SERVICE MANUAL N4S Paka paka machine FCC ID:2AUBO43014 Model:43014 Isuue date: Aug. 27, 2019 Caution ★ Please read the manual carefully and keep it in mind before using this machine . ★ Put this manual within touch of your reference in anytime .
Thefollowingsafetyprecautionsaregiventhroughout thismanual.Theymustbestrictlyfollowedtoprotect those who install,use or maintain thisproduct as well as toprotect players, visitors and property. When setting up the machine, be sure to consult industry experts. It is not possible to set up machines for people other than industry experts. When installing this product, make sure that four feet are evenly placed on the floor, and ensure that the product is installed in a stable horizontal position.
CONTENTS 1.DIMENSION·····························P04 2.SPECIFICATION····························· P04 3.NAME OF PARTS····························· P04 4.LABEL LOCATION···························· · P07 4-1CAUTION LABEL LOCATION······················ ·· · ·· P07 4-2FUCTION LABEL LOCATION······················ ·· · ·· P09 5.COMPOMENTS·····························P10 6.
1. DIMENSION 2．SPECIFICATION DIMENSION（W*D*H） 500*635*2030(mm) PACKING DIMENSION（W*D*H） 680*600*1570（mm） GW(KG) 76.4KG NW(KG) 68.
3．NAME OF PARTS NO. PART NAME 1 PICTURE NO.
8 Capsule toy door NO. PART NAME 1 16 PICTURE wheel NO.
6 TYPE C 7 Power box 13 -7- Dial switch
4.
NO.
Maintenance outages 7 L100mm*W65mm 4-2 FUNCTION LABEL LOCATION NO.
2 Turn dial Ø127mm 3 Ground terminal L47mm*W37mm 4 Type A Ø50mm 5 Type B Ø50mm 6 Type C Ø50mm 7 Repair button Ø35mm 8 Set up L51mm*W27mm 5．COMPOMENTS NO. PART NAME 1 POWER LINE 2 3 PROTECTIVE TUBE MANUAL SPEC. QTY UNIT 1.
4 5 6 7 MACHINE KEYS LOCK KEYS HEXAGON WRENCH HEXAGON WRENCH LG01 2 pcs LG02 2 pcs 4mm 1 pcs 5mm 1 个 pcs - 12 -
6.INSTALLATION 6-1 INSTALLATION SPACE Need to have installation place. Maintenance Zone& Play zone should at least 1500mm*1600mm each. Once you set up the machine with required game-play area, when installing this product, set the 4 leg levelers evenly on the floor and make sure that the product is installed stably in a horizontal position.
CHOOSE THE 4PCS SCREW ,USE THE HEXAGON WRENCH CONNECT THE TUBE WITH BLACK BOARD. 3 4 HOLD THE TOP BOX WITH TUBE INSERTED BETWEEN THE HOLES. CHOOSE THE 4PCS SCREW ,USE THE HEXAGON WRENCH CONNECT THE TUBE WITH THE MAIN CABINET. 6-3 HOW TO FILL IN TOYS INTO TOP? 1 2 USE THE SCREWDRIVER LOOSEN THIS 4 PCS SCREW.
4 3 PUT CAPSULE TOYS INSIDE THE HOLE. SHOW AS FULL TOYS INSIDE .
7.
NO.
7-2 DIAL PART INSTALLATION DISGRAM Drawing after Installation - 18 -
NO. PART NAME 1 PICTURE SPEC QTY Hexagonal wire in round cup M4*16 1 2 dial Fluorescent Green Acrylic 1 SN.06-05 3 Dial bottom plate 6mm Milk-white nylon board 1 SN.06-06 4 Dial Rotating plate Q235 Galvanized 1 SN.02-05 5 Deep groove bearing 699ZZ 2 6 Dial bottom plate Q235 Galvanized 1 SN.02-06 7 Dial cushion gum Yellow polyurethane 1 SN.06-07 8 lock nut M4 3 9 circlip Ø8mm 2 10 Dial spring diameter 1.
7-3 CAPSULE TOYS STRUCTURE PART INSTALLATION DISGRAM - 20 -
NO. PART NAME 1 PICTURE SPEC QTY REMARK Cylindrical screw M6*175mm black 6 SN.09-04 2 90 Five-hole hood Yellow ABS 711 16 SN.07-01 3 Supporting rod fixing 201 Stainless steel 4 SN.03-14 4 Four-link Fixed Code for Support 201 Stainless steel 1 SN.03-15 5 Supporting rod fixing 201 Stainless steel 1 SN.03-14B 6 Large flat head machine silk M5*25mm Stainless steel 4 7 Token box clasp board 201 Stainless steel 1 8 Capsule button board 15mm black ABS 1 SN.
12 Axis of stud 201 Stainless steel 3 SN.02-01 13 Stud base plate Q235 4mm thick 3 SN.02-01 14 Single arm cushion plate Transparent organic tablets 5 SN.06-09 15 Spiral release shaft Yellow ABS 711 3 SN.07-02 16 Detection grating Electrolytic plate 1.5mm thick 3 SN.
7-4 TOP AND LIFT PART INSTALLATION DISGRAM NO. PART NAME 1 PICTURE SPEC QTY REMARK Main cabinet Q235 1 SN.03-10 2 lift Q235 1 SN.
5 Cylindrical head machine wire M6*30mm 2 6 1 Font connector 97*40mm 1 7 Countersunk machine wire M4*16mm 4 8 Combination yarn M5*25 10 9 Combination yarn M6*12 8 10 wheel 2.0 inch 2 8.HOW TO PLAY 1.Loop video 2. Click the “PUSH HERE TO START” button at the bottom right of the screen to enter the main menu 3. There are three interfaces providing for you to select; click the “VIEW SERIES” button to go to the purchase process; 4.
8-1 Loop video： Video 1 video 2 Video 3 Tip: click the “PSHU HERE TO START” button at the bottom right of the screen to enter the main menu when the video is showing 8-2 Main Menu: - 25 -
8-3 Purchase interface: Purchase interface No1: Purchase interface No 2 - 26 -
Purchase interface No3 8-4 Info interface: - 27 -
8-5 Purchase notification interface: 8-6 Capsule notification interface - 28 -
8-7 Setting interface: Attention: Before entering the setting interface, please use the key(key type: LG1) to open the front door and press the red button to enter the setting.
8-8 WIFI setting interface 8-9 Server IP address setting interface： - 30 -
8-10 Hardware test interface 8-11 Hardware test steps and errors handling Attention: Before entering the hardware testing interface, please follow the below steps one by one.
Click the “Hardware Test” button on the screen to enter the testing interface. Please don’t ignore the hardware test which is the operation core of the machine. The hardware has close relation with machine broken down. So please read this instruction seriously. The hardware test is mainly used to check whether above hardware works normally or not. The following below is to check whether each of hardware works or not.
8-12. Sensor ABC testing: Check whether each pipe has capsule or not and at least has one. Use LG01 key to open the screen door Hand touch to click the “Test Motor A” button If the Sensor A displays a red light and a new capsule coming out from the pipe, the sensor A is working. If the sensor A fails to run as normal, then need to replace the Senor.
loose 6 screws at Sensor A/B and remove the top two layers. loose the red and blue docking ports Slowly pull out the 5-hole cover on the 5th floor of Sensor A loosen two screws on the sheet metal surface with a screwdriver.
Slowly pull out the 5-hole cover on the third floor of Sensor A Slowly pull out the 5-hole cover on the second floor of Sensor A Select 5.5mm sleeve to loosen three nuts.
2. Capsule channel sensor testing: Watch if Counter 2 is bright red. Bright red indicates that the sensor is working normally. Two sensors on both sides of the inclined plate of the ball are shielded by hand (two on the left and two on the right). If the out-of-ball sensor does not work properly, a new sensor needs to be replaced. The replacement steps are as follows: Open the back door and use a screwdriver to loosen the back door screw. Turn off the machine.
Select a 5mm wrench to loosen the top six screws and take out the top two layers. Loosen the red and blue docking ports When the whole mechanism is lifted, it passes through three screw rods at the top, right and left, then according to this figure, move forward, and place the screw firmly in the slot clamp. Hands will be gifts mechanism parts lifted at the same time, to both sides of the screw position, it is best to operate both front and back at the same time.
Remove slope component status loose the three screws of the slope mechanism and remove them. 传感器 Replacem ent of sensors 3.coin selector test: Hand-ope rated SW1 key Watch for bright red at Coins. Bright red indicates that the coin operates normally.
If the coin selector is not working properly, a new coin must be replaced. The replacement steps are as follows: Pull the end of the wire by hand Choose the sleeve tool 7mm to loosen the four screws of the coin thrower. The operation can be completed by replacing the new coin holder. 4.SET UP BUTTON TEST: Watch if the Set is bright red.
If the button does not work properly, a new button needs to be replaced. The replacement steps are as follows: Remove the button docking terminal by hand. loose the button screw with an open wrench of 10 mm. Replacement of the new button will complete.
5. Error recover button test: Watch Repair for bright red. Bright red indicates that the button is working properly. Hold the button by hand 6.Dial test: Watch for bright red at TURN. Bright red indicates that the knob button is working properly.
If the knob does not work properly, the knob switch should be replaced. The replacement steps are as follows: Dial micro switch Release 2 screws with a screwdriver After pulling out the docking head. The new knob switch can be replaced.
9. APP Version Updating Method and Steps: Attention: firstly, make sure the machine power on stably; then following the below steps to update the APP version: press the red button Use the LG01 key to open the front door Mainboard Select the “Update App” option on the screen and wait 10s. The system will automatically update the latest App version. Insert the USB to host.
10.How to updated video Note: First of all, ensure that the machine is in a stable power-on state. Then update it through the following steps. As shown in the following figure: Select Key Model: LG01 Open the Door and Open the Front Door Press button mainboard Click Update Files on the screen and wait 10 seconds for the system to update automatically.
11. How to change the Mainboard? Separated the blue,red,white wire.
Move out the wooden board Find this four butterfly nut, loosen it ! Separated the mainboard plugs(five place). Use the screwdriver.lose the four screw ,and then change the mainboard .
12. CIRCUIT DIAGRAM Note: If the above illustrative pictures are changed, the physical machine is the standard.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
