Design Technical Manual
Table Of Contents
- CHAPTER00
- CHAPTER01_General_information
- CHAPTER02_Model_selection
- 1. MODEL SELECTION PROCEDURE
- 2. MODEL LINE UP
- 3. MODEL SELECTION AND CAPACITY CALCULATION
- 4. CAPACITY TABLE COOLING (OUTDOOR UNIT)
- 5. CAPACITY TABLE HEATING (OUTDOOR UNIT)
- 6. CAPACITY COMPENSATION COEFFICIENT
- 7. CAPACITY TABLE COOLING (INDOOR UNIT)
- 7-1. COMPACT CASSETTE TYPE
- 7-2. CIRCULAR FLOW CASSETTE TYPE
- 7-3. CASSETTE TYPE
- 7-4. MINI DUCT TYPE
- 7-5. SLIM DUCT / SLIM CONCEALED FLOOR TYPE
- 7-6. MEDIUM STATIC PRESSURE DUCT TYPE
- 7-7. HIGH STATIC PRESSURE DUCT TYPE
- 7-8. VERTICAL AIR HANDLER TYPE
- 7-9. COMPACT FLOOR TYPE
- 7-10. FLOOR / CEILING TYPE
- 7-11. CEILING TYPE
- 7-12. WALL MOUNTED TYPE
- 8. CAPACITY TABLE HEATING (INDOOR UNIT)
- 8-1. COMPACT CASSETTE TYPE
- 8-2. CIRCULAR FLOW CASSETTE TYPE
- 8-3. CASSETTE TYPE
- 8-4. MINI DUCT TYPE
- 8-5. SLIM DUCT / SLIM CONCEALED FLOOR TYPE
- 8-6. MEDIUM STATIC PRESSURE DUCT TYPE
- 8-7. HIGH STATIC PRESSURE DUCT TYPE
- 8-8. VERTICAL AIR HANDLER TYPE
- 8-9. COMPACT FLOOR TYPE
- 8-10. FLOOR / CEILING TYPE
- 8-11. CEILING TYPE
- 8-12. WALL MOUNTED TYPE
- CHAPTER03_Outdoor_units
- CHAPTER04_Indoor_units
- CHAPTER05_Control_system
- 1. CONTROL SYSTEM
- 2. CONTROL UNITS
- 2-1. SYSTEM CONTROLLER
- 2-2. SYSTEM CONTROLLER LITE
- 2-3. TOUCH PANEL CONTROLLER
- 2-4. CENTRAL REMOTE CONTROLLER
- 2-5. WIRED REMOTE CONTROLLER (Touch panel)
- 2-6. WIRED REMOTE CONTROLLER
- 2-7. SIMPLE REMOTE CONTROLLER (With Operation mode)
- 2-8. SIMPLE REMOTE CONTROLLER (Without Operation mode)
- 2-9. WIRELESS REMOTE CONTROLLER
- 2-10. IR RECEIVER UNIT (for ALL DUCT TYPE)
- 2-11. IR RECEIVER UNIT (for CASSETTE TYPE)
- 2-12. IR RECEIVER UNIT (for CIRCULAR FLOW CASSETTE TYPE)
- 2-13. HUMAN SENSOR KIT (for CIRCULAR FLOW CASSETTE TYPE)
- 2-14. REMOTE SENSOR UNIT
- 2-15. PRESSURE SENSOR KIT
- 2-16. GROUP CONTROL METHOD
- 2-17. COMPARISON TABLE OF CONTROLLERS
- 3. ADAPTOR / CONVERTOR UNITS
- 4. SERVICE & WEB MONITORING TOOL
- CHAPTER06_System_design
- CHAPTER07_Function_setting
- CHAPTER08_External_input_and_output
- CHAPTER09_Notes
- CHAPTER10_Optional_parts
- CHAPTER99
LED105
CODE No.
Setting Mode
LED104
CODE No.
Setting Function
Factory
setting
Remarks
3 7
Outdoor
temperature
zone boundary
temperature
B
0 0 42.8°F (6°C)
l
Setting required if changing of the outdoor
temperature setting for heat pump only zone is
required when heater selection control using
outdoor temperature 1 is performed on the
indoor unit.
For details, refer to Chapter 8. 1-2-2.
EXTERNAL OUTPUT.
0 1 14.0°F (-10°C)
0 2 17.6°F (-8°C)
0 3 21.2°F (-6°C)
0 4 24.8°F (-4°C)
0 5 28.4°F (-2°C)
0 6 32.0°F (0°C)
0 7 35.6°F (2°C)
0 8 39.2°F (4°C)
0 9 42.8°F (6°C)
1 0 46.4°F (8°C)
1 1 50.0°F (10°C)
1 2 53.6°F (12°C)
1 3 57.2°F (14°C)
1 4 60.8°F (16°C)
1 5 64.4°F (18°C)
4 0
Capacity
priority setting
(in low noise
mode)
0 0 O (quiet priority)
l
If the cooling/heating performance becomes
insucient when the low noise mode is set,
it is possible to set “capacity priority” that
automatically cancels the low noise mode
(once performance is restored, the mode will
automatically return to the low noise mode).
0 1 On (capacity priority)
4 1
Low noise
mode setting
0 0 O (Normal)
l
0 1 On (Low noise mode)
4 2 Prohibited
0 0 Prohibited
l
Setting prohibited
0 1 Prohibited
6 0 Prohibited
0 0 Prohibited
l
Setting prohibited
0 1 Prohibited
6 1 Prohibited
0 0 Prohibited
l
Setting prohibited
0 1 Prohibited
- (07 - 85) -
FUNCTION
SETTING
FUNCTION
SETTING