3. SETTING AND ADJUSTMENT 3.4 How to Enable and Disable Alerts You can enable or disable alerts from the [ALERT ENABLE] menu. Disabling an alert in this menu will disable all related alerts for the disabled alert. Note: All alerts are set to [ENABLE] by default. 1. Access the [INITIAL SET] menu, following the procedure outlined in "How to access the [INITIAL SET] menu" on page 3-1. 2. Select [ALERT ENABLE], then press the ENT/ACK key.
3. SETTING AND ADJUSTMENT 3.5 How to Set Up the I/O Ports 1. Access the [INITIAL SET] menu, following the procedure outlined in "How to access the [INITIAL SET] menu" on page 3-1. 2. Select [I/O PORT], then press the ENT/ACK key.
. SETTING AND ADJUSTMENT 3.5.1 How to set port priority 1. Access the [INITIAL SET] menu, following the procedure outlined in "How to access the [INITIAL SET] menu" on page 3-1. 2. Select [PORT PRIORITY], then press the ENT/ACK key. Selected item is highlighted in reverse video. PORT PRIORITY PRIORITY 1st 2nd 3rd 4th 5th 6th LL/COG/COG SENSOR1 SENSOR2 SENSOR3 COM4 COM5 COM6 : CURSOR ENT HDG SENSOR3 SENSOR1 SENSOR2 COM6 COM4 COM5 : SELECT ROT SENSOR3 SENSOR1 SENSOR2 COM6 COM4 COM5 ENT : BACK 3.
3. SETTING AND ADJUSTMENT 10. Select [ON] to enable AIS data output to the NAVNET network when this unit is turned on. Select [OFF] to disable AIS data output when this unit is turned on. 11. Set [ZDA INFO] and [GPS INFO] in the same manner as [AIS INFO], then go to step 14. 12. Select [SFI], then press the ENT/ACK key. 13. Set the [SFI] (System Function ID), then press the ENT/ACK key. 14. Confirm the settings are correct, then select [] and press the ENT/ACK key. A confirmation pop up is displayed.
3. SETTING AND ADJUSTMENT 3.7.3 How to set the network protocol Set the LAN network protocol according to your vessel’s on-board network. [NAVNET] protocol should be used where a NavNet series unit is the LAN network hub. Select [450] for all other LAN networks. 1. Access the [SERVICE] menu referring to the procedure outlined at the start of this section. 2. Select [OTHER SET], then press the ENT/ACK key. 3. Select [NW PROTOCOL], then press the ENT/ACK key.
APPENDIX 1 JIS CABLE GUIDE Cables listed in the manual are usually shown as Japanese Industrial Standard (JIS). Use the following guide to locate an equivalent cable locally. JIS cable names may have up to 6 alphabetical characters, followed by a dash and a numerical value (example: DPYC-2.5). For core types D and T, the numerical designation indicates the cross-sectional Area (mm2) of the core wire(s) in the cable.
APPENDIX 2 DIGITAL INTERFACE IEC61162-1/2 data sentences IEC61162-1/2 format data is input or output from the data port COM1-COM6. The table below shows the input/output data specifications for the transponder unit (FA-1701).
APPENDIX 2 DIGITAL INTERFACE Transmission intervals Sentence ABK Interval With each event Sentence ACA ACS ALF ALC ALR ARC Transmitted after ACA When requested, or with each event With each event HBT LR2 LRF NAK 50 seconds With each event With each event With each event LR1 LR3 LRI PIWWIVD PIWWSPR When requested, or with each event When requested, or with each event When requested, or with each event With each event When requested, or with each event, or powered on PIWWSSD PIWWVSD TRL VDM VER
APPENDIX 2 DIGITAL INTERFACE Serial & contact interface I/O circuit COM1, 2 ADM2587E 120Ω COM1_RD_TERM COM1_RD_B COM1_RD_A RD COM1_TD_B COM1_TD_A TD GND1-4 GND5-8 GND COM1_GND_ISO COM3 to COM6 ADM2587E 120Ω RD COM3_RD_B COM3_RD_A TD COM3_TD_B COM3_TD_A GND1-4 GND5-8 GND COM3_GND_ISO External P3.3V TLP4176 EXT_ALM_NC_H EXT_ALM_H TLP176 EXT_ALM_NO_H EXT_ALM EXT_ALM_C Alarm Acknowledge P12V TLP185 1.
APPENDIX 2 DIGITAL INTERFACE Blue Sign P12V TLP185 1.2kΩ RD BLUESIGN_H BLUESIGN_C Sentence description Input sentences ABM - Addressed binary and safety related message !**ABM, x, x, x, xxxxxxxxx, x, x.x, s--s, x, *hh 12 3 4 5 6 7 8 1. Total number of sentences needed to transfer the message (1 to 9) 2. Message sentence number (1 to 9) 3. Message sequence identifier (0 to 3) 4. The MMSI of destination AIS unit for the ITU-R M.1371 message (9 digits, NULL) 5.
APPENDIX 2 DIGITAL INTERFACE AIQ - Query sentence $**AIQ,ccc,*hh 1 1. Information requested (ACA*3, IWWIVD*1*2, IWWVSD*1*2, IWWSSD*1*2, PIWWIVD*2, PIWWVSD*2, PIWWSSD*2, SSD, TRL, TXT, VER, VSD) *1: Compatible with Tresco Inland ECDIS viewer. *2: Valid only when AIS is in INLAND mode. *3: When ACA is requested, ACS is also sent immediately after ACA. AIR - AIS interrogation request $**AIR,xxxxxxxxx,x.x,x,x.x,x,xxxxxxxxx,x.x,x, a, x.x, x.x, x.x *hh 1 2 3 4 5 6 7 8 9 10 11 12 1.
APPENDIX 2 DIGITAL INTERFACE GBS - GNSS satellite fault detection $**GBS, hhmmss.ss, x.x, x.x, x.x, xx, x.x, x.x, x.x h, h, *hh 1 2 3 4 5 6 7 8 9 10 1. UTC time of GGA or GNS fix associated with this sentence 2. Expected error in latitude (0.0 to 999.9) 3. Expected error in longitude (0.0 to 999.9) 4. Expected error in altitude (no use) 5. ID number of most likely failed satellite (no use) 6. Probability of missed detection for most likely failed satellite (no use) 7.
APPENDIX 2 DIGITAL INTERFACE GNS - GNSS fix data $**GNS,hhmmss.ss,llll.ll,a,IIIII.II,a,c--c,xx,x.x,x.x,x.x,x.x,x.x,a*hh 1 2 3 4 5 6 7 8 9 10 11 12 13 1. UTC of position (0.00 to 235959.99) 2. Latitude (0.00000 to 9000.00000) 3. N/S 4. Longitude (0.00000 to 18000.00000) 5. E/W 6. Mode indicator (A=Autonomous, D=Differential, E=Estimated Mode, F=Float RTK, M=Manual Input Mode, N=No fix, P=Precise, R=Real Time Kinematic, S=Simulator Mode) 7. Total number of satellites in use (Not used) 8.
APPENDIX 2 DIGITAL INTERFACE LRI - Long-range interrogation $**LRI,x,a,xxxxxxxxx,xxxxxxxxx,llll.ll,a,yyyyy.yy,a,llll.ll,a,yyyyy.yy,a*hh 12 3 4 5 6 7 8 1. Sequence number (0 to 9) 2. Control flag 3. MMSI of requestor 4. MMSI of destination 5. Latitude - N/S for north-east corner (0000.0000 to 9000.0000, NULL) 6. Longitude - E/W for north-east corner (0000.0000 to 18000.0000, NULL) 7. Latitude - N/S for south-west corner (0000.0000 to 9000.0000, NULL) 8. Longitude - E/W for south-west corner (0000.
APPENDIX 2 DIGITAL INTERFACE SSD - AIS ship static data $**SSD,c--c,c--c,xxx,xxx,xx,xx,c, aa*hh 1 2 3 4 5 67 8 1. Ship's call sign (1 to 7 characters, NULL) 2. Ship's name (1 to 20 characters, NULL) 3. Pos. ref. point distance, "A," from bow (0 to 511 Meters, NULL) 4. Pos. ref. point distance, "B," from stern (0 to 511 Meters, NULL) 5. Pos. ref. point distance, "C," from port beam (0 to 63 Meters, NULL) 6. Pos. ref. point distance, "D," from starboard beam (0 to 63 Meters, NULL) 7.
APPENDIX 2 DIGITAL INTERFACE Output sentences ABK - AIS addressed and binary broadcast acknowledgment $**ABK,xxxxxxxxx,x,x.x,x,x,*hh 1 2 3 45 1. MMSI of the addressed AIS unit 2. AIS channel of reception 3. Message ID 4. Message sequence number 5. Type of acknowledgement ACA - See “ACA - AIS regional channel assignment message” on page AP-5. ACS - Channel management information source $**ACS,x,xxxxxxxxx,hhmmss.ss,xx,xx,xxxx,*hh 1 2 3 4 5 6 1. Sequence number (0 to 9) 2.
APPENDIX 2 DIGITAL INTERFACE ALF - Alert sentence $**ALF,x,x,x,hhmmss.ss,a,a,a,aaa,x.x,x.x,x.x,x,c--c,*hh 123 4 5 6 7 8 9 10 11 12 13 1. Total number of ALF sentences for this message (1, 2) 2. Sentence number (1, 2) 3. Sequential message identifier (0 to 9) 4. Time of last change (hhmmss.ss, NULL) 5. Alert category (B=Category B, C=Category C, NULL) 6. Alert priority (W=Warning, C=Caution, NULL) 7.
APPENDIX 2 DIGITAL INTERFACE LRF - See “LRF - Long-range function” on page AP-8. LR1 - Long-range reply with destination for function request “A” $**LR1,x,xxxxxxxxx,xxxxxxxxx,c--c,c--c,xxxxxxxxx*hh 1 2 3 4 5 6 1. Sequence number 2. MMSI of responder 3. MMSI of requester (reply destination) 4. Ship's name (1 to 20 characters) 5. Call sign (1 to 7 characters) 6. IMO number, (9-digit number) LR2 - Long-range reply for function requests “B, C, E, and F” $**LR2,x,xxxxxxxxx,xxxxxx,hhmmss.ss,llll.
APPENDIX 2 DIGITAL INTERFACE TRL - AIS transmitter non functioning log $**TRL,x.x,x.x,x,xxxxxxxx,hhmmss.ss,xxxxxxxx,hhmmss.ss,x,*hh 1 2 3 4 5 6 7 8 1. Total number of log entries (0 to 10) 2. Log entry number (1 to 10, NULL) 3. Sequential message indentifier (0 to 9, NULL) 4. Switch off date (ddmmyyyy, NULL) 5. Switch off UTC time (000000 to 235959, NULL) 6. Switch on date (ddmmyy, NULL) 7. Switch on UTC time (000000 to 235959, NULL) 8.
APPENDIX 2 DIGITAL INTERFACE Inland AIS specific sentences Input sentences and output sentences PIWWIVD - Inland waterway voyage data $PIWWIVD x, x, x, xx.xx, xx.xx, x , xxx, xxxx, xxx, x.x, x.x, x.x, x.x, hh 1 2 3 4 5 6 7 8 9 10 11 12 13 1. Reporting rate: 0 to 15, NULL (See table to the right) 2. No. of blue cones: 0 to 3, 4=B-Flag, 5=unknown (default), NULL 3. Loaded/unloaded: 1=loaded, 2=unloaded, 0=not available (default), NULL 4. Inland draught: 0.01 to 20.00(m), 0=unknown (default), NULL 5.
APPENDIX 2 DIGITAL INTERFACE Output only sentence PIWWSPR - Inland AIS security password response $PIWWSPR a, x, x, x, hh 1 2 3 4 1. Mode (E: Password input, C: Password change) 2. Password level (1: Maintenance password, 2: User password, NULL) 3. Valid time (0 to 60 (s), NULL) 4.
1 $ 0 ( 81,7 1 $ 0 ( 81,7 ,167$//$7,21 0$18$/ (1 ഛせ㡿᭩ ⱥ 23(5$725 6 *8,'( (1 ᧯సせ㡿᭩ ከゝㄒ 23(5$725 6 0$18$/ (1 ྲྀᢅㄝ᫂᭩ ⱥ ᅗ᭩ ,167$//$7,21 0$7(5,$/6 ᕤᮦᩱ &$%/( $66(0%/< 㺗㺎㺪㺼㺷 ⤌ရ ᕤᮦᩱ 63$5( 3$576 ணഛရ ணഛရ $17(11$ 81,7 㺏㺻㺡㺣 2 8 7 / , 1 ( '2&80(17 ,167$//$7,21 0$7(5,$/6 63$5( 3$576 021,725 81,7 &203/(7( 6(7 ⾲♧㒊୍ᘧ⟽ワရ 75$16321'(5 81,7 㺢㺵㺻㺛㺬㺽㺻㺞㺼㒊 ࣘࢽࢵࢺ )$ ( *3$ 㹎㸿㹁㹉㹇㹌㹅ࠉ㹊㹇㹑㹒 ,0( 0/* 20( &3
1 $ 0 ( 81,7 '2&80(17 ,167$//$7,21 0$7(5,$/6 2 8 7 / , 1 ( ,0( 0/* 20( &3 )$ )$ '(6&5,37,21 &2'( θ 䠄␎ᅗ䛾ᑍἲ䛿䚸ཧ⪃್䛷䛩䚹㻌㻌㻰㻵㻹㻱㻺㻿㻵㻻㻺㻿㻌㻵㻺㻌㻰㻾㻭㼃㻵㻺㻳㻌㻲㻻㻾㻌㻾㻱㻲㻱㻾㻱㻺㻯㻱㻌㻻㻺㻸㼅㻚䠅 4 7< A-3 & = $ (6 ; 䡶㻙䢀䢚␒ྕᮎᑿ䛾㼇㻖㻖㼉䛿䚸㑅ᢥရ䛾௦⾲䡶䡬䢀䢚䜢⾲䛧䜎䛩䚹 㻯㻻㻰㻱㻌㻺㼁㻹㻮㻱㻾㻌㻱㻺㻰㻵㻺㻳㻌㼃㻵㼀㻴㻌㻎㻖㻖㻎㻌㻵㻺㻰㻵㻯㻭㼀㻱㻿㻌㼀㻴㻱㻌㻯㻻㻰㻱㻌㻺㼁㻹㻮㻱㻾㻌㻻㻲㻌㻾㻱㻼㻾㻱㻿㻱㻺㼀㻭㼀㻵㼂㻱㻌㻹㻭㼀㻱㻾㻵㻭㻸㻚 ,167$//$7,21 0$18$/ (1 ഛせ
1 $ 0 ( & = $ 4 7< 1 $ 0 ( ,167$//$7,21 0$7(5,$/6 ᕤᮦᩱ ᕤᮦᩱ *36 9+) &20%,1(' $17(11$ 」ྜ✵୰⥺㒊 ࣘࢽࢵࢺ 2 8 7 / , 1 ( ,167$//$7,21 0$7(5,$/6 81,7 *9$ 7 *9$ 7 +. 㹎㸿㹁㹉㹇㹌㹅ࠉ㹊㹇㹑㹒 &3 *9$ 7 +.
1 $ 0 ( 2 8 7 / , 1 ( ,167$//$7,21 0$7(5,$/6 81,7 &3 )$ '(6&5,37,21 &2'( θ 䠄␎ᅗ䛾ᑍἲ䛿䚸ཧ⪃್䛷䛩䚹㻌㻌㻰㻵㻹㻱㻺㻿㻵㻻㻺㻿㻌㻵㻺㻌㻰㻾㻭㼃㻵㻺㻳㻌㻲㻻㻾㻌㻾㻱㻲㻱㻾㻱㻺㻯㻱㻌㻻㻺㻸㼅㻚䠅 4 7< A-7 & = $ (6 ; 䡶㻙䢀䢚␒ྕᮎᑿ䛾㼇㻖㻖㼉䛿䚸㑅ᢥရ䛾௦⾲䡶䡬䢀䢚䜢⾲䛧䜎䛩䚹 㻯㻻㻰㻱㻌㻺㼁㻹㻮㻱㻾㻌㻱㻺㻰㻵㻺㻳㻌㼃㻵㼀㻴㻌㻎㻖㻖㻎㻌㻵㻺㻰㻵㻯㻭㼀㻱㻿㻌㼀㻴㻱㻌㻯㻻㻰㻱㻌㻺㼁㻹㻮㻱㻾㻌㻻㻲㻌㻾㻱㻼㻾㻱㻿㻱㻺㼀㻭㼀㻵㼂㻱㻌㻹㻭㼀㻱㻾㻵㻭㻸㻚 ,167$//$7,21 0$7(5,$/6 ᕤᮦᩱ ᕤᮦᩱ 021,725 81,7 ⾲♧㒊 ࣘࢽࢵࢺ )$ +.
D-1 Feb.
D-2 Feb.
Jan.
D-4 Mar.27'07 R.
16/Apr/2015 H.
16/Apr/2015 H.
16/Apr/2015 H.
D-8 16/Apr/2015 H.
16/Apr/2015 H.
1 2 GPSアンテナ GPS ANTENNA GPA-017S 選択 SELECT *2 M-P-7 TNC-J-3 複合空中線部 GPS/VHF ANTENNA GSC-001 GPA-020S *1 RG-10/UY N-J-3 1m 分配器 VHF ANT DISTRIBUTOR TNC-P-3 1m DB-1 GPS ANT *1 TTYCSLA-1,MAX.100m *1 TTYCSLA-1,MAX.100m サイレントスイッチ SILENT SWITCH レーダー/ECDIS STP(CAT5) *1 RADAR/ECDIS スイッチングハブ 3 100-230VAC NR203PF-VVS1.25 SWITCHING HUB 3.5m,φ8.6 1φ,50/60Hz HUB-100 8 *1 IV-2sq. 24VDC DPYC-2.