Furrion Digital Wireless Camera System Designed for 5th Wheel, RV, Caravan and Trailer applications Furrion’s new easy install wireless camera kit comes in two parts, 1. Furrion mount bracket prep kit. Part No. FRCBRKT-BL 2. Furrion Camera and Monitor Kit. Part No. FRC12TA-BL Check if your RV or Trailer has been pre installed with the mounting bracket prep kit.
Contents: 1. Safety Information 2. General Information 3. Installation instructions 4. Operation 5. Trouble shooting 6. Warranty 7.
Safety Instructions Please Read these instructions carefully before installation and operating your Furrion reversing camera unit. 2 The following symbols are used throughout this manual to indicate potentially dangerous situations or mark important safety instructions. WARNING: Indicates a potentially dangerous condition. Use extreme caution when performing this task. CAUTION: Indicates a critical procedure for safe and proper operation of the controller.
Caution: A battery or 12V DC electrical system presents a risk of electrical shock or burn hazard. Ensure all power sources are isolated before installation. Warning: These installation instructions are for the use by qualified personnel only. To reduce the risk of electric shock, do not perform any servicing other than that specified in the operating instructions. Caution: To reduce the risk of fire, connect the camera only to a circuit provided with a maximum branch-circuit over current protection device.
Installation Safety Precautions Use correct size cable and connectors for suppling power to your rear camera 4 Ensure the power supply circuit has circuit protection Connect rear camera to a 12-14V DC circuit only Use insulated tools when working with power supply Use correct safety equipment when working at elevated levels Ensure camera prep bracket gasket is correctly sealed and weatherproof.
General information Overview: Thank you for purchasing a Furrion reversing camera system. Furrion’s reversing camera system is one of the easiest rear view camera systems to install in your trailer, truck or RV. All that is required is a connection of a single DC power supply to the rear camera from a reversing power source. The Furrion reversing camera system is using digital wireless technology giving the major benefit of superior signal transmission with low interference on a single bandwidth channel.
Installation FRCBRKT-BL Furrion reversing camera mounting bracket installation: 6 The Furrion reversing camera prep kit includes: 1 x Reversing camera mounting bracket 1 x Mounting bracket gasket 1 x 6ft power cable 1 x Removable Bracket cover When wiring the Furrion camera system as a reversing camera, the power supply for the camera must come from a reversing indication power source (backup lights) or transmission wiring.
Mounting and wiring the camera prep bracket kit Wiring: For using your camera kit as a reversing camera system: 1. Isolate the 12V power system 7 2. To provide power to the wireless camera for use as a reversing camera, run a 2 core 16AWG internal cable from your reversing (back up) light on the rear of your trailer, truck or RV, or from your 7 way cable reversing power supply. (7way reversing connections.. center pin #7 positive + Ground pin #1 negative). 3.
Mounting bracket installation 8 Feed connector through PVC gasket 5/8” Hole Use 4 screws to fix mounting bracket to back of trailer or RV Ensure the bracket is mounted securely and the gasket is watertight. Affix cover if only prep kit is being installed * If the camera bracket is being mounted as a prep kit without the camera. secure the wire connector inside the bracket and attached the cover.
Installation of camera If your RV or trailer has a Furrion reversing camera prep kit pre installed by the OEM manufacturer. You will need to contact your local dealer or go to furrion.com to purchase a Furrion FRC12TA-BL Camera and monitor installation kit. To install the camera onto a pre installed mounting bracket: 1. Remove the cable cover which is held by 4 screws on the underside of the bracket 2. Locate the connector inside the prep kit mounting bracket 3.
Monitor Installation When choosing a location to mount the monitor, make sure the monitor is in an area that will not obstruct your vision while driving. 10 1. 2. 3. Before mounting the monitor, clean the mounting surface well. Position the suction mount to the smooth surface which suits your requirement. Press the suction cap against the smooth surface and press the lock down to attach and fix the mount to the surface. Snap in the monitor to the suction mount. 4.
Operation Once you have fitted the camera to your trailer, RV, truck or caravan you will need to pair the wireless camera with the LCD monitor before use. (This is only required at initial system comissioning to pair the camera with the LCD screen.
If there is no operation of the camera displayed on the LCD display within 30 seconds of pairing. Repeat pairing process. 12 Note: If you are having trouble pairing the devices, reduce the distance between the camera unit and the LCD display for the pairing process. To remove or replace a paired camera from the LCD display memory, Exit the menu icons on the LCD display, then press and hold down the DOWN key for 5 seconds. This will erase all pairing memory stored on the LCD display.
Trouble Shooting Monitor will not turn on Ensure power cord is connected to the display correctly Make sure the cigarette socket has power output of 12 - 14V DC Check fuse in cigarette socket adapter Camera and display will not pair Check if camera unit is recieving power Reduce the distance between camera and monitor while pairing Ensure to hold the pairing button on the camera for 2 seconds This icon flashes on the display: (intermittent / weak signal) Check antenna is installed correctly on camera
Technical specification of LCD Display: 14 1. Working voltage: DC12/24V 2. Working current: ≤180mA 3. Standby current: ≤5mA 4. Wireless communication distance: ≥100M (open area outdoors) 5. Working frequency: 2.4G 6. Size of LCD display: 4.3’ 7. Effective pixels of LCD: 480*272 8. Sensitivity of receiver: -87±3dBm 9. Working temperature: -10/+50 Technical specification of Camera unit: 1. Working voltage: DC12/24V 2. Working current: ≤220mA 3. Transmitting distance: ≥100M (open area outdoors) 4.
FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.