract to CDM20814_WHQL_Certified.zip, it is a USB to UART driver, then setup it. Step 2 : Setup teraterm_utf8-4.58.exe program, this program can help to send command to module.
GS2011MIPS Step 6 : Now any legal command can be keyed in and if UTF-8 reply ok, the command is implemented successful like below figure. Figure 3 802.
GS2011MIPS at+wrfteststart at+wtx100test=1,0,9,0,0,0,0,1,1,0,0,1,1,1 at+wtx100test=6,0,9,0,0,0,0,1,1,0,0,1,1,1 at+wtx100test=11,0,9,0,0,0,0,1,1,0,0,1,1,1 At+rfset Start up internal Power Amplifier Continuous Tx Channel 1, 2Mbps Continuous Tx Channel 6, 2Mbps Continuous Tx Channel 11, 2Mbps Transmitter off Transmitted Tx at 1Mbps at+wrfteststart at+wtx100test=1,0,18,0,0,0,0,1,1,0,0,1,0,1 at+wtx100test=6,0,18,0,0,0,0,1,1,0,0,1,0,1 at+wtx100test=11,0,18,0,0,0,0,1,1,0,0,1,0,1 At+rfset Start up internal Power
GS2011MIPS at+wtx100test=1,0,26,0,0,0,0,1,0,0,0,1,1,0 at+wtx100test=6,0,26,0,0,0,0,1,0,0,0,1,1,0 at+wtx100test=11,0,26,0,0,0,0,1,0,0,0,1,1,0 At+rfset Continuous Tx Channel 1, 24Mbps Continuous Tx Channel 6, 24Mbps Continuous Tx Channel 11, 24Mbps Transmitter off Transmitted Tx at 18Mbps Command at+wrfteststart at+wtx100test=1,0,27,0,0,0,0,1,0,0,0,1,6,0 at+wtx100test=6,0,27,0,0,0,0,1,0,0,0,1,6,0 at+wtx100test=11,0,27,0,0,0,0,1,0,0,0,1,6,0 At+rfset Action Start up internal Power Amplifier Continuous Tx Cha
GS2011MIPS at+wtx100test=1,0,18,0,0,0,0,1,0,0,0,1,7,2 at+wtx100test=6,0,18,0,0,0,0,1,0,0,0,1,7,2 at+wtx100test=11,0,18,0,0,0,0,1,0,0,0,1,7,2 At+reset Continuous Tx Channel 1, 72Mbps Continuous Tx Channel 6, 72Mbps Continuous Tx Channel 11, 72Mbps Transmitter off Transmitted Tx at MCS6 at+wrfteststart at+wtx100test=1,0,20,0,0,0,0,1,0,0,0,1,6,2 at+wtx100test=6,0,20,0,0,0,0,1,0,0,0,1,6,2 at+wtx100test=11,0,20,0,0,0,0,1,0,0,0,1,6,2 At+reset Start up internal Power Amplifier Continuous Tx Channel 1, 65Mbps Co
GS2011MIPS Transmitted Tx at MCS1 at+wrfteststart at+wtx100test=1,0,27,0,0,0,0,1,0,0,0,1,1,2 at+wtx100test=6,0,27,0,0,0,0,1,0,0,0,1,1,2 at+wtx100test=11,0,27,0,0,0,0,1,0,0,0,1,1,2 At+reset Start up internal Power Amplifier Continuous Tx Channel 1, 14.4Mbps Continuous Tx Channel 6, 14.4Mbps Continuous Tx Channel 11, 14.
GS2011MIPS Device Pin-out Diagram (Module top view) User Manual Sheet 8 of 18 July.
GS2011MIPS DFWM-GIB0x Device Pin-out Diagram (Module top view) Module Pins Description User Manual Sheet 9 of 18 July.
GS2011MIPS User Manual Sheet 10 of 18 July.
GS2011MIPS User Manual Sheet 11 of 18 July.
GS2011MIPS User Manual Sheet 12 of 18 July.
GS2011MIPS Antenna Information Frequency range Peak gain PCB Antenna 2400 MHz – 2500 MHz -3.06 dBi EIRP(2450MHz)-XY cut EIRP(2450MHz)-XZ cut User Manual Sheet 13 of 18 July.
GS2011MIPS EIRP(2450MHz)-YZ cut Antenna Location User Manual Sheet 14 of 18 July.
GS2011MIPS Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
GS2011MIPS Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
GS2011MIPS compliance could void the user’s authority to operate the equipment. Section 15.105 (a) for Class A Device For a Class A digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual: NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
GS2011MIPS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. End Product Labeling: The final end product must be labeled in a visible area with the following: “Contains FCC ID: YOPGS2011MIPS”.
