Specifications
Turning on
• Press and hold for 3 sec.
Pairing G-Grip
• Activate Bluetooth® on your device.
• Turn on device by pressing the shutter button until the
status light is ashing green.
• Add Bluetooth® device in phone settings.
• Select ‘GGrip’ from the list of available devices.
Shooting photos
• Select Photo mode on your device.
• Press shutter once for single picture.
• For Burst mode, press and hold (for up to 3 minutes).
Note: To congure Burst mode on iPhone, go to
Settings > Camera and enable the option to ‘Use Volume
Up for Burst’.
Shooting videos
• Select Video mode on your device.
• Press shutter once to record, and again to stop.
Turning o
• The device will go into automatic standby mode after
6 minutes of inactivity.
Charging G-Grip
• The status LED will show red when the battery is low,
charge your G-Grip using a USB-C charger (charger and
cable not supplied) until the red light has turned o.
Troubleshooting – lost connection
• If the status LED on the G-Grip ashes green, this means
it has been disconnected from your device.
• Ensure Bluetooth® is turned on in settings on your device.
• Turn on device by pressing the shutter button until the
status light is ashing green.
• Add Bluetooth® device in phone settings.
• Select ‘GGrip’ from the list of available devices.
• Transition frequency 2.4000GHz - 2.4835GHz.
• Communication distance 10m (30ft).
• Battery life 20 hours in use and 4,000 hours on standby.
Compatible devices
• iPhone with iOS 6 and above.
• Android OS 4.2 and above.
• Compatible devices require Bluetooth® 4.0+ support and
use of side volume key as the shutter button.
Legal
G-Grip does not accept any liability for loss or damage
to devices or objects as a result of the G-Grip being
incorrectly attached to a device.
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. Other
trademarks and trade names are those of their
respective owners.
Regulatory Conformance
Radio equipment conformity statement (see opposite).
The user is cautioned that changes or modications
not expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment. This device complies with Part 15 of
the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation. NOTE: This equipment has
been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorientate or relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Recycling
Please recycle all materials used in packaging.
Designed and developed in the UK. Made in China.
Patent pending.
The product is a portable device and meets the
exposure assessment requirements for portable
devices.
Using G-Grip Specications Caution