User Manual Photo Frame Wi-Fi Security Camera
YOU NEED TO KNOW BEFORE SETUP: 1. Make sure you are using 2.4GHz wireless network, not 5GHz 2. Make sure the RED LED light is blinking slowly when power on. if not, please reset the camera. 3. Make sure your camera and wifi router are not far away. 4. Make sure your phone is close to the camera when configuring. 5. Go to Wi-Fi setting of your smartphone to see if camera ID like YIEYE-XXXXX-XXXXX is matched with the one we put the sticker on the device 6.
1.Product Structure Infrared LED Light Light Dependent Resistor PIR Sensor Camera On Off Charging Port Indicator Power On/Off Button Reset Button Micro SD Slot 2.
3.
4.Specification Camera Built-in image sensor Sensor sensitivity Focal Length Angle of View 1/3" progressive CMOS sensor 1.0 Lux 0.6 mm 60° Algorithm File Format Video recording mode Recording capability Frame rate Night vision PIR detect distance PIR boots up Video file length H.
Recording time Push alarm notification Photo Dimension Product Dimension Weight 400 days@1280*720p (8GB micro SD card not included),base on 10 detecting files per day Motion detected alarm,Low battery 18.2*13.2cm(7.1x5.1INCH) 25.5*19.8*1.7cm(10x7.8x0.66INCH) 0.4KG(0.8LB) App name Mobile surveillance Remote access Bracket Indoor/outdoor usage Yieye iPhone, Android Yes Manual adjustable Indoor Others 5.Charging the battery This unit has a built-in rechargeable lithium battery.
6.Format Memory Card There are two ways to format the memory card. 1).Format the card on computer. 2).Insert micro SD card into memory card slot. Go to Yi eye app to format. More information ,please refer to 9.5 Playback&Share Videos and Photos in user manual. 7.LED Light State Introduction No.
9.Start using the device Wi-Fi Configuration Step 1 Place the photo frame camera on a flat surface close to home router along with user’s mobile phone, slide the ON/OFF switch to On position. Red LED blinks within 180 seconds. On Off Note:lt only support 2.4Ghz internet Wi-Fi network,no 5G network.
AT&T Settings 11:50 AM Step 2 Wait a full 40 seconds for the device to boot up, then enter Setting on the phone, select Wi-Fi, scan and join the network of Wi-Fi router. Wi-Fi Wi-Fi FYX_6211_2.4G i Note: A.Please do not directly connect and join camera ID in Wi-Fi setting of your smartphone B.If there is no camera ID like YIEYE-XXXXXXXXXXX displayed, please insert reset pin to press and hold Reset button up to 10 seconds and then release to reset the camera. CHOOSE A NETWORK...
AT&T 11:50 AM 三 Yi Eye AT&T + Back Step 3 Open the Yi eye APP on the phone,and click Tap to add a device. AT&T Back 11:50 AM Select device type Step 4 Tap on Photo Frame Camera as shown. 11:50 AM Camera Configuration Confirm whether red LED is blinking On Off Red LED is not blinking Red LED is Blinking Slowly Add online devices Step 5 Tap on Red LED is blinking slowly.
AT&T 11:50 AM Step 6 Select method A,B,or C to add device. A B QR Scan C A:Scan the QR code on your device,this is the quickest way to add the camera. Yi Eye YIEYE-002335-SXDSP B:Press the icon phone’s photos.
C. AT&T 11:50 AM Mannual input UID Back UID YIEYE-002355-SXDSR X OK Press the pencil icon on the lower right corner, and enter camera ID on your device as shown. AT&T Back 11:50 AM lnternet Wi-Fi configuration Enter Wi-Fi password 1 Wi-Fi SSID FYX_6211_2.4G Wi-Fi password 2 *********** Display password *Not support 5Ghz Wi-Fi 3 Proceed Step 7 Enter the home owner’s SSID and password, then press Proceed. Notice: It do not support 5Ghz wireless network, Only 2.
AT&T Back 11:50 AM Enter Access Password 1 2 Step 8 Enter owner’s access password and keep in mind in case,then tap on Smart Config. Smart Config 3 Step 9 1.Press "Send Sound Wave" button and wait for the device indicator to turn solid green. then click Next button.
AT&T Back 11:50 AM lnternet Wi-Fi configuration 2.Waiting for camera to be connected with 2.4Ghz wireless router. If fail to connect, please try it again! Note: A. Please put your smart phone to the device within 10CM. B.Turn the volume of smart-phone to maximum. C.If configuration failed: Please make sure enter correct Wi-Fi password (Note: case-sensitive and blank). Keep the environment is quiet when do the configuration.
9.1 Watch Live Video AT&T More settings Camera name Camera ID 11:50 AM Add a camera Yi Eye 123 2018.7.25 14:24:01 Date/Time display YIEYE-002335-SXDSR Online status online Delete a camera Enable/Disable disturb mode Camera settings Play SD videos Motion detection setting AT&T 11:50 AM 1.Motion notification center 2.Videos/photos recorded in APP 3.
AT&T Camera name FPS 11:50 AM Enable full screen Battery status 123 1272kbps 15fps Real-time Wi-Fi signal 2018.7.25 14:24:01 Press to speak (Not available) Date/Time Press to listen Take snapshot (Saved in ablum of APP) Press to record video (Saved in album of APP) 9.2 Add Online Devices AT&T 三 11:50 AM Yi Eye + Step 1 Open the Yi eye APP on the phone,and click icon on the top right corner.
AT&T Back AT&T 11:50 AM Select device type Back 11:50 AM Camera Configuration Confirm whether red LED is blinking Red LED is not blinking Red LED is Blinking Slowly Add online devices Step 2 Tap on Photo Frame Camera as shown. AT&T 11:50 AM A B Step 3 Tap on Add online devices. QR Scan C Step 4 Select method A,B,or C to add online device, more information,please follow Step 6 above.
AT&T Back AT&T 11:50 AM Enter password Back 11:50 AM lnternet Wi-Fi configuration New password * X Save Step 5 Enter correct camera’s password, select Save. AT&T Back Step 6 Wait few seconds as shown. 11:50 AM Camera lnfo Living Room Backyard Camera Alias 123 X Save Step 7 Name the device ,tap on Save .The device will be online.
9.3 Motion Detection Setting AT&T 1 2 AT&T 11:50 AM Motion detection 11:50 AM Motion detection Save 3 4 Enable motion record 1.Slide Enable to On position 2.Tap on More setting 3.Select Sensitivity(Low/Medium/High) 4.Select video file length of motion record(10-60 seconds selectable, 10 seconds defaulted) 5.
AT&T 11:50 AM Motion detection AT&T 11:50 AM Motion detection Save 1 4 Save 3 2 AT&T 6 5 Enable schedule motion record 1.Slide Enable to On position 2.Select Detection schedule setting 3.Select All with check mark icon to setup full time motion alarm 4.Tap Days icon to select which day to setup alarm (Through Monday to Sunday, multiple selection available) 5.Select time period for schedule record 6.
AT&T 11:50 AM Motion detection Save Disable schedule motion record 1.Unmark All with the check icon 2.Press Save on the upper right corner and back to live view mode 9.
AT&T 11:50 AM Motion detection AT&T 11:50 AM Yi Eye Save 123 2018.7.25 14:24:01 YIEYE-002335-SXDSR online Step 3 Disable disturb mode. Step 2 Enable motion detection as shown. AT&T Step 4 The phone will receive notification message as shown once motion is detected.
9.5 Playback&Share Videos and Photos AT&T 11:50 AM Yi Eye 2018.7.25 14:24:01 123 YIEYE-002335-SXDSR Enter into SD card playback menu as shown. online AT&T Back 11:50 AM Remote playback i 1 2 3 1.Choose date 2.Tap to play video 3.Share video to friends and family members as shown.
Memory Card information AT&T Back 3 11:50 AM Remote playback i 1 1. Memory card info menu 2. Enable/disable loop recording 3. SD card information 4.
3 4 AT&T 11:50 AM Photos Back AT&T Edit 11:50 AM Back 2018.7.25 14:24:01 2018-08-17 17:00:48.jpg 2018-08-17 17:00:48.jpg YIEYE-002335-SXDSR_2018-08-01 17:00:50.jpg Share your favorite picture to friends and family members as shown.
3 AT&T 11:50 AM Videos Back Edit Share your favorite video to friends and family members as shown. 9.6 Change Device Code AT&T Back 11:50 AM Change password Go to Settings in APP ,and tap on Access code, then enter the information asked(Old/New code/ Re-enter new code),and press Save.
9.7 Reset Photo frame WiFi Camera can be reset in the following ways: 1).Using reset pin ,press and hold the reset the button for 10 seconds to reset WiFi video camera and restore the factory settings after power on device. 2).Go to Settings in APP,and tap on Restore to factory setting ,then click as shown.
9.8 Change the IP connection from A internet to B internet Default the device as point 9.7,then follow point 9 to configure internet Wi-Fi. 9.9 Other Options AT&T 1 2 Back 11:50 AM settings 3 4 5 6 7 1.Change camera name as your demand and update the latest firmware to the camera when available. 2.Setup correct time and date stamping 3.Change the image display direction. 4.Enter correct power frequence 5.Adjust speaker and microphone volume(Speaker not available,audio disabled) 6.
Emai: care@fuvision.