Installation Instructions

ManualsBrandsFUZHOU SUNNY ELECTRONIC ManualsElectronicsWireless Indoor Outdoor Thermometer and Clock with Remote Sensor

Wireless Indoor/Outdoor Thermometer & Clock with Remote Sensor

Model 1730

Simple, reliable, accurate…the wireless thermometer & clock allows you to monitor indoor or

outdoor locations from one room. The base station reads indoor conditions, while the remote

sensor wirelessly reports outdoor weather conditions back to the base station for an all-in-one

weather display.

NOTE: Some stations have a static cling label over the digital display. Please remove it before use.

BATTERY INFORMATION

IMPORTANT: Install batteries in the base station first, then the remote sensor, otherwise the

stations’ transmissions may not properly connect. Place the base station as close as possible to

the remote sensor when installing batteries.

Base Station:

The base station operates on 2 AAA batteries (not included). The battery compartment is located

on the back of the station. Remove the battery compartment door. Install (2) AAA size batteries

into the battery compartment according to the polarity markings. Replace the battery

compartment door.

Remote Sensor:

The remote sensor operates on 2 AAA batteries (not included). The battery compartment is

located on the back of the station. Slide off the battery compartment cover. Install (2) AAA size

batteries into the battery compartment according to the polarity markings. Replace the battery

compartment door.

After Batteries are Installed:

When the stations are powered up, the LCD screen on the base station will light up for 3 seconds,

then the station will display initial indoor temperature readings. The outdoor temperature

display will show dashes “(--)”.

Press and hold the button on the front of the base station to activate the paring to obtain

outdoor temperature. A transmission signal icon (“ ”) flashes by the “OUT” temperature digits

during this time. When the “ ” icon turns off, the base station has connected with the remote

and starts reporting the current outdoor temperature.

Summary of content (7 pages)

PAGE 1
Wireless Indoor/Outdoor Thermometer & Clock with Remote Sensor Model 1730 Simple, reliable, accurate…the wireless thermometer & clock allows you to monitor indoor or outdoor locations from one room. The base station reads indoor conditions, while the remote sensor wirelessly reports outdoor weather conditions back to the base station for an all-in-one weather display. NOTE: Some stations have a static cling label over the digital display. Please remove it before use.
PAGE 2
For best setup connection, keep the base station and remote close to each other while trying to connect. Keep away from other electronic equipment that may interfere with the connections, such as mobile phones, appliances, computers, refrigerators, TVs, etc. Indoor temperature readings update on the base station approximately every 30 seconds. The remote sensor transmits outdoor temperature readings to the base station approximately every 57 seconds.
PAGE 3
The transmission range of the remote sensor is 200 feet. The effective transmission range is vastly affected by obstacles such as walls, sheds, trees, etc. Try various setups for the best results. Shorten the distance between the base and remote stations when necessary. To get the most accurate readings and to prolong the life of your sensor, we recommend that you mount it out of direct sunlight and rain. Direct sunlight will heat the casing and inflate temperature readings.
PAGE 4
Until a time has been set, the clock will count up the time since battery installation. MAXIMUM/MINIMUM TEMPERATURE MEMORY RECALL The thermometer will store the last recorded high and low temperatures over a 24-hour period. The 24-hour period starts when the stations are powered up. ● Press the “MEM” button on the back of the base station once to display the maximum indoor and outdoor temperature readings since the station was last reset. “MAX” will show on the LCD.
PAGE 5
outside that range. Therefore, 2 stations placed next to each other may report different readings. This is a normal occurrence with digital sensors and should not be considered a defect. 4. For maximum performance in normal conditions, good quality alkaline batteries are recommended. When temperatures are below 0°F, alkaline batteries can lose power resulting in a loss of remote transmission.
PAGE 6
Outdoor temperature range transmitted by remote sensor: Alkaline batteries: -4°F to 140°F (-20°C to 60°C) Lithium batteries: -40°F to 140°F (-40°C to 60°C) Resolution: 0.1 degree for temperature Indoor temperature readings update approximately every 30 seconds Remote sensor transmits temperature readings every 57 seconds.
PAGE 7
-Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Warning: Federal Communications Commission (FCC) Statement. This device complies with part 15 of the FCC Rules.