Digital Wireless Observation System Operating and Installation Instructions This manual is for use with Furrion FOS48TA-BL Digital Wireless Observation System Furrion FOS48TAPK-BL Digital Wireless Observation System With FRCBRKT-BL Mounting Bracket pre-installed.
Welcome Furrion FOS48TAPK-BL Digital Wireless Observation System Includes FRCBRKT-BL Mounting Bracket Furrion FRCBRKT-BL Digital Wireless Observation System For vehicles with FRCBRKT-BL Mounting Bracket pre-installed. Thank you for purchasing a Furrion Digital Wireless Observation System. Furrion’s digital wireless observation system is one of the easiest rear view camera systems to install in your trailer, truck or RV.
Contents IMPORTANT SAFETY INSTRUCTIONS.................................................................4 System Parts............................................................................................................5 Installation Mounting Bracket...................................................................................6-7 Installation Camera Wiring..........................................................................................7 Installation Mounting Bracket cont.................
IMPORTANT SAFETY INSTRUCTIONS READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR USING THE SYSTEM Electrical Safety Installation A battery or 12 or 24V DC electrical system presents a risk of electrical shock or burn hazard. Ensure all power sources are isolated before installation. Installation & wiring of this product require specialist skill. To ensure proper installation and to ensure safety, please seek a specialist technician. Insulate unconnected wires with vinyl tape or similar.
System Parts FOS48TAPK-BL Digital Wireless Observation System LCD Monitor Monitor Stand Monitor Power Cable Camera FRCBRKT-BL Digital Wireless Observation System Camera Bracket Camera Bracket Gasket Camera Power Cable 5
Installation Mounting Bracket (If the FRCBRKT-BL Mounting is pre-installed please go to page 9) Caution • E nsure there are no electrical cables, gas lines, pipes or other important parts behind where the drill holes will be. • During installation, remove the key from the ignition & isolate the 12v or 24v power source. Suitable installation position • W here practical, as high as possible at the rear of the vehicle. • I n the horizontal centre of the vehicle or as close as.
Installation Mounting Bracket 1 Use the Bracket Gasket to mark and outline where the centre hole will be drilled then drill a 5/8th” hole. 2 Feed the supplied 6ft Camera Power Cable through the gasket. Ensure the bare wire end of the cable goes into the vehicle and the flat side of the gasket faces inward.
Installation Mounting Bracket 3 Mount the gasket & bracket to the rear of the vehicle. Ensure that the Camera Power Cable does not get caught between the vehicle wall & gasket or the Bracket & Gasket. 3 Fix the Gasket & Bracket to the rear of the vehicle using 4 x #2 head 3/4” self tapping screws. (other screws can be used depending on side wall material.) Ensure the sealing lip around the edge of the gasket is seated over the edge of the bracket before fully tightening the screws.
Installation Camera Installation FRCBRKT-BL Pre-install only If installing to a pre-installed FRCBRKT-BL Mounting Bracket, remove the cover by unscrewing the 2 screws. 1 Locate the Camera Power Con- 2 Ensure the camera antenna is nector from within the Bracket and connect it to the Camera Plug. secured tight. 2 Secure the camera to the Bracket using the 4 screws.
Installation Camera Positioning The camera can be tilted up & down to obtain the best viewing angle. Positioning the Camera • Adjust the camera up or down then check the view via the monitor. • If the camera is to be used as parking camera, part of the vehicle, such as the bumper, should be visible on the monitor.
Installation Monitor Installation Positioning the Monitor • Ensure the the is placed so that it does not obstruct vision when driving. • Do not place in an area where it might interfere with driving. • The surface area should be clean, smooth & flat. With the lock open, position the mount. Press mount down against the surface. Adjusting the View Angle • Swivel & Tilt the mount to set the optimum viewing angle. • Lock the position by tightening the locking screws. 1 Push the mount lock down.
Operation Pairing After installation, the camera & monitor need to be paired. This only needs to be done once. Menu Up Menu/ Return Up Power/ Confirm Down Line Down Line Pairing procedure Ensure both the camera and monitor have power supplied. The vehicle may need to be running 1. Bring the monitor to within close proximity for pairing. 2. Press the Power button to turn on the monitor. 3. Press the Menu button, this will bring up 4 icons on the screen. 4.
Operation Pairing PAIRING FAILED will appear on the monitor after 13 seconds if the pairing procedure has been unsuccessful. *For better pairing results, bring the monitor closer to the camera. Unpairing To unpair the camera from the monitor, exit the menu, press & hold Down for 5 seconds. Picture Control Using the Up & Down buttons to navigate and adjust and the Power/ Confirm button to confirm selections, the monitors view settings can be adjusted to suit various viewing preferences.
Troubleshooting Problem Solution / Issue Monitor won’t turn on -Check that power cable is connected -Check the cigarette lighter has 12-14V DC Output -Check the fuse in the cigarette socket adaptor Camera & Monitor won’t pair -Check if the camera is receiving power -Reduce the distance between the camera & moni tor during pairing. -Make sure to hold the camera pairing button for 2 seconds. Intermittent/ Weak signal icon appears correctly - it should be vertical.
Camera Monitor Voltage DC8-30V DC8-30V Current ≤300mA ≤200mA ≤300M (outdoors) ≤300M (outdoors) Standby Current Wireless Range ≤1mA Wireless Frequency Image Sensor 2.4Ghz 1/4” Color CMOS VGA LCD Display Camera 4.3” 480*272 Max 25frames/sec VGA f1.7mm, F2.0 IR View Distance ≥1.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.