GS2011MIES User Manual GS2011MIES An IEEE 802.11b/g/n Low-Power Wireless System-On-Chip module User Manual Sheet 1 of 17 July.
GS2011MIES This document describes a simple method for characterizing GS2011MIES WLAN module based RF parameters, such as transmitted spectra and receiver sensitivity. It will be described step by step below that how to control and setup. Step 1 : Extract to CDM20814_WHQL_Certified.zip, it is a USB to UART driver, then setup it. Step 2 : Setup teraterm_utf8-4.58.exe program, this program can help to send command to module.
GS2011MIES Step 6 : Now any legal command can be keyed in and if UTF-8 reply ok, the command is implemented successful like below figure. Figure 3 802.
GS2011MIES at+wrfteststart at+wtx100test=1,0,9,0,0,0,0,1,1,0,0,1,1,1 at+wtx100test=6,0,9,0,0,0,0,1,1,0,0,1,1,1 at+wtx100test=11,0,9,0,0,0,0,1,1,0,0,1,1,1 At+reset Start up internal Power Amplifier Continuous Tx Channel 1, 2Mbps Continuous Tx Channel 6, 2Mbps Continuous Tx Channel 11, 2Mbps Transmitter off Transmitted Tx at 1Mbps at+wrfteststart at+wtx100test=1,0,18,0,0,0,0,1,1,0,0,1,0,1 at+wtx100test=6,0,18,0,0,0,0,1,1,0,0,1,0,1 at+wtx100test=11,0,18,0,0,0,0,1,1,0,0,1,0,1 At+reset Start up internal Power
GS2011MIES at+wtx100test=1,0,26,0,0,0,0,1,0,0,0,1,1,0 at+wtx100test=6,0,26,0,0,0,0,1,0,0,0,1,1,0 at+wtx100test=11,0,26,0,0,0,0,1,0,0,0,1,1,0 At+reset Continuous Tx Channel 1, 24Mbps Continuous Tx Channel 6, 24Mbps Continuous Tx Channel 11, 24Mbps Transmitter off Transmitted Tx at 18Mbps Command at+wrfteststart at+wtx100test=1,0,27,0,0,0,0,1,0,0,0,1,6,0 at+wtx100test=6,0,27,0,0,0,0,1,0,0,0,1,6,0 at+wtx100test=11,0,27,0,0,0,0,1,0,0,0,1,6,0 At+reset Action Start up internal Power Amplifier Continuous Tx Cha
GS2011MIES at+wtx100test=1,0,18,0,0,0,0,1,0,0,0,1,7,2 at+wtx100test=6,0,18,0,0,0,0,1,0,0,0,1,7,2 at+wtx100test=11,0,18,0,0,0,0,1,0,0,0,1,7,2 At+reset Continuous Tx Channel 1, 72Mbps Continuous Tx Channel 6, 72Mbps Continuous Tx Channel 11, 72Mbps Transmitter off Transmitted Tx at MCS6 at+wrfteststart at+wtx100test=1,0,20,0,0,0,0,1,0,0,0,1,6,2 at+wtx100test=6,0,20,0,0,0,0,1,0,0,0,1,6,2 at+wtx100test=11,0,20,0,0,0,0,1,0,0,0,1,6,2 At+reset Start up internal Power Amplifier Continuous Tx Channel 1, 65Mbps Co
GS2011MIES Transmitted Tx at MCS1 at+wrfteststart at+wtx100test=1,0,27,0,0,0,0,1,0,0,0,1,1,2 at+wtx100test=6,0,27,0,0,0,0,1,0,0,0,1,1,2 at+wtx100test=11,0,27,0,0,0,0,1,0,0,0,1,1,2 At+reset Start up internal Power Amplifier Continuous Tx Channel 1, 14.4Mbps Continuous Tx Channel 6, 14.4Mbps Continuous Tx Channel 11, 14.
GS2011MIES Device Pin-out Diagram (Module top view) DFWM-GIB0x Device Pin-out Diagram (Module top view) User Manual Sheet 8 of 17 July.
GS2011MIES Module Pins Description User Manual Sheet 9 of 17 July.
GS2011MIES User Manual Sheet 10 of 17 July.
GS2011MIES User Manual Sheet 11 of 17 July.
GS2011MIES Antenna Information RFA-02-P33-70B-150 Frequency 2400 MHz – 2500 MHz range Peak gain 2 dBi Average 1 dBi gain VSWR 2.0 : 1 Max. Radiated pattern RFA-02-L2H1 2400 MHz – 2500 MHz 2.5 dBi 2.0 : 1 Max. H-Plane V-Plane User Manual Sheet 12 of 17 July.
GS2011MIES Location include User Manual Sheet 13 of 17 July.
GS2011MIES Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
GS2011MIES Canada, avis d'Industry Canada (IC) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
GS2011MIES You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. Section 15.
GS2011MIES Part 15.19(a)(3) unlicensed project (WLAN Device) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. End Product Labeling: The final end product must be labeled in a visible area with the following: “Contains FCC ID: YOPGS2011MIES”.
