User's Manual

ManualsBrandsFukuda Denshi ManualsElectronicsPatient Monitor

−

Basic Operation

This chapter describes the basic operation for monitoring.

Chapter 2

−

Before Use

−

Basic Operation for Monitoring

･

Touch Keys

･･････････････････････････････････

●

General Key Control

････････････････････････

●

Key Control for Each Parameter

･･････････････

−

Before Use

−

About the Home Display

･･････

About the Home Display

･･･････････････････････

The Description of the Display

･･････････････････

●

Numeric Data, Waveform, Patient Name, etc.

･･

●

Alarm Message for Numeric Data / Arrhythmia

･

●

Equipment Status Alarm Message

････････････

●

Other Bed Alarm Message

･･････････････････

To Return the Display

･････････････････････････

−

Preparation for Monitoring

−

To Turn On the Power

････････････････････････

Connecting the Power Cable

･･･････････････････

To Turn On the Power Switch

･･････････････････

To Use with the Battery Pack

･･････････････････

−

To Start Monitoring

− ･･･････････････････････

Discharge Confirmation at Power ON

･･････････

To Admit a Patient

･･･････････････････････････

− 

Basic Operation

− ･･････････････････････････

Scale, Lead, Baseline Position Setup

(Parameter Key)

････････････････････････････

Scale, Lead, Baseline Position Setup (User Key)

･

Alarm Setup for Each Parameter

･･････････････

ON/OFF of Parameter Display

Waveform/Numeric Data Display

･･････････････

Recording

･･････････････････････････････････

●

Start / Stop of Waveform Recording

･････････

To Install the Paper

･･････････････････････････

To Suspend Monitoring

･･･････････････････････

Discharging Procedure

･･･････････････････････

−

Operation Flow

− ･･･････････････････････････

Basic Operation

Summary of content (10 pages)

PAGE 1
Chapter 2 Basic Operation This chapter describes the basic operation for monitoring. 2 ● General Key Control ････････････････････････ 2 ● Key Control for Each Parameter ･･････････････ 2 About the Home Display ･･････ 3 − Before Use − About the Home Display ･･･････････････････････ 3 The Description of the Display･･････････････････ 4 − − − − ● Numeric Data, Waveform, Patient Name, etc.
PAGE 2
− Before Use − Basic Operation for Monitoring Touch Keys All the operation is performed using the touch keys on the screen. Always operate the touch screen with fingers or touch screen pen. Do not C A U T I O N touch with a pen-point or other hard-edged instruments. Malfunction of the touch screen or damage may result. ● General Key Control 2 3 1 1. Pressing the Menu key will switch the display with a pip sound. 2. The touch key will respond by pressing any part of the key. 3.
PAGE 3
− Before Use − About the Home Display About the Home Display ?The home display appears immediately after the power is turned ON. ?The waveforms and numeric data are displayed on the home display. ?There are 2 modes of home display, “Standard Display (Home)” and “Numeric Data Enlarged Display”, which can be switched by pressing the Home / Enlarge key. Reference Home 2 on the hospital Before Use The home key function can be selected from Home / Enlarge or setup menu. The default setting is Home .
PAGE 4
The Description of the Display Other than waveforms and numeric data, patient name, alarm message, status message, etc. will be displayed on the screen. ● Numeric Data, Waveform, Patient Name, etc. Bed ID Patient Name Patient Type Battery Capacity Time Telemetry Channel ID Numeric Data Display Area Parameter Key Waveform Display Area Fixed Key, User Key ● Alarm Message for Numeric Data / Arrhythmia There are 2 types of alarm messages, numeric data alarm message and arrhythmia alarm message.
PAGE 5
● Equipment Status Alarm Message The equipment status alarm message will be displayed when proper monitoring can not be performed. Equipment Status Alarm Message 2 ● Other Bed Alarm Message Before Use When the monitor is connected to the network, and other bed alarm is turned ON, the alarm occurring at the other bedside monitors will be notified. Other bed alarm message The other bed alarm message will function as a control key.
PAGE 6
To Return the Display 【To Return to the Home Display】 By pressing the Home key, the display will return to the home display. 【To Return to the Previous Display】 By pressing the Prev. Disp. key which will be displayed on each setup window, the previous display will appear.
PAGE 7
− Preparation for Monitoring − To Turn On the Power Connecting the Power Cable Connect the accompanying AC power cable (CS-34) to the monitor and to the 3-way grounded outlet. 2 Power Supply Connector Preparation for Monitoring When the AC power is supplied to the monitor, the main power lamp will light in green. Main Power Lamp This lamp will light in green when the AC power is supplied. The lamp will be extinguished during battery operation.
PAGE 8
Equipotential Grounding NOTE When connecting multiple devices, electrical potential difference may be generated between the devices. This may result in electric shock to the patient connected to these devices. Pay special attention for use in the operating room, ICU, CCU, Cardiac Catheter Laboratory, and Cardiovascular X-ray room. To avoid such electrical potential difference, use the accessory ground cable to connect each device’s equipotential terminal to the same ground terminal.
PAGE 9
To Use with the Battery Pack Unplug the power cable from the power supply connector located at the rear side of the monitor. If the power cable is unplugged with the power turned ON, the monitor will also automatically change to battery operation mode. Power Supply Connector 2 Power Supply Switch During battery operation, a battery mark will be displayed on the upper part of the display. Battery Mark Standard Mode Power Saving Mode Full 3 hours〜2 hours 20 min. 3 hours 30 min.〜2 hours 40 min.
PAGE 10
− To Start Monitoring − Discharge Confirmation at Power ON The monitor retains the trend and NIBP list data even when the power is turned OFF. If starting to monitor a new patient, discharge procedure on the patient admit / discharge menu should be performed. To start monitoring a new patient, press the Discharge key. The data before turning ON the power will be erased and starts monitoring. Pressing the Continue key will retain the data before turning ON the power and starts monitoring.