FPC-85 / FLAT PANEL TV CART for 55 – 85 in.
Thank you for choosing Gabor. The Gabor FPC-85 Flat-Panel TV Cart is the modern heavy duty rolling A/V cart. Wheel your 85-inch monitor, laptop, and webcam from room to room, whether it’s at the office, on the sales floor, or in school. If you have safety concerns about installing this product, contact a qualified professional or installation contractor. If this product is missing hardware or there are defective parts, visit www.madebygabor.com or call Customer Service at 212-594-2353.
Safety Warnings • When installing this product, be sure to refer to the mounting instructions detailed in this manual; failure to follow the mounting instructions may void the product warranty. • It is strongly recommended that this product be installed by a qualified professional or installation contractor; Gabor takes no responsibility for any product damage or personal injury resulting from mishandling, incorrect mounting, faulty assembly, or improper use of this product.
Product Specifications Compatible flat-panel display size: 55 to 85 in. (139.7 to 215.9 cm) 30.9 in. (100 cm) 28.2 in. (71.6 cm) Max height: 66 in. (167.5 cm) Min height: 47.8 in. (121.4 cm) Max weight capacity: 200 lb. (90.7 kg) Weight: 64.6 lb. (29.3 kg) 17.7 in. (44.9 cm) VESA mounting pattern: 200 × 200 to 800 × 500 mm 38.5 in. (100 cm) Material: Steel A/V shelf size: 17.7 × 13.3 in. (44.9 × 33.7 cm) Max A/V shelf load: 25 lb. (11.3 kg) 4 66 in. (167.5 cm) max 47.8 in. (121.
Parts List Required tool: Phillips screwdriver and washer 5
Installing the Casters Step 1 Lock the casters during installation and cart assembly. Turn over Step 2 Setting Up the Risers 1. Lay the riser assembly on a flat surface. 2. Remove the locking screws. 3. Pull the riser out approximately 2 inches, until the spring pin securely pops into the open hole. 4. Repeat these steps for the second riser.
Attaching the Riser Post Step 1 Make sure the cable-management holes are facing the rear of the base.
Adjusting the Riser Height Right riser Left riser Hold onto the riser when adjusting the height. Posts Spring pin Step 1 Spring pin Important! Always insert the locking screw one space above the spring pin.
A/V Shelf Assembly and Installation Step 1 Step 2 Step 4 Step 3 9
Installing the Display Mount 10
Installing the Display/TV Bracket Selecting the Right VESA Mounting Hardware for Your Display A variety of screws are included to fit VESA standards on the back of most displays. Select the appropriate M5, M6, or M8 screws and washers. Hand-thread the screws to determine the correct diameter. E D (A,B,C) If the screw is too short, it may not hold the display. If it’s too long, it may damage the display.
Mounting the TV to the Display Mount Step 1 Step 2 Step 3 12
Camera Tray Attachment Step 1 Step 2 Step 3 Step 4 Step 5 13
Installing Power and A/V Cables Step 1 14 Step 2
TV Height Adjustment Important! Adjusting the TV height is at minimum a two-person job. These steps must be done by at least two people. 1. Lock the casters. 2. Unplug all connected devices. Caution: Make sure the cables have enough slack to move the risers up or down. 3. Hold the TV while your partner removes the security screws and presses the spring pins. 4. Move the risers to the desired height until the spring pins pop into their holes. Then reinsert the security screws.
FIVE-YEAR LIMITED WARRANTY This GABOR product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of five (5) years from the original purchase date or thirty (30) days after replacement, whichever occurs later.