User’s Manual Hi-Diagnosis 1.Power on/off and method of switch operation 2. Installation of trigger module and cigar power cable 3. Scantool-Communication Open and Retry 4. Install configuration and Procedure of Hi-Diagnosis 5.
User’s Manual 1 Power on/off and method of switch operation H/W understanding for Hi-Diagnosis Module : A–01-005 (p.01) 1. VCI Power On To turn on the VCI equipment, first of all, connect DLC cable from vehicle to VCI module and depressing the main switch.
User’s Manual Module : A-01-005 (p.02) [Figure 2. LED status on window of VCI main module] ① POWER LED displays with turn VCI equipment on. Color of this LED reflects which function has been running on VCI equipment either diagnosis or flight record mode. Yellow refers to diagnosis mode and red is for flight record mode. ② VEH. COMM The condition of Vehicle Communication can be confirmed by LEDs.
User’s Manual Module : A-01-005 (p.03) 3. Switch operation of trigger module 1) Switch operation of trigger module (Enter / Cancel) There are buttons for “ENTER” and “CANCEL” on the trigger module. The communication data is stored into memory of VCI by depressing “ENTER” button during the Flight Record mode. And the “ENTER” button can be undone by depressing the “CANCEL” button. 2) Lamp of trigger module (Power / Ready) Trigger module has two different LEDs.
User’s Manual Installation of trigger module and cigar power cable H/W understanding for Hi-Diagnosis Module : A–01-004 (p.01) Trigger module of VCI equipment has two purposes. This trigger module sends the trigger signal to VCI main module when trouble occurrence. And trigger signal is sent to VCI by depressing the trigger button with Flight Record mode. According to this trigger signal, the VCI module starts to store the Flight Record Data. The VCI module receives ON/OFF signal from trigger module.
User’s Manual Module : A-01-004 (p.02) [Figure 2. Connection of cigar jack] [Figure 3.
User’s Manual Scantool-Communication Open and Retry Hi-Diagnosis program-DIAGNOSIS Module : A –04 –006 (p.01) 1. Vehicle and Control Module Selection If “ScanTool” menu item is selected before the vehicle/system selection through VIN selection, vehicle/system selection window appears as shown in [Figure 1]. Accurate system is necessary for the communication. In Hi-Diagnosis, there is no need to go through additional vehicle selection after the first selection for the use of other functions.
User’s Manual Module : A-04-006 (p.02) 1) VIN Selection There are three ways to select vehicle. ① By Inputting Vehicle Identification Number consists of 17 figure codes combined by letters and numbers. ② By selecting vehicle, model year, and engine ③ By using VIN Auto Detect function (1) Input of VIN with 17-figure codes combined with number and Letter There is a way to input all 17-figure code of VIN in the VIN input box. Another way is to input part of the 17-figure code and choose from the list.
User’s Manual Module : A-04-006 (p.03) [Figure 3. VIN Input – Part of 17 figures] (2) Method to select Vehicle, Model Year and Engine Select “Vehicle”, “Model year”, and “Engine” in each section for a vehicle, and control modules that can be applied will appear on the window. [Figure 4.
User’s Manual Module : A-04-006 (p.04) 2) Control module selection for scantool and fault code searching (1) Selection of control module for scantool By selecting “Vehicle”, “Model Year”, and “Engine” in the “Vehicle Selection”, VCI module for vehicle communication is selected in the “Selected section” in default, for using “Scantool” function. Default setting for “Selected” section is always in “Engine”, and user can change to other control modules.
User’s Manual Module : A-04-006 (p.05) (2) Selection of control module for fault code searching “Fault Code Searching” function finds DTC automatically for selected control module through the communication between a VCI and a vehicle. If DTC is found, “By DTC” function on the “Hot Fix” menu can be effective. ① Control module selection Click “Fault Code Searching Turn Off” button in order to change to “Turn On” State, for a use of “Fault Code Searching” function.
User’s Manual Module : A-04-006 (p.06) [Figure 8. Control module change] ③ Change of control module for scantool function Among the control modules in the “Selected” section, it is possible to assign a control module as a default setting for the communication during the use of “ScanTool” function. The Icon with the “V” sign on the top, is a default module that will be used for communication. Change in the default communication module is made through the mouse selection of other control modules.
User’s Manual Module : A-04-006 (p.07) (3) Process and result for fault code searching function By Setting and running “ Fault Code Searching” function in the “ Vehicle Selection” can automatically diagnose DTC during the use of other Hi-Diagnosis functions through the communication between a VCI and a vehicle. The progress rate for the Fault Code Searching will be displayed on the top of the “Fault Code Searching” icon, which is located on the lower section of the Hi-Diagnosis screen.
User’s Manual Module : A-04-006 (p.08) 3) Trouble symptoms selection Select and input vehicle symptom in the “Symptoms in this vehicle” section on the “Vehicle Selection” window. Selection Menu on the left can be categorized into groups of “Engine”, “Transmission”, and “Brake”. The right menu is for the selection of symptom for the selected group on the left. The symptoms are “Hard/No starts”, “Idle-irregularity”, “Engine Stall” and etc.
User’s Manual Module : A-04-006 (p.09) 2. Communication Open If the system selection is completed, the stage to open a communication with the control module to be diagnosed is necessary for the communication. Check following matters before opening the communication. 1) Ignition switch of a vehicle should be turned on. 2) DLC cable of VCI should be correctly connected to the DLC connector of the vehicle. 3) VCI module power should be turned on. 4) Connection between the PC and VCI should be stable.
User’s Manual Module : A-04-006 (p.10) 3. Communication Result After the “Communication Open” communication stays connected if user does not turn off the VCI nor switches the ignition switch to less than On. If there is a disturbance between the communication, connection may be lost. [Figure 13.
User’s Manual Module : A-04-006 (p.11) 4. Communication Retry If the communication is lost between the PC and the VCI or the VCI and the Vehicle, it is possible to retry connection by going back to the initial page and clicking the “Retry” button. “Retry” button is located in the upper right section of the screen, and retries to make connection for the selected system control module when it is pressed. Following matters should be checked before the communication.
User’s Manual Module : A-04-006 (p.12) 5. Control Module Changing If user wants to connect in different control module in same vehicle at the current page, reselect the control module to communicate with system reselect button. [Figure 15.
User’s Manual Install configuration and Procedure of Hi-Diagnosis S/W Understanding for Hi-Diagnosis Module : A–02-001 (p.01) 1. Meeting Hardware Requirements 1) Minimum System Requirements (1) PC Operation System: above Windows 2000 (IIS (Internet Information Server) eligible OS) (2) CPU: 500MHz Intel Pentium III Processor or higher microprocessor (or equivalent) (3) RAM capacity: 256 megabyte (MB) of RAM is recommended minimum. (4) Hard Disk Capacity: 20GB Hard disk with minimum 5GB of free space.
User’s Manual Module : A-02-001 (p.02) (9) Wireless LAN: Intel. PRO/Wireless 2200BG network connection 802.11b+g (10) Touch screen PC: Microsoft. Windows.
User’s Manual 2. Install Process for Hi-Diagnosis Software Module : A-02-001 (p.
User’s Manual Specifications and features H/W understanding for Hi-Diagnosis Module : A–01-002 (p.01) 1. Specifications of VCI 1) General features Item Specifications 1. 2. Micro Controller Memory 3. Operating Voltage 4. Operating Temperature 14 ℉~158 ℉ (-10℃ ~ 70℃) : USB Mode Diagnosis Function / Flight Record Function Typical 350mA @12V 7. Operating Mode Current Consumption Housing 8. 9. Dimension Weigh 5. 6.
User’s Manual Module : A-01-002 (p.02) 4) Added Interface Item 1. VSS 2.
User’s Manual Module : A-01-002 (p.03) 2. Specification of Information Terminal 1) Functional Features Item Specifications 1. CPU 2. Memory Ultra Low Voltage Centrino Pentium M 900MHz 512MB SDRAM (DDR) standard, expandable to 768MB 3. Storage 4. Display 60GB HDD 10.4" 1024 x 768 XGA transreflective, anti-reflective TFT Active Matrix Colour LCD 5. Keyboard 82-key with dedicated Windows key 6. Pointing Device Pressure Sensing touchpad with vertical scrolling support 7.
User’s Manual Module : A-01-002 (p.04) 2) Implemental Features Item 1. Dimension Specifications Height Width 48.26mm 271.7mm Depth 215.9mm 2.0kg(4.4lb) Full Magnesium Alloy Case; Moisture and dust resistant LCD; Keyboard and touchpad; Sealed port and connector covers; Shock-mounted HDD; Rugged hinge 2. Weight 3. Structure Remark 3) Electrical Features Item Specifications 1. AC Input AC 100V-240V 50/60Hz, Auto Sensing/Switching world-wide power supply 2. Battery Lithium Ion battery pack(7.
FCC NOTICE THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITION: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED OPERATION. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
