Application Instructions Camelot® Lifetime Designer Shingles Updated: 12/11 Quality You Can Trust… From North America’s Largest Roofing Manufacturer!™ www.gaf.
Quality You Can Trust… From North America’s Largest Roofing Manufacturer!™ ¡Calidad En La Que Usted Puede Confi ar... Del Fabricante De Techos Más Grande De Norteamérica!™ Une Qualité à Laquelle Vous Pouvez Vous Fier... du Plus Gros Fabricant de Toitures en Amérique du Nord! MC INSTALLATION INSTRUCTIONS · INSTRUCCIONES DE INSTALACIÓN · INSTRUCTIONS D’INSTALLATION GENERAL INSTRUCTIONS t 300' %&$,4 Use minimum 3/8" (10mm) plywood or OSB decking as recommended by APA-The Engineered Wood Assn.
t $&.&/50 1-«45*$0 "4'«-5*$0 Use cemento plástico asfáltico conforme a los Tipos I o II de ASTM D4586. t 3&4*45&/$*" "- 7*&/50 4&--"%0 " ."/0 Estas tejas tienen un sellador térmico especial que firmemente une las tejas entre sí después de la aplicación, cuando quedan expuestas al sol y a temperaturas cálidas. Las tejas instaladas en otoño o invierno pueden no sellar hasta la primavera siguiente.
NAILING INSTRUCTIONS / HAND SEALING INSTRUCCIONES DE CLAVADURA / SELLADO A MANO INSTRUCTIONS DE CLOUAGE / SCELLEMENT À LA MAIN These shingles MUST be nailed a nominal 8-1/2" (216mm) from bottom of shingle, above the cut-outs, as shown. Nails must not be exposed. To hand seal shingles and to insure immediate sealing, apply 2 quarter-sized dabs of shingle tab adhesive on the back of each tab, approximately 1" (25mm) from end and 1" (25mm) up from bottom of each tab corner.
INSTALLING UNDERLAYMENT INSTALANDO LA CAPA BASE INSTALLATION DE LA MEMBRANE DE PROTECTION UNDERLAYMENT: FOR ROOF SLOPES 2:12 TO LESS THAN 4:12 Application of eave flashing: At eaves and where ice dams can be expected, use one layer of GAF Leak Barrier. Eave flashing must not overhang the eave edge by more than 1/4" (6mm) and should extend 24" (610mm) beyond the inside wall line. Where ice dams or debris dams are not expected, install 2 plies of GAF Roof Deck Protection.
UNDERLAYMENT: FOR ROOF SLOPES 4:12 OR MORE Application of eave flashing: At eaves and where ice dams can be expected, use one layer of GAF Leak Barrier. Eave flashing must extend 24" (610mm) beyond the inside wall line. Application of underlayment: Cover deck with one layer of GAF roof deck protection installed without wrinkles. Use only enough nails to hold underlayment in place until covered by shingles.
INSTALLING SHINGLES INSTALACIÓN DE TEJAS INSTALLATION DES BARDEAUX FIRST COURSE Shingle exposure should be 7-1/2" (191mm) PRIMERA HILADA La exposición de la tablilla debe ser 7-1/2" (191mm) PREMIER RANG L’exposition de bardeau devrait être 191mm (7-1/2po) Start at either rake and lay in either direction Comience en cualquier inclinación y coloque en cualquier dirección Débuter à l’une ou l’autre des inclinaisons et étendre dans les deux directions AF eG d ent nes m o y i la ac der iltr F Un de F e GA F
THIRD COURSE TERCERA HILADA TROISIÈME RANG Trim 8-5/8" (219mm) from rake end of first shingle Recorte 8-5/8" (219mm) del borde de inclinación de la primera teja AF Découper à 219mm (8-5/8po) du bout du premier bardeau nt eG d es e ym ion rla iltrac F e A nd e F d eG FU GA rrera ite d Ba re-Fu Pa /8" 8-5 9mm) (21 " /16 ) 4-5 0mm (11 4TH COURSE AND REMAINING Strike a chalk line about every 6 courses to check parallel alignment with eaves. 4TA.
INSTALLING ROOF ACCESSORIES AND DETAILS INSTALACIÓN DE ACCESORIOS Y DETALLES DE TECHO INSTALLATION DES PRODUITS ROOF ACCESSORIES ET DÉTAILS VENTILATION Install GAF ventilation products for optimal shingle life. See General Instructions and the “Through Ventilation” section. Follow the application instructions for the selected ventilation products. VENTILACIÓN Instale productos de ventilación de GAF para una óptima vida útil de la teja.
$)*./&: '-"4)*/( "/% $3*$,&54 Cover deck around chimney and over wood crickets with GAF roof deck protection. DO NOT run GAF roof deck protection up sides of chimney. Install leak barrier over GAF roof deck protection and up sides of chimney at least 5» (127 mm). Install shop fabricated metal cricket flashings (shown) after underlayments are installed. Seal shingles to the metal flanges (see drawing below).
VALLEY CONSTRUCTION – OPEN Use minimum 20" (508mm) wide aluminum, galvanized steel, copper, or other non-corroding, non-staining metals (24 gauge minimum). Long valleys or local building codes may require wider metal. Nail the metal on the edges so the nail heads hold it in place. Do not puncture the metal. Nailing through the metal may cause leaking and buckling due to movement.
IMPORTANT NOTE: Do NOT use a "California Valley" (shingles installed parallel to the valley center line), which can cause leaking. NOTA IMPORTANTE: No use un "Valle de California" (tejas instaladas en forma paralea a la línea central del valle), el cual podría provocar filtraciones. REMARQUE IMPORTANTE: Ne pas utiliser de " Noue California " (bardeaux installès en paralléle avec la ligne de centre de la noue), cela peut causer des fuites. 11.
PRECAUTIONARY NOTES 1. These shingles are fiberglass, self-sealing asphalt shingles. Because of the natural characteristics of the high-quality waterproofing material used, these shingles will be stiff in cold weather and flexible in hot weather. 2. These shingles are particularly tough and may require additional effort to trim to fit on the roof. Curved blade utility knives are more effective than straight blade utility knives in cutting these shingles.
