Specification Sheet

VG 491 211CA
Stainless steel
Width 36" (90 cm)
Natural gas.
For conversion to LP gas, LP kit
(part #10004447) must be ordered.
Included accessories
1 wok attachment ring
Installation accessories
In combination of several Vario
cooktops, connecting strips must be
used. Choose respective VA 420 strip
from one of the below, depending on
type of installation.
VA 420 000
Connection strip for combination
with other Vario 400 series for
flush mounting.
VA 420 010
Connection strip for combination
with other Vario 400 series for
surface mounting.
Optional accessories
WP 400 001
Wok pan made of multiple-layer
material with round bottom and handle
ø 14 ³⁄₁₆", 6.3 qt., height 4".
Combinable with:
AL400791
AI442720 / AI442760
AW442720 / AW442760
Good to know:
Wall installations require the hood to
be as large as the cooktop(s). Island
installations require the hood to be
larger than the cooktop(s).
Vario 400 series gas cooktop
VG 491
– Five multi-ring burners with up to
59,700 BTU
– Full electronic power regulation on
12 levels
– Precise and reproducible flame
size
– Automatic quick ignition, electronic
flame monitoring with automatic
re-ignition
– Simmer function for cooking on a
very low output level
– Solid smooth-surface cast-iron pan
supports
– Solid stainless steel control knobs
– Precision-crafted 3 mm stainless
steel
– For surface mounting with a visible
edge or for flush mounting
– Can be combined with other Vario
400 series products
Cooking zones
1 multi-ring wok burner (300 W –
5,500 W) 1,000 – 18,800 BTU,
suitable for pots up to max. ø 12 ⅝".
2 two-ring high output burners
(165 W – 4,000 W) 570 – 13,600 BTU,
suitable for pots up to max. ø 11".
2 two-ring standard burners (165 W –
2,000 W) 570 – 6,800 BTU, suitable for
pots up to max. ø 11".
Operation
Control knobs with illuminated
ring, cooking zone and output level
markings.
One-handed operation.
Full electronic control in 12 output
levels for exact power level regulation
plus simmer function.
Automatic quick ignition.
Features
Simmer function.
Three-part cast-iron pan support with
flat, continuous pot surface.
Brass burner rings.
Equipped for natural gas.
For conversion to LP gas, LP kit
(part #10004447) must be ordered.
Safety
Electronic flame monitoring with
automatic re-ignition.
Residual heat indication.
Automatic quick ignition.
Safety shut-off.
Planning notes
Depending on the type of installation
(surface-mounted or flush-mounted),
the specific location of the cut-out and
the knob positions may vary.
The horizontal positioning of the
knobs may be aligned with the specific
burners.
The drawing "Installation of the control
knob" must be observed if the panel is
more than 1" thick (there must be a
recess at the rear).
If combining several Vario 400 series
appliances, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
The weight bearing capacity and stabil-
ity, in the case of thin countertops in
particular, must be supported using
suitable substructures. Take into
account the appliance weight and
additional loads.
Additional instructions for flush mounting:
Installation is possible in countertops
made of stone, synthetics or solid wood.
Heat resistant and watertight sealing of
the cut edges must be observed.
For a suitable heat resistant filler please
consult the countertop manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the countertop cut-out.
If installing several appliances in
individual cut-outs allow for a minimum
distance of 2" between the cooktops.
Plan for an electrical connection
(the appliance is not operable without
power supply).
Air intake from above.
No intermediate shelf required.
Rear panel and wall trims must be
heat-resistant and consist of a
non-flammable material.
A minimum lateral clearance of at least
12" from adjacent heat-sensitive
cabinets or contact surfaces must be
observed or thermal insulation fitted.
Installation in a 36" wide base cabinet
is required.
The combination with VL 414 is not
recommended, since the air extraction
from the center burner cannot be
guaranteed due to the distance.
With a total connected load of more
than 37,533 BTU local regulations
concerning room ventilation, room size
and combination of extraction or
recirculation hoods must be observed.
Minimum clearance between gas
cooktop(s) with more than 37,533 BTU
and ventilation hood must be 30".
Appliance can be snapped into the
countertop from above.
Appliance weight: approx. 70.5 lbs.
Rating
Rating: 25 W (59,700 BTU)
Minimum fuse protection: 15 A
Electrical: 120 V / 60 Hz
Electrical Connection:
Plan for a 55" long connecting cable
with 3 prong NEMA 5-15 plug.
www.gaggenau.com/us
Revised: June 2021