E3PDA User Manual Ver：V1.
Contents 1 Introduction............................................................................................................ 1 1.1 1.2 1.3 1.4 1.5 1.6 Appearance of E3PDA............................................................................................................... 1 Installing an SD Card..................................................................................................................2 Installing a SIM Card..............................................................
E3PDA User Manual 1 Introduction 1.
E3PDA User Manual 1.2 Installing an SD Card To install an SD card, do as follows: 1. Push the card cover along the direction marked on the cover and open the cover. 2. Insert an SD card. 3. Press the SD card downward and lock the card along the IN direction marked on the cover.
E3PDA User Manual 1.3 Installing a SIM Card To install a SIM card, do as follows: 1. Insert a SIM card along the direction, as shown in Figure 1-4. 2. Press the card cover downward. 3. Push the SIM card along the LOCK direction to lock the card cover. Figure 1-4 Inserting a SIM card 1.4 Installing a Battery To install a battery, do as follows: 1. Push the battery to the bottom of the battery compartment. 2. Press the top of the battery downward to tighten the battery. 3.
E3PDA User Manual Figure 1-5 Installing a battery 1.5 Disassembling the Battery Cover To disassemble the battery cover, do as follows: 1. Insert your left forefinger into the upper left part of the battery cover and push the lock to the left by using the thumb. 2. Pull out the battery cover.
E3PDA User Manual Figure 1-6 Disassembling the battery cover 1.6 Charging You can charge the E3PDA in the following ways: 1. Charge the E3PDA by using bottom charging cable. 2. Connect the E3PDA to a PC by using a USB cable to charge the E3PDA. In the charging status, the LED is red. When the LED becomes blue, charging is complete. When the battery volume is insufficient, the E3PDA displays alarm information. When the battery volume is too low, the E3PDA is automatically powered off.
E3PDA User Manual 2 Instructions on the E3PDA 2.1 Power-on and Power-off After installing a SIM card and a battery and fully charging the E3PDA, you can use the E3PDA. 1. To power on the E3PDA, press and hold the On/Off key for some time. The power-on page is displayed. After the guiding progress is complete, the E3PDAenters the Android system. It takes some time to initialize the E3PDA. Please wait patiently. 2. To power off the E3PDA, press and hold the On/Off key for some time.
E3PDA User Manual Scan key: Used to scan data. Return key: Used to return to the previous operation page. Menu key: Used to display a menu. Home key Menu key Return key 2.4 Home The E3PDA has five home pages. Slide to the left or right to switch among the pages. Click any application on the home page to start the application. Application tray ★ Tips You can add application icons in blank space of the home page. Click the application tray to view all applications. 2.
E3PDA User Manual Table 2-1 Status icons Icon Description Icon Description WLAN Signal strength EDGE Offline mode USB connection Internet access restricted Missed calls USB debug New messages Charging Modem logs Full power Mute mode There are multiple notification icons, which are beyond the scope of display. Connect to Pea ★ Note The applications of the E3PDA are often upgraded. Therefore, the status icons may be different from those on the E3PDA. The actual status icons prevail. 2.
E3PDA User Manual 2.6.2 Display Settings Find the following icon: Select Settings > Display and set display options such as Brightness, Wallpaper, Autorotate screen, and Font size. 2.6.3 Ringtone Setting Select Settings > Audio Profiles and click General/Silent/Meeting/Outdoor to set the ringtone in the corresponding mode.
E3PDA User Manual 2.6.4 Security Setting Select Settings > Reset > Factory date reset. Click Clear all. The E3PDA starts to restore the factory settings.
E3PDA User Manual Current system software and bound applications Files in the SD card, for example, music and pictures 2.6.5 Language and Input Setting Select Settings > Language and input. In the displayed list, select the desired language. Click Default and select the desired input in the list. 2.6.6 Shortcuts You can add shortcut icons on the home page of the E3PDA. On the home page, click the application tray icon, select and drag the icon to be added to the home page. 2.6.
E3PDA User Manual 3 Call Function 3.1 Making a Call Find the following icon: 1. Enter a telephone number by pressing number keys. . 2. Click 3. Click to terminate the call. Contact Call record Voice call Virtual numeric keypad 3.2 Contacts Find the following icon: 1. Click Contacts to open the contact list. 2. To add a contact, click . 3. To import or export contacts, press the menu key to open the menu and click Import/export. 4.
E3PDA User Manual 3.3 SMS and MMS Find the following icon: 1. Click and enter the message recipient and the text to be sent. 2. Click to send the message. 3. On the message editing page, press the menu key to open the menu and click Add Subject. Convert the message to be sent into a multimedia message and click . ★ Tips Click to add attachments such as picture, video, and audio files.
E3PDA User Manual 3.4 Email You can send or receive emails. ★ Note To create an email account on the E3PDA, you need to set the account on a PC. For example, to create a QQ email account, log in to the QQ mailbox, click Settings in the upper right corner of the mailbox to access the account options. Find the server options and email receiving options, select all, and click Save. To set a mailbox on the E3PDA, do as follows: Find the following icon: 1. Enter the email address and password and click Next.
E3PDA User Manual To delete an account, do as follows: 1. On the mailbox page, press the menu key and click Settings. 2. Click the email account to be deleted and access the setting page. 3. Click Remove account.
E3PDA User Manual 4. Network and Connection Synchronization 4.1 Data Connection By default, the network is configured for the device upon delivery. If you delete the network configuration by mistake, you can manually select a network through software configuration. In hardware, different antennas are used in two network modes. In software, you need to perform the following configuration: Select Settings > More > Mobile Networks > Network Mode and manually select the CDMA or GSM network.
E3PDA User Manual After a GPRS data connection is established, you can access the Internet. To establish a GPRS data connection, ensure that a SIM card is installed in the E3PDA. Generally, the E3PDA has configured Internet access.
E3PDA User Manual 4.2 Wi-Fi Network Connection Select Settings > Wireless & networks > WLAN. 1. Click On for Wi-Fi. The system starts to search for the network. If the WLAN is enabled, click Scan. The E3PDA list the searched networks. 2. Click the network to be connected and enter the password in the displayed dialogbox. 3. Click Connect to complete the Wi-Fi connection. Click to enable Wi-Fi and search for networks 点按连接至网络 Click to connect to the network 4.
E3PDA User Manual 4.4 Connecting E3PDA to a Computer Connect the E3PDA to a computer by using a USB cable so that files in the memory card, for example, pictures, videos, and music, can be transferred to the computer and processed in the computer. 1. Connect the E3PDA to a USB port of a computer by using the USB cable. 2. The icon of USB connection is displayed in the status bar of the E3PDA. Slide the status bar, you can see USB connected and select the USB connection mode.
E3PDA User Manual 4.5 Synchronization Select Settings > Accounts & sync. 1. Click ADD ACCOUNT to set a new account. 2. Click Company or Email, enter the email address and password, and click Next. Wait until the connection is completed (for details about mailbox settings, see section 3.4 Email). 3. Click Accounts & sync. On the Accounts & sync settings page, set the account as required. Set email synchronization frequency, notification, etc. Select the option to synchronize emails.
E3PDA User Manual 5. Introduction to iScan of the E3PDA 5.1 Installing and Using iScan To collect data, you must install and start the scan application on the E3PDA. At present, Wuxi iData Technology Company Ltd. provides the scan demonstration software, iScan, for example to obtain and decode barcode information. First of all, install iScan on the E3PDA (for details on how to install iScan, see 6.1 Installing Software). After iScan is installed, the iScan icon is displayed on the application page.
E3PDA User Manual 6 Managing E3PDA 6.1 Installing Software The E3PDA uses Google’s Android platform whose suffix is apk. To install software on the E3PDA, use the following methods: 1. Download and install software through the online software store provided by Google (Google Play) or Android software download platform (HiMarket) used in China. HiMarket is recommended. 2. Download software installation packages, store them on the SD card, and install the software by using file manager. 3.
E3PDA User Manual 6.3 Managing Applications Press the menu key (yellow scan key) and click Manage apps. You can view the status of download applications, applications in the SD card, and running applications and click any application to access the application information page where you can stop, uninstall, or suspend the application.
E3PDA User Manual 7 Precautions and Troubleshooting 7.1 Precautions for E3PDA To ensure that the E3PDA does not fail, follow the following precautions during use of the E3PDA: Put the E3PDA and its components and accessories in the places where children cannot reach. Keep the E3PDA dry. Rain, moisture and liquid contain acidic materials and will corrode the circuit board. Do not store or use the E3PDA in dusty or dirty places. Do not store the E3PDA in a place that is too hot.
E3PDA User Manual Do not put the battery into a fire. If the battery leaks, do not let the liquid stain your skin or eyes. Otherwise, wash your skin or eyes with lots of water and go to see the doctor immediately. Cleaning the E3PDA Shell Clean the shell by using a cloth soaked with alcohol, including keys and space between keys. Display You can clean the display screen by using a cloth soaked with alcohol. Do not let the liquid gather around the screen.
E3PDA User Manual Fault Cause Solution at a low speed. the E3PDA. necessary, save the records on the host or increase the storage capacity by using an SD card. Too many applications are installed on the E3PDA. Remove applications installed on the iData 95. The scan application is not loaded. Load iScan in the E3PDA. Reading a barcode fails. Check that the barcode is defective. The battery volume is low.
E3PDA User Manual Table 7-2 Cable troubleshooting Fault Cause Solution Charging fails. The cable contact. is in poor Replace the cable. The synchronization software cannot be connected. The cable contact. is in poor Replace the cable. Table 7-3 Wi-Fi connection troubleshooting Fault An AP cannot connected. Cause be “Authentication displayed. Solution fails” is - 27 - The password of the WLAN device is incorrect.
FCC Warning 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.
