GS1011MIES User Manual GS1011MIES An IEEE 802.11b Low-Power Wireless System-On-Chip module User Manual Sheet 1 of 12 Mar.
GS1011MIES This document describes a simple method for characterizing GS1011MIES WLAN module based RF parameters, such as transmitted spectra and receiver sensitivity. It will be described step by step below that how to control and setup. Step 1 : Extract to CDM20814_WHQL_Certified.zip, it is a USB to UART driver, then setup it. Step 2 : Setup teraterm_utf8-4.58.exe program, this program can help to send command to module.
GS1011MIES Figure 3 A series of legal command: Internal PA Transmitted Transmitted Tx at 11Mbps for every channel Command at+extpa=0 at+rfwavetxstart=1,1,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,2,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,3,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,4,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,5,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,6,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,7,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,8,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,9,3,1,
GS1011MIES Transmitted Tx at 5.
GS1011MIES at+rfwavetxstart=1,2,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,3,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,4,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,5,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,6,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,7,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,8,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,9,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,10,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,11,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,12,0,1,0,1,0,GainSpanDemo at+rfwavetxsta
GS1011MIES Antenna Information RFA-02-P05-70B-150 Frequency 2400 MHz – 2500 MHz range Peak gain 2 dBi Average 2.0 : 1 Max. gain VSWR Linear, vertical Radiated pattern RFA-02-5-F7H1-70B150 2400 MHz – 2500 MHz 5 dBi 2.0 : 1 Max. Linear, vertical H-Plane V-Plane User Manual Sheet 6 of 12 Mar.
GS1011MIES Location include User Manual Sheet 7 of 12 Mar.
GS1011MIES Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits.
GS1011MIES Canada, avis d'Industry Canada (IC) Cet appareil et RSS-210. numérique de classe B est conforme aux normes canadiennes ICES-003 Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.
GS1011MIES Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. Section 15.
GS1011MIES Part 15.19(a)(3) unlicensed project (WLAN Device) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. End Product Labeling: The final end product must be labeled in a visible area with the following: “Contains FCC ID: YOPGS1011MIES”.
GS1011MIES User manuals for transmitters equipped with detachable antennas shall also contain the following notice in a conspicuous location: This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
