Upgrade and Maintenance Manual - English PRIMERGY MX130 S2 Server Upgrade and Maintenance Manual Edition November 2011
Comments… Suggestions… Corrections… The User Documentation Department would like to know your opinion of this manual. Your feedback helps us optimize our documentation to suit your individual needs. Feel free to send us your comments by e-mail to manuals@ts.fujitsu.com.
Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure these safety notes are understood before using the product. Keep this manual and the manual "Safety Notes and Regulations" in a safe place for easy reference while using this product.
These uses include control of nuclear reactions in nuclear power plants, automatic airplane flight control, air traffic control, traffic control in mass transport systems, medical devices for life support, and missile guidance control in weapons systems (hereafter, "high safety use"). Customers should not use this product for high safety use unless measures are in place for ensuring the level of safety demanded of such use.
Contents Version history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 1.1 Where to find which information? . . . . . . . . . . . . . . . 18 1.2 Notational conventions 2 Before you start 2.1 2.1.1 2.1.2 2.1.3 Classification of procedures . . Customer Replaceable Units (CRU) Upgrade and Repair Units (URU) . Field Replaceable Units (FRU) . . 2.2 Average task duration . . . . . . . . . . . . . . . . . . . . .
Contents 4.3 Opening the front cage . . . . . . . . . . . . . . . . . . . . . 52 4.4 Closing the front cage . . . . . . . . . . . . . . . . . . . . . . 53 4.5 4.5.1 4.5.2 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 54 Mounting the server cover . . . . . . . . . . . . . . . . . . . . 54 Connecting the server to the mains . . . . . . . . . . . . . . . . 55 4.6 Switching on the server . . . . . . . . . . . . . . . . . . . . . 58 5 Basic software procedures . . . . . . . . . . .
Contents 7 HDDs and accessible drives . . . . . . . . . . . . . . . . . . 79 7.1 Basic procedure . . . . . . . . . . . . . . . . . . . . . . . . 81 7.2 Mounting order . . . . . . . . . . . . . . . . . . . . . . . . . 82 7.3 7.3.1 7.3.2 7.3.3 7.3.4 Installing 3.5-inch HDD in HDD1 / HDD2 chassis bay Required tools . . . . . . . . . . . . . . . . . . . . . . Preliminary steps . . . . . . . . . . . . . . . . . . . . Installing a 3.5-inch HDD in HDD 1/HDD 2 chassis bay . Concluding steps . . . . . . . . .
Contents 7.9 7.9.1 7.9.2 7.9.3 7.9.4 7.10 Installing additional 3.5-inch HDD in 5.25-inch ODD/HDD bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . Required tools . . . . . . . . . . . . . . . . . . . . . . . . Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . Installing an additional 3.5-inch HDD in ODD/HDD bracket . Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 103 103 104 106 7.10.4 Removing 3.5-inch HDD out of 5.25-inch ODD/HDD bracket . .
Contents 7.16 7.16.1 7.16.2 7.16.3 7.16.4 Removing slimline ODD out of 5.25-inch ODD/HDD bracket . . . . . . . . . . . . . . . . . . . . . . Required tools . . . . . . . . . . . . . . . . . . . . . . . . . Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . Removing a slimline ODD out of 5.25-inch ODD/HDD bracket Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 125 125 126 129 7.17 7.17.1 7.17.2 7.17.3 7.17.4 Installing backup drive in 5.
Contents 9 Expansion cards . . . . . . . . . . . . . . . . . . . . . . . . 159 9.1 Basic procedure . . . . . . . . . . . . . . . . . . . . . . . . 160 9.2 9.2.1 9.2.1.1 9.2.1.2 9.2.1.3 9.2.1.4 9.2.1.5 9.2.1.6 9.2.2 9.2.2.1 9.2.2.2 9.2.2.3 9.2.2.4 9.2.2.5 9.2.3 9.2.3.1 9.2.3.2 9.2.3.3 9.2.3.4 9.2.3.5 9.2.4 9.2.4.1 9.2.4.2 9.2.4.3 9.2.4.4 9.2.4.5 Expansion cards . . . . . . . . . . . . . . . . . . . . . . . Installing expansion cards . . . . . . . . . . . . . . . . . . Required tools . . . . . . . . . .
Contents 10.2 10.2.1 10.2.2 10.2.3 10.2.4 Installing memory modules Required tools . . . . . . . . Preliminary steps . . . . . . Installing a memory module . Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 182 182 182 183 10.3 10.3.1 10.3.2 10.3.3 10.3.4 Removing memory modules Required tools . . . . . . . .
Contents 12.2 Trusted Platform Module (TPM) . 12.2.1 Installing the TPM board . . . . . 12.2.1.1 Required tools . . . . . . . . . 12.2.1.2 Preliminary steps . . . . . . . 12.2.1.3 Installing the TPM board . . . 12.2.1.4 Concluding steps . . . . . . . 12.2.2 Removing the TPM board . . . . . 12.2.2.1 Required tools . . . . . . . . . 12.2.2.2 Preliminary steps . . . . . . . 12.2.2.3 Removing the TPM board . . . 12.2.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 14.1.1 Overview of used cables . . . . . . . . . . . . . . . . . . . . . 234 14.2 14.2.1 14.2.2 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 Power cabling . . . . . . . . . . . . . . . . . . . . . . . . . . 235 Data cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 14.3 14.3.1 14.3.2 14.3.3 14.3.4 14.3.5 Replacing the power cable Required tools . . . . . . . . Preliminary steps . . . . . . Removing the power cable . Installing the power cable . .
Contents 14 Upgrade and Maintenance Manual MX130 S2
Version history Issue number Reason for update Initial release MX130 S2 Upgrade and Maintenance Manual 15
Version history 16 Upgrade and Maintenance Manual MX130 S2
1 Introduction This Upgrade and Maintenance Manual provides instructions for the following procedures: ● Upgrading the server configuration by adding optional hardware components ● Upgrading the server configuration by replacing existing hardware components with superior ones. ● Replacing defective hardware components V CAUTION! The document at hand comprises procedures of a wide range of complexity. Check the profile of qualification for technicians before assigning tasks.
Introduction 1.1 Where to find which information? While the Upgrade and Maintenance Manual focuses on upgrade and maintenance procedures to bring the server back to normal operation, additional manuals provide detailed background information on server components and BIOS settings. For information on documents you need to have with you when leaving for maintaining a server see "Documents you need at hand" on page 28. I PRIMERGY manuals are available in PDF format on the ServerView Suite DVD 2.
Introduction 1.
Introduction 20 Upgrade and Maintenance Manual MX130 S2
2 Before you start Before you start any upgrade or maintenance task, please proceed as follows: Ê Carefully read the safety instructions in chapter "Important information" on page 31. Ê Make sure that all necessary manuals are available. Refer to the documentation overview in section "Documents you need at hand" on page 28. Print the PDF files if required. Ê Make yourself familiar with the procedure categories introduced in section "Classification of procedures" on page 23.
Before you start Please contact your local Fujitsu customer service partner for details on how to order expansion kits or spare parts. Use the Fujitsu Illustrated Spares Catalog to identify the required spare part and obtain technical data and order information. Illustrated Spares catalogs are available online at http://manuals.ts.fujitsu.com/illustrated_spares (EMEA market only).
Before you start 2.1 Classification of procedures The complexity of maintenance procedures varies significantly. Procedures have been assigned to one of three unit categories, indicating the level of difficulty and required qualification. At the beginning of each procedure, the involved unit type is indicated by one of the symbols introduced in this section. I Please ask your local Fujitsu service center for more detailed information. 2.1.
Before you start 2.1.2 Upgrade and Repair Units (URU) Upgrade and Repair Units (URU) Upgrade and Repair Units are non hot-plug components that can be ordered separately to be installed as options (Upgrade Units). Upgrade and repair procedures involve shutting down and opening the server. V CAUTION! The device may be seriously damaged or cause damage if it is opened without authorization or if repairs are attempted by unauthorized and untrained personnel.
Before you start 2.1.3 Field Replaceable Units (FRU) Field Replaceable Units (FRU) Removing and installing Field Replaceable Units involves complex maintenance procedures on integral server components. Procedures will require shutting down, opening and disassembling the server. V CAUTION! Maintenance procedures involving Field Replaceable Units must be performed exclusively by Fujitsu service personnel or technicians trained by Fujitsu.
Before you start 2.2 Average task duration Average task duration: 10 minutes The average task duration including preliminary and concluding steps is indicated at the beginning of each procedure next to the procedure class. Refer to table 1 on page 26 for an overview of steps taken into account for calculating the average task duration: Step included Explanation Server shutdown no Shutdown time depends on hardware and software configuration and may vary significantly.
Before you start 2.3 Tools you need at hand When preparing the maintenance task, ensure that all required tools are available according to the overview below. You will find a list of required tools at the beginning of each procedure. Screw driver / Bit insert Screw Phillips PH2 / (+) No. 2 hexagonal cross SW5 / PZ2 Usage Board, Front USB Type M3 x 4.5 mm (silver) C26192-Y10-C67 UNC 6-32 x 4.76 mm HDD3, HDD4 (black) Phillips PH2 / (+) No.
Before you start 2.4 Documents you need at hand Maintenance procedures may include references to additional documentation. When preparing the maintenance task, ensure that all required manuals are available according to the overview below. I– Ensure to store all printed manuals enclosed with your server in a save place for future reference. – Unless stated otherwise, all manuals are available online at http://manuals.ts.fujitsu.
Before you start Document Description Glossary available from the ServerView Suite DVD 2 or online at http://manuals.ts.fujitsu.com "Warranty" manual " 保証書 " for the Japanese market "Returning used devices" manual "Service Desk" leaflet " サポート＆サービス " for the Japanese market Third party documentation Important information on warranty regulations, recycling and service, available from the ServerView Suite DVD 2, online at http://manuals.ts.fujitsu.
Before you start 30 Upgrade and Maintenance Manual MX130 S2
3 Important information V CAUTION! Before installing and starting up a device, please observe the safety instructions listed in the following section. This will help you to avoid making serious errors that could impair your health, damage the device and endanger the data base. I Keep all manual and the other documentation (such as the technical manual, documentation DVD) close to the device. All documentation must be included if the equipment is passed on to a third party. 3.
Important information ● If the device is brought in from a cold environment, condensation may form both inside and on the outside of the device. Wait until the device has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the device if this requirement is not observed. ● Transport the device only in the original packaging or in packaging that protects it from knocks and jolts.
Important information ● Ethernet cabling has to comply with EN 50173 and EN 50174-1/2 standards or ISO/IEC 11801 standard respectively. The minimum requirement is a Category 5 shielded cable for 10/100 Ethernet, or a Category 5e cable for Gigabit Ethernet. ● Route the cables in such a way that they do not create a potential hazard (make sure no-one can trip over them) and that they cannot be damaged. When connecting the server, refer to the relevant instructions in this manual.
Important information ● Do not damage or modify internal cables or devices. Doing so may cause a device failure, fire, or electric shock and will void the warranty and exempt the manufacturer from all liability. ● Devices inside the server remain hot after shutdown. Wait for a while after shutdown before installing or removing internal options. ● The circuit boards and soldered parts of internal options are exposed and can be damaged by static electricity.
Important information Batteries ● Incorrect replacement of batteries may lead to a risk of explosion. The batteries may only be replaced with identical batteries or with a type recommended by the manufacturer. ● Do not throw batteries into the trash can. ● Batteries must be disposed of in accordance with local regulations concerning special waste. ● Make sure that you insert the battery the right way round. ● The battery used in this device may present a fire or chemical burn hazard if mistreated.
Important information 36 ● High humidity and airborne dust levels are to be avoided. Electric shocks and/or server failures may be caused by liquids such as water, or metallic items, such as paper clips, entering a drive. ● Shocks and vibrations are also to be avoided. ● Do not insert any objects other than the specified CDs/DVDs/BDs. ● Do not pull on, press hard, or otherwise handle the CD/DVD/BD tray roughly. ● Do not disassemble the ODD.
Important information I You can prevent damage from the ODD and the CDs/DVDs/BDs, as well as premature wear of the disks, by observing the following suggestions: – Only insert disks in the drive when needed and remove them after use. – Store the disks in suitable sleeves. – Protect the disks from exposure to heat and direct sunlight. Laser information The ODD complies with IEC 60825-1 laser class 1.
Important information ● Any devices or tools that are used must be free of electrostatic charge. ● Wear a suitable grounding cable that connects you to the external chassis of the system unit. ● Always hold components with ESDs at the edges or at the points marked green (touch points). ● Do not touch any connectors or conduction paths on an ESD. ● Place all the components on a pad which is free of electrostatic charge.
Important information 3.2 ENERGY STAR I Energy Star is applicable only for 230 V mains voltage. ENERGY STAR does not apply to the Japanese market. In typical configurations the PRIMERGY MX130 S2 satisfies the stringent requirements of the Ecolabel Energy Star for Computers Version 5.0. These requirements ensure energy savings when computers are being used and performing a range of tasks, as well as when they are turned off or into a low power mode.
Important information The system has a hibernate mode (S4 mode) from which it can be woken up via WOL (Wake-up On LAN). In order to use this feature, however, the S4 mode must be activated/enabled in the corresponding operating system installed. The following description is an example and can only serve as a guide for other operating systems.
Important information Exiting the hibernate/idle state (S4 mode) You switch on the system again either manually using the On/Off button or using the WOL function (WOL= Wake-up On LAN). To do this, a Magic Packet with the MAC address of the system to be woken up is sent to the internal LAN controller. You will find the valid MAC address for your device in the BIOS: Ê During boot press [F2] to enter BIOS. Ê Navigate to Main - System Information and press [Enter].
Important information 3.3 CE conformity The system complies with the requirements of the EC directives 2004/108/EC regarding "Electromagnetic Compatibility" and 2006/95/EC "Low Voltage Directive". This is indicated by the CE marking (CE = Communauté Européenne).
Important information 3.4 FCC Class A Compliance Statement If there is an FCC statement on the device, it applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation.
Important information 3.5 Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account. This saves resources and thus reduces the harm done to the environment.
Important information Labels on plastic casing parts Please avoid sticking your own labels on plastic parts wherever possible, since this makes it difficult to recycle them. Returns, recycling and disposal Please handle returns, recycling and disposal in accordance with local regulations. The device must not be disposed of with domestic waste. This device is labeled in compliance with European directive 2002/96/EC on waste electrical and electronic equipment (WEEE).
Important information 46 Upgrade and Maintenance Manual MX130 S2
4 Basic hardware procedures 4.1 Using diagnostics information The "PRIMERGY MX130 S2 Server Operating manual" gives an introduction to server features and provides an overview of available hardware options. Use the Fujitsu ServerView Suite management software to plan the upgrade or replacement of hardware components. ServerView Suite documentation is available online at http://manuals.ts.fujitsu.com or from the ServerView Suite DVD 2 supplied with your PRIMERGY server.
Basic hardware procedures 4.2 Opening the server V CAUTION! 4.2.1 ● Before removing or installing covers, turn off the server and all peripheral devices. Also unplug all power cables from the outlet. Failure to do so can cause electric shock. ● In order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and satisfy cooling requirements, the PRIMERGY MX130 S2 server must not run while the server cover is removed.
Basic hardware procedures / Figure 2: Power button on the front panel Ê Shut down the server. I If the system is running an ACPI-compliant operating system, pressing the On / Off button will perform a graceful shutdown. Disconnecting power cords Figure 3: Removing the power cord from the PSU Ê Disconnect the power cord from the PSU module.
Basic hardware procedures Only for Japan: Disconnecting cable tie Figure 4: Removing the cable tie Ê Pull out on the locking lever on the PSU cable tie (1) and loosen the loope (2). Ê Disconnect the power cord from the PSU module and remove it from the cable tie.
Basic hardware procedures 4.2.2 Removing the server cover Figure 5: Unlocking the locking bar Ê Slide the locking bar to the left until it rests in place. Figure 6: Removing the server cover Ê Push the server cover to the front. Ê Remove the server cover.
Basic hardware procedures 4.3 Opening the front cage Figure 7: Opening the front cage Ê Carefully fold open the front cage. I Pay attention to the SATA data cable, especially to the the slimline ODD SATA data cable when you fold open the front cage. If it is located in the additional 5.25-inch bracket, you have to disconnect the SATA data cable from the drive before fold open the front cage.
Basic hardware procedures 4.4 Closing the front cage Figure 8: Closing the front cage Ê Carefully close the front cage. V CAUTION! Ensure that none of the cables are strained or trapped! Ê If you loosened any cables tighten them again.
Basic hardware procedures 4.5 Closing the server V CAUTION! 4.5.1 ● Before attaching the covers, make sure no unnecessary parts or tools are left inside the server. ● In order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and satisfy cooling requirements, the PRIMERGY MX130 S2 server must not run while the server cover is removed. ● For further safety information, please refer to chapter "Important information" on page 31.
Basic hardware procedures Figure 10: Closing the server cover Ê Slide the server cover shut by engaging the locking mechanism. 4.5.2 Connecting the server to the mains The PRIMERGY MX130 S2 Server is equipped with a standard PSU. V CAUTION! The power supply automatically adjusts to any mains voltage in the range of 100 V - 240 V. You may only operate the server if its rated voltage range corresponds to the local mains voltage.
Basic hardware procedures Connecting power cord Figure 11: Connecting power cord Ê Connect the power cord to the power supply.
Basic hardware procedures Only for Japan: Connecting the cable tie Figure 12: Connecting the cable tie Ê Thread the cable tie through the eye (1). Ê Pull the cable tie tight to secure the power cord (2). The insulated connector cannot now be disconnected from the server accidentally.
Basic hardware procedures 4.6 Switching on the server V CAUTION! ● Before switching on the server, make sure the server cover is closed. In order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and satisfy cooling requirements, the PRIMERGY MX130 S2 server must not run while the server cover is removed. ● Follow the safety instructions in chapter "Important information" on page 31. Ê Connect all peripheral cables to the rear connector panel of the server.
5 Basic software procedures 5.1 Starting the maintenance task 5.1.1 Disabling BitLocker functionality BitLocker Drive Encryption provides protection for operating system and data drives by encrypting the contents and requiring users to authenticate their credentials to access the information. On the operating system drive, BitLocker uses the compatible Trusted Platform Module (TPM) to detect if the computer's startup process has been modified from its original state.
Basic software procedures I Administrator permission required: If you are prompted for an administrator password or confirmation, type the password or provide confirmation. Ê To temporarily disable BitLocker, click Turn Off BitLocker, and then click Disable BitLocker Drive Encryption. I In order to determine which features are accessible through the BitLocker setup wizard, modify the BitLocker Group Policy settings.
Basic software procedures 5.1.3 Verifying and configuring the backup software solution I This task only applies to the Japanese market. Depending on the backup software solution, it may be necessary to disable or delete the backup drive from the backup software drive list before starting the maintenance task. This is the case for the following backup software solution: – BackupExec I Procedures may differ depending on the backup software.
Basic software procedures 5.2 Completing the maintenance task 5.2.1 Updating the system board BIOS After replacing the system board, it is essential to upgrade the BIOS to the latest version. The latest BIOS versions are available from the Fujitsu support internet pages at: http://ts.fujitsu.com/support/ (EMEA market) http://primeserver.fujitsu.
Basic software procedures Ê Press the On / Off button to start up the server. The system will detect the USB stick and the BIOS recovery process will be performed. V CAUTION! Do not interrupt the BIOS upgrade process after it has started. If the process is interrupted, the system BIOS may be permanently corrupted. Ê After completion of the flash process, shut down the server. Ê Open the side cover as described in section "Closing the server" on page 54.
Basic software procedures 5.2.3 Enabling Option ROM scan In order to configure an expansion card that has been installed or replaced, the card’s Option ROM has to be enabled in the system board BIOS. The card’s firmware is called by the system BIOS upon reboot and can be entered and configured. Option ROM can be enabled permanently (e.g. in case of a boot controller that may require frequent setup) or temporarily for one-time configuration.
Basic software procedures I Procedures may differ depending on the backup software. For details, refer to the dedicated documentation provided separately. Further information on suitable backup software solutions and related documentation is available to Fujitsu service partners from the Fujitsu Extranet pages. Re-enabling backup drives If a backup drive has been disabled or deleted from the backup software drive list as described in section 5.1.
Basic software procedures 5.2.6 Enabling BitLocker functionality If BitLocker Drive Encryption has been disabled for maintenance purposes (see section "Disabling BitLocker functionality" on page 59), it has to be re-enabled to complete the service task. I If BitLocker Drive Encryption has been disabled prior to replacing components you won't be asked for a recovery key when rebooting the server after the maintenance task.
Basic software procedures 5.2.7 Performing a RAID array rebuild After replacing a hard disk drive that has been combined into a RAID array, RAID rebuild will be performed completely unattended as a background process. Figure 14: Progress bar (RAID array rebuild) V CAUTION! The system is now operational, however, data redundancy will not be available until the RAID array rebuild is complete.
Basic software procedures 5.2.9 Using the Chassis ID Prom Tool The Chassis ID EPROM located on the system board contains system information like server name and model, housing type, serial number and manufacturing data. In order to integrate your system into the ServerView management environment and to enable server installation using the ServerView Installation Manager, system data needs to be complete and correct.
6 Power supply Basic information The PRIMERGY MX130 S2 server is equipped with a standard PSU. V CAUTION! The server supports a mains voltage in the range of 100 V - 240 V You may only operate the server if its rated voltage range corresponds to the local mains voltage. Safety notes V CAUTION! ● Do not disassemble the PSU. Doing so may cause electric shock. ● Areas around the PSU may remain extremely hot after shutdown.
Power supply 6.1 Standard PSU 6.1.1 Replacing the standard PSU Field Replaceable Units (FRU) Average task duration: 10 minutes 6.1.1.1 Required tools ● Preliminary and concluding steps: tool-less ● Replacing the PSU: – Phillips PH2 / (+) No. 2 screw driver 6.1.1.2 Preliminary steps Before replacing the standard PSU, perform the following steps: I You are advised to perform this routine with the server in a horizontal position.
Power supply 6.1.1.
Power supply 6.1.1.4 Removing the PSU 0 / Figure 16: Removing the PSU Ê Remove four screws from the PSU (see circles). Ê Slide the defective PSU inward by 3 cm (1) to disengage the locking mechanism. Ê Lift the defective PSU out of the chassis (2).
Power supply 6.1.1.
Power supply Figure 18: Installing the standard PSU Ê Insert the PSU into the chassis leaving a gap of about 3 cm to the rear chassis wall (1) in figure 17. Ê Ensure that the mounting bracket on the chassis (see circle in figure 18) engages with the notch on the lower surface of the PSU. Ê Slide the new PSU towards the rear of the chassis (2) in figure 17.
Power supply Figure 19: Securing the PSU Ê Secure the PSU to the chassis with four screws (M3 x 4.5 mm, see circles).
Power supply 6.1.1.6 Reconnecting internal power cables Figure 20: Connecting internal power cables Ê Connect the PSU ATX power connector to system board connector POWER12V.
Power supply 6.1.1.7 Concluding steps Perform the following procedures to complete the task: Ê Follow all procedures described in section "Closing the server" on page 54. Ê If BitLocker functionality is used and has been disabled before starting the maintenance task, re-enable BitLocker as described in section "Enabling BitLocker functionality" on page 66.
Power supply 78 Upgrade and Maintenance Manual MX130 S2
7 HDDs and accessible drives Safety notes V CAUTION! ● The HDDs must all be marked clearly so that they can be put back in their original places after an upgrade. If this is not done, existing data can be lost. ● When a HDD is starting up, a resonant noise may be audible for a short while. This does not indicate a failure. ● Depending on the OS, you can configure the write cache settings for the HDDs. If a power failure should occur while the write cache is enabled, cached data may be lost.
HDDs and accessible drives ● Do not touch the circuitry on boards or soldered parts. Hold circuit boards by their metallic areas or edges. ● Circuit boards and soldered parts of internal options are exposed and can be damaged by static electricity. Always discharge static build-up (e.g. by touching a grounded object) before handling electrostaticsensitive devices (ESDs). ● For further safety information, please refer to chapter "Important information" on page 31.
HDDs and accessible drives ● "Installing backup drive in 5.25-inch chassis bay" on page 130 ● "Removing backup drive out of 5.25-inch chassis bay" on page 133 ● "Installing slimline ODD in slimline chassis bay" on page 136 ● "Replacing slimline ODD out of slimline chassis bay" on page 142 7.1 Basic procedure – HDDs with different capacities are installed from lowest to highest capacity. – HDDs with different rotation speeds are installed from lowest to highest speed.
HDDs and accessible drives 7.2 Mounting order Maximum configuration: 4 x 3.5-inch HDD + slimline ODD Slimline ODD HDD1 HDD4 HDD2 HDD3 Figure 21: Slimline ODD mounting order with 4 x 3.5-inch HDD HDD1 HDD2 HDD3 / RDX Slimline ODD Figure 22: Slimline ODD mounting order with 3 x 3.5inch HDD or 2 x 3.5inch HDD and RDX HDD1 HDD2 HH ODD / RDX HDD3 Figure 23: HH ODD or RDX mounting order with 3 x 3.
HDDs and accessible drives 7.3 Installing 3.5-inch HDD in HDD1 / HDD2 chassis bay Upgrade and Repair Units (URU) Average task duration: 5 minutes 7.3.1 Required tools ● Preliminary and concluding steps: tool-less ● Installing a 3.5-inch HDD: tool-less 7.3.2 Preliminary steps Before installing a 3.5-inch HDD, perform the following steps: Ê Follow all procedures described in section "Opening the server" on page 48. Ê Open the front cage as described in section "Opening the front cage" on page 52.
HDDs and accessible drives 7.3.3 Installing a 3.5-inch HDD in HDD 1/HDD 2 chassis bay Ê Detach and remove the Easy rails from the desired 3.5-inch HDD installation bay. Align the three pins on the Easy rails with the screw holes on the new HDD. Figure 24: Installing the Easy rail on the 3.
HDDs and accessible drives Figure 25: Inserting the 3.5-inch HDD Ê Insert the HDD into its installation bay.
HDDs and accessible drives Figure 26: Installing the 3.5-inch HDD Ê Slide the HDD into its installation bay until the locking latches engage.
HDDs and accessible drives 1 1 / 0 Figure 27: Connecting the cables Ê Connect the two SATA connectors to the HDDs (1 and 2). Ê Plug the cable with the green point to the upper HDD1. For orientation there is a second green point on the other end of this cable. Ê Connect the power connectors (3). 7.3.4 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page 53.
HDDs and accessible drives 7.4 Removing 3.5-inch HDD out of HDD1 / HDD2 chassis bay Upgrade and Repair Units (URU) Average task duration: 5 minutes 7.4.1 Required tools ● Preliminary and concluding steps: tool-less ● Removing a 3.5-inch HDD: tool-less 7.4.2 Preliminary steps Before removing a 3.5-inch HDD, perform the following steps: Ê Ensure that the HDD to be removed is not combined into a RAID array.
HDDs and accessible drives 7.4.3 Removing a 3.5-inch HDD out of HDD 1/HDD 2 chassis bay 0 / Figure 28: Disconnecting the cables from the a 3.5-inch HDD Ê Disconnect the power cable (2) and data cable (1).
HDDs and accessible drives / 0 / Figure 29: Removing a 3.5-inch HDD Ê Pull the two green handles of the Easy rails in the direction of arrow 1. Ê Pull the HDD with the two green handles of the Easy rails completely out of its bay (2). Figure 30: Inserting the Easy rails Ê Insert the Easy rails into the bay.
HDDs and accessible drives 7.4.4 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page 53. Ê Follow all procedures described in section "Closing the server" on page 54. 7.5 Installing additional 3.5-inch HDD in 3.5inch chassis bay Upgrade and Repair Units (URU) Average task duration: 5 minutes 7.5.1 Required tools ● Preliminary and concluding steps: tool-less ● Installing a 3.
HDDs and accessible drives 7.5.3 Installing an additional 3.5-inch HDD in 3.5-inch chassis bay Figure 31: Installing the HDD in 3.5-inch chassis bay Ê Insert the HDD into the drive bay and fasten the four screws (see circles).
HDDs and accessible drives / 0 Figure 32: Connecting the cables to the HDD Ê Connect cables to the HDD. 1 Power cable connector P3 (see "Power cable T26139-Y4012-V211" on page 239) 2 SATA cable T26139-Y4028-V153 7.5.4 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page 53. Ê Follow all procedures described in section "Closing the server" on page 54.
HDDs and accessible drives 7.6 Removing additional 3.5-inch HDD out of 3.5-inch chassis bay 7.6.1 Required tools ● Preliminary and concluding steps: tool-less ● Installing a 3.5-inch HDD – Phillips PH2 / (+) No. 2 screw driver 7.6.2 Preliminary steps Before installing a 3.5-inch HDD, perform the following steps: Ê Follow all procedures described in section "Opening the server" on page 48. Ê Open the front cage as described in section "Opening the front cage" on page 52.
HDDs and accessible drives 7.6.3 Removing an additional 3.5-inch HDD out of 3.5inch chassis bay / 0 Figure 33: Disconnecting the cables from the HDD Ê Disonnect cables from the HDD.
HDDs and accessible drives Figure 34: Removing the HDD from 3.5-inch chassis bay Ê Remove the four screws (see circles) and remove the HDD from the drive bay. 7.6.4 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page 53. Ê Follow all procedures described in section "Closing the server" on page 54.
HDDs and accessible drives 7.7 Installing additional 3.5-inch HDD in 5.25inch dummy cover 7.7.1 Required tools ● Preliminary and concluding steps: tool-less ● Installing a 3.5-inch HDD – Phillips PH2 / (+) No. 2 screw driver 7.7.2 Preliminary steps Before installing a 3.5-inch HDD, perform the following steps: Ê Follow all procedures described in section "Opening the server" on page 48. Ê Locate the correct drive bay as described in section "Mounting order" on page 82. Ê Remove the 5.
HDDs and accessible drives 7.7.3 Installing a 3.5-inch HDD in 5.25-inch dummy cover 0 / 0 Figure 35: Installing the HDD in the 5.25-inch dummy cover Ê Insert the HDD into the 5.25-inch dummy cover (1) and fasten the four screws (2). Figure 36: Connecting the fixation plate to the 5.25-inch dummy cover Ê Align the four pins of the fixation plate with the screw holes on the 5.25-inch dummy cover.
HDDs and accessible drives / Figure 37: Installing the 5.25-inch dummy cover with HDD into the chassis bay Ê Insert the 5.25-inch dummy cover with HDD in the bay (1) until it snaps into place. Ê Open the front cage as described in section "Opening the front cage" on page 52.
HDDs and accessible drives Ê Connect cables to the HDD. 1 Power cable connector P2 (see "Power cable T26139-Y4012-V211" on page 239) 2 SATA cable T26139-Y4028-V153 7.7.4 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page 53. Ê Follow all procedures described in section "Closing the server" on page 54. Ê Please observe the notes on RAID rebuild in section "Performing a RAID array rebuild" on page 67.
HDDs and accessible drives 7.8.3 Removing a 3.5-inch HDD out of 5.25-inch dummy cover / 0 Figure 39: Disconnecting the cables from the HDD Ê Disconnect cables from the HDD. 1 Power cable connector P2 (see "Power cable T26139-Y4012-V211" on page 239) 2 SATA cable T26139-Y4028-V153 Ê Close the front cage as described in section "Closing the front cage" on page 53.
HDDs and accessible drives / 0 Figure 40: Removing the 5.25-inch dummy cover with HDD out of the the chassis bay Ê Push the green handle backward (1) and remove the 5.25-inch dummy cover with HDD out of the the bay (2). / 0 / Figure 41: Removing the HDD out of the 5.25-inch dummy cover Ê Remove the four screws (1) and remove the HDD out of the 5.25-inch dummy cover (2).
HDDs and accessible drives V CAUTION! Always replace dummy modules into unused drive bays to comply with applicable EMC regulations and satisfy cooling requirements. 7.8.4 Concluding steps Perform the following procedures to complete the task: Ê Install the 5.25-inch dummy cover as described in section "Installing 5.25inch dummy cover" on page 110. Ê Follow all procedures described in section "Closing the server" on page 54. 7.9 Installing additional 3.5-inch HDD in 5.25inch ODD/HDD bracket 7.9.
HDDs and accessible drives 7.9.3 Installing an additional 3.5-inch HDD in ODD/HDD bracket 0 / 0 Figure 42: Installing the HDD in the 5.25-inch ODD/HDD bracket Ê Insert the HDD into the ODD/HDD bracket (1) and fasten the four screws (2). Figure 43: Connecting the fixation plate to the 5.25-inch ODD/HDD bracket Ê Align the four pins of the fixation plate with the screw holes on the ODD/HDD bracket.
HDDs and accessible drives / Figure 44: Inserting ODD/HDD bracket in 5.25-inch chassis bay Ê Insert the ODD/HDD bracket in the bay (1) until it snaps into place. Ê Open the front cage as described in section "Opening the front cage" on page 52. / 1 / 0 2 0 Figure 45: Cabling of HDD and ODD in 5.
HDDs and accessible drives Ê Connect cables to the HDD. 1 Power cable connector P2 (see "Power cable T26139-Y4012-V211" on page 239) 2 SATA cable T26139-Y4028-V153 Ê Connect cables to the ODD. 3 Power cable connector P4 (see "Power cable T26139-Y4012-V211" on page 239) 4 SATA cable T26139-Y4028-V201 7.9.4 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page 53.
HDDs and accessible drives 7.10.2 Preliminary steps Before installing a 3.5-inch HDD, perform the following steps: Ê Follow all procedures described in section "Opening the server" on page 48. Ê Open the front cage as described in section "Opening the front cage" on page 52. Ê Locate the correct drive bay as described in section "Mounting order" on page 82. 7.10.3 Removing an additional 3.5-inch HDD out of the 5.25-inch ODD/HDD bracket / 1 / 0 2 0 Figure 46: Cabling of HDD and ODD in 5.
HDDs and accessible drives Ê Disconnect cables to the ODD. 3 Power cable connector P4 (see "Power cable T26139-Y4012-V211" on page 239) 4 SATA cable T26139-Y4028-V201 Ê Close the front cage as described in section "Closing the front cage" on page 53. / 0 Figure 47: Removing the 5.25-inch ODD/HDD bracket Ê Push the green handle backward (1) and pull the ODD/HDD bracket out of its bay (2).
HDDs and accessible drives Figure 48: Removing the fixation plate from the 5.25-inch ODD/HDD bracket Ê Remove the fixation plate from the 5.25-inch ODD/HDD bracket. / 0 / Figure 49: Removing the HDD out of the 5.25-inch ODD/HDD bracket Ê Remove the four screws (1) and pull the HDD out of the 5.25-inch ODD/HDD bracket (2).
HDDs and accessible drives 7.10.4 Concluding steps Perform the following procedures to complete the task: Ê Install the 5.25-inch dummy cover as described in section "Installing 5.25inch dummy cover" on page 110. Ê Follow all procedures described in section "Closing the server" on page 54. 7.11 Installing 5.25-inch dummy cover 7.11.1 Required tools ● Preliminary and concluding steps: tool-less ● Removing the dummy cover: tool-less 7.11.
HDDs and accessible drives 7.11.3 Installing a 5.25-inch dummy cover Figure 50: Connecting the fixation plate to the 5.25-inch dummy cover Ê Align the four pins of the fixation plate with the screw holes on the 5.25-inch dummy cover. / Figure 51: Installing the 5.25-inch dummy cover Ê Insert the dummy cover in the bay (1) until it snaps into place.
HDDs and accessible drives 7.11.4 Concluding steps Perform the following procedures to complete the task: Ê Follow all procedures described in section "Closing the server" on page 54. 7.12 Removing 5.25-inch dummy cover Upgrade and Repair Units (URU) Average task duration: 5 minutes 7.12.1 Required tools ● Preliminary and concluding steps: tool-less ● Removing the dummy cover: tool-less 7.12.
HDDs and accessible drives 7.12.3 Removing a 5.25-inch dummy cover / 0 Figure 52: Removing the 5.25-inch dummy cover Ê Push the green handle backward (1) and pull the dummy cover out of its bay (2). V CAUTION! Always replace dummy modules into unused drive bays to comply with applicable EMC regulations and satisfy cooling requirements.
HDDs and accessible drives Figure 53: Removing the fixation plate of the 5.25-inch dummy cover Ê Remove the fixation plate from the dummy cover. V CAUTION! Save the fixation plate for future use. You have to install the fixation plate to the different drive cages before installation. 7.12.4 Concluding steps Perform the following procedures to complete the task: Ê Install the 5.25-inch dummy cover as described in section "Installing 5.25inch dummy cover" on page 110.
HDDs and accessible drives 7.13 Installing ODD in 5.25-inch chassis bay 7.13.1 Required tools ● Preliminary and concluding steps: tool-less ● Installing ODD: tool-less 7.13.2 Preliminary steps Before installing an ODD, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59. Ê Follow all procedures described in section "Opening the server" on page 48.
HDDs and accessible drives 7.13.3 Installing an ODD in 5.25-inch chassis bay Ê Connect the fixation plate to the ODD. / Figure 54: Installing HH ODD Ê Insert the half-height ODD in the bay (1) until it snaps into place. Ê Open the front cage as described in section "Opening the front cage" on page 52.
HDDs and accessible drives / 0 Figure 55: Connecting cables to the HH ODD Ê Connect cables to the HH ODD. 1 Power cable connector P2 (see "Power cable T26139-Y4012-V211" on page 239) 2 SATA cable T26139-Y4028-V102 7.13.4 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page 53. Ê Follow all procedures described in section "Closing the server" on page 54.
HDDs and accessible drives 7.14 Removing ODD out of 5.25-inch chassis bay 7.14.1 Required tools ● Preliminary and concluding steps: tool-less ● Installing an ODD: tool-less 7.14.2 Preliminary steps Before removing an ODD, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59.
HDDs and accessible drives 7.14.3 Removing an ODD out of 5.25-inch chassis bay / 0 Figure 56: Disconnecting cables of the HH ODD Ê Disconnect cables of the HH ODD. 1 Power cable connector P2 (see "Power cable T26139-Y4012-V211" on page 239) 2 SATA cable T26139-Y4028-V102 Ê Close the front cage as described in section "Closing the front cage" on page 53.
HDDs and accessible drives / 0 Figure 57: Removing HH ODD Ê Push the green handle backward (1) and pull the half-height ODD out of the bay (2). Ê Disconnect the fixation plate from the HH ODD cage. V CAUTION! Always replace dummy modules into unused drive bays to comply with applicable EMC regulations and satisfy cooling requirements. 7.14.4 Concluding steps Perform the following procedures to complete the task: Ê Install the 5.25-inch dummy cover as described in section "Installing 5.
HDDs and accessible drives 7.15 Installing slimline ODD in 5.25-inch ODD/HDD bracket 7.15.1 Required tools ● Preliminary and concluding steps: tool-less ● Installing a slimline ODD: – EMEA: Torx Plus Size 6 – Japan: Philips (+) No.00 screw driver 7.15.2 Preliminary steps Before installing a slimline ODD, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59.
HDDs and accessible drives 7.15.3 Installing a slimline ODD in 5.25-inch ODD/HDD bracket Figure 58: Installing the ODD in the 5.25-inch ODD/HDD bracket Ê Insert the ODD into its installation bay and carefully push in until the screw holes are matching. Figure 59: Fastening the screws Ê Fasten the three screws.
HDDs and accessible drives Figure 60: Connecting the fixation plate to the 5.25-inch ODD/HDD bracket Ê Align the four pins of the fixation plate with the screw holes on the 5.25-inch ODD/HDD bracket. / Figure 61: Installing the 5.25-inch ODD/HDD bracket with the slimline ODD Ê Insert the 5.25-inch ODD/HDD bracket with the ODD in the bay (1) until it snaps into place.
HDDs and accessible drives Ê Open the front cage as described in section "Opening the front cage" on page 52. / 0 Figure 62: Connecting cables of the slimline ODD in 5.25-inch ODD/HDD bracket Ê Connect cables to the slimline ODD. 1 Power cable connector P4 (see "Power cable T26139-Y4012-V211" on page 239) 2 SATA cable T26139-Y4028-V201 7.15.4 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page 53.
HDDs and accessible drives 7.16 Removing slimline ODD out of 5.25-inch ODD/HDD bracket 7.16.1 Required tools ● Preliminary and concluding steps: tool-less ● Removing a slimline ODD – EMEA: Torx Plus Size 6 – Japan: Philips (+) No.00 screw driver 7.16.2 Preliminary steps Before removing a slimline ODD, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59.
HDDs and accessible drives 7.16.3 Removing a slimline ODD out of 5.25-inch ODD/HDD bracket / 0 Figure 63: Disconnecting cables of the slimline ODD in 5.25-inch ODD/HDD bracket Ê Disconnect cables to the slimline ODD. 1 Power cable connector P4 (see "Power cable T26139-Y4012-V211" on page 239) 2 SATA cable T26139-Y4028-V201 Ê Close the front cage as described in section "Closing the front cage" on page 53.
HDDs and accessible drives / 0 Figure 64: Removing the 5.25-inch ODD/HDD bracket with the slimline ODD Ê Push the green handle backward (1) and pull the 5.25-inch ODD/HDD bracket out of its bay (2). V CAUTION! Always replace dummy modules into unused drive bays to comply with applicable EMC regulations and satisfy cooling requirements.
HDDs and accessible drives Figure 65: Removing the screws Ê Remove the three screws. Figure 66: Removing the ODD out of the 5.25-inch ODD/HDD bracket Ê Remove the ODD from its installation bay.
HDDs and accessible drives Figure 67: Removing the fixation plate of the 5.25-inch ODD/HDD bracket Ê Remove the fixation plate from the 5.25-inch ODD/HDD bracket. 7.16.4 Concluding steps Perform the following procedures to complete the task: Ê Install the 5.25-inch dummy cover as described in section "Installing 5.25inch dummy cover" on page 110. Ê Follow all procedures described in section "Closing the server" on page 54.
HDDs and accessible drives 7.17 Installing backup drive in 5.25-inch chassis bay Upgrade and Repair Units (URU) Average task duration: 10 minutes 7.17.1 Required tools ● Preliminary and concluding steps: tool-less ● Removing accessible drives: tool-less 7.17.2 Preliminary steps Before installing an accessible drive, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59.
HDDs and accessible drives 7.17.3 Installing a backup drive in 5.25-inch chassis bay Figure 68: Connecting the fixation plate to the 5.25-inch chassis bay Ê Align the four pins of the fixation plate with the screw holes on the 5.25-inch chassis bay. Figure 69: Installing the backup drive Ê Push the backup drive in its bay until it snaps into place. Ê Open the front cage as described in section "Opening the front cage" on page 52.
HDDs and accessible drives 0 / Figure 70: Connecting cables to the backup drive Ê Connect cables to the backup drive. 1 Connect the power connector P2 (see "Power cable T26139-Y4012V211" on page 239) to the power adapter cable SNP:A3C40057660 and then connect the adapter cable to the backup drive. 2 USB cable T26139-Y3973-V401. Ê Connect the USB cable to the system board connector USB-FRONT3/4. 7.17.
HDDs and accessible drives 7.18 Removing backup drive out of 5.25-inch chassis bay 7.18.1 Required tools ● Preliminary and concluding steps: tool-less ● Removing a backup drive: tool-less 7.18.2 Preliminary steps Before removing a backup drive, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59.
HDDs and accessible drives 7.18.3 Removing backup drive out of 5.25-inch chassis bay 0 / Figure 71: Disconnecting cables from the backup drive Ê Disconnect all cables from the backup drive. Ê Disconnect cables from the backup drive. 1 Disconnect the adapter cable from the backup drive and then disconnect the power connector P2 (see "Power cable T26139Y4012-V211" on page 239) from the power adapter cable SNP:A3C40057660. 2 USB cable T26139-Y3973-V401.
HDDs and accessible drives 0 / Figure 72: Removing the backup drive Ê Push the green handle backward (1) and pull the backup drive out of its bay (2). V CAUTION! Always replace dummy modules into unused drive bays to comply with applicable EMC regulations and satisfy cooling requirements. 7.18.4 Concluding steps Perform the following procedures to complete the task: Ê Install the 5.25-inch dummy cover as described in section "Installing 5.25inch dummy cover" on page 110.
HDDs and accessible drives 7.19 Installing slimline ODD in slimline chassis bay Upgrade and Repair Units (URU) Average task duration: 10 minutes 7.19.1 Required tools ● Preliminary and concluding steps: – Slotted screw driver (only for removing the ODD filler cover) ● Installing accessible drives: tool-less 7.19.
HDDs and accessible drives 7.19.3 Removing the ODD filler cover Figure 73: Removing the ODD filler cover Ê Using a slotted screw driver, pry the ODD filler cover out of its bay and remove it from its installation bay. V CAUTION! The ODD filler cover is not for future use. You cannot install the ODD filler cover again. Do not pry out the ODD filler cover, if you do not install a slimline ODD.
HDDs and accessible drives 7.19.4 Installing the ODD Figure 74: Installing the ODD Ê Attach the installation bracket to the ODD as shown.
HDDs and accessible drives Figure 75: Installing the ODD Ê Ensure that the hooks on the installation bracket properly engage with the screw holes on the ODD (see circles). Figure 76: Installing the ODD Ê Insert the ODD in the bay until it snaps into place.
HDDs and accessible drives Ê Open the front cage as described in section "Opening the front cage" on page 52. / 0 Figure 77: Connecting cables to the ODD Ê Connect cables to the ODD.
HDDs and accessible drives Figure 78: Removing the ODD cover Ê Press the ODD cover out from inside to outside of the server cover. Ê Remove the ODD cover 7.19.5 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page 53. Ê Follow all procedures described in section "Closing the server" on page 54.
HDDs and accessible drives 7.20 Replacing slimline ODD out of slimline chassis bay 7.20.1 Required tools ● Preliminary and concluding steps: ● Removing accessible drives: tool-less 7.20.2 Preliminary steps Before replacing an accessible drive, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59.
HDDs and accessible drives 7.20.3 Replacing a slimline ODD out of slimline chassis bay / 0 Figure 79: Disconnecting cables from the ODD Ê Disconnect all cables from the ODD. 1 Power cable connector P4 (see "Power cable T26139-Y4012-V211" on page 239) 2 SATA cable T26139-Y4028-V102 Ê Close the front cage as described in "Closing the front cage" on page 53.
HDDs and accessible drives / 0 Figure 80: Removing the ODD Ê Press the green locking (1) and pull the ODD out of its bay (2). Ê Install a new ODD in this bay. 7.20.4 Concluding steps Perform the following procedures to complete the task: Ê Follow all procedures described in section "Closing the server" on page 54. Ê If BitLocker functionality is used and has been disabled before starting the maintenance task, re-enable BitLocker as described in section "Enabling BitLocker functionality" on page 66.
8 System fan Basic information The PRIMERGY MX130 S2 server features one system fan module. I Additional fans in PSU and processor heat sink cannot be replaced individually. V CAUTION! Since the system fan is not redundant is has to be replaced immediately in case of defects or pre-failure events. Safety notes V CAUTION! ● Do not damage or modify internal cables or devices. Doing so may cause a device failure, fire, or electric shock.
System fan 8.1 Replacing the system fan module Upgrade and Repair Units (URU) Average task duration: 5 minutes 8.1.1 Required tools ● Preliminary and concluding steps: tool-less ● Replacing the fan module: – Side cutter / pincer 8.1.2 Preliminary steps Before replacing the fan module, perform the following steps: Ê Follow all procedures described in section "Opening the server" on page 48. Ê Open the front cage as described in section "Opening the front cage" on page 52.
System fan 8.1.3 Removing the system fan module Figure 81: Disconnecting the cable of the system fan module Ê Disconnect the fan cable from system board connector FAN2.
System fan Figure 82: Cutting the front fan rivets Ê Tear the front fan rivets a little out and cut them with a side cutter.
System fan Figure 83: Removing the system fan module Ê Pull the fan cable out of the chassis. Ê Take the system fan module out from the chassis.
System fan 8.1.4 Installing the system fan module Figure 84: Fitting the new system fan module with new front fan rivets Ê Fit four new front fan rivets into the fan.
System fan D C B A Figure 85: System fan with installed fan rivets Ê The front system fan has four fan rivets A, B, C and D (see circles).
System fan Figure 86: Installing the system fan module Ê Insert the system fan module into the chassis. A B B Figure 87: Fitting front fan rivets Ê Put the two front fan rivets A and B into the fan slots in the chassis with the help of a pincer (see circles).
System fan A B Figure 88: Position of front fan rivets A and B Ê Make sure that both front fan rivets A and B fit the holes in the chassis fan slots (see circles). B D A C Figure 89: Position of all front fan rivets Ê The two front fan rivets C and D also must fit the holes in the chassis fan slots (see circles). I Note that front fan rivet D is hidden (see orange circle).
System fan C Figure 90: Fitting front fan rivet C Ê Use a pincer to fit front fan rivet C in the hole in the chassis fan slot (see circle). D Figure 91: Fitting front fan rivet D Ê Use a pincer to fit front fan rivet D in the hole in the chassis fan slot (see circle).
System fan Figure 92: Position of the front fan rivets in the chassis fan slots Ê Make sure that all front fan rivets match the holes in the chassis fan slots (see circles). Figure 93: Initial position of a front fan rivet in the chassis fan slot First, the front fan rivets are sticking out of the chassis fan slots marginally.
System fan Figure 94: Final position of a front fan rivet in the chassis fan slot Ê Tear out the front fan rivets a little bit. / 0 / 0 Figure 95: Cutting the overlaying part of the front fan rivets Ê Cut the overlaying part of the front fan rivets (1) with the side cutter (2). Ê Install the fan cable.
System fan Figure 96: Connecting the system fan cable Ê Connect the fan cable to system board connector FAN2. 8.1.5 Concluding steps Ê Follow all procedures described in section "Closing the server" on page 54.
System fan 158 Upgrade and Maintenance Manual MX130 S2
9 Expansion cards This chapter provides information on how to install, remove or replace expansion cards. Safety notes V CAUTION! ● Do not damage or modify internal cables or devices. Doing so may cause a device failure, fire, or electric shock. ● Devices and components inside the server remain hot after shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.
Expansion cards 9.
Expansion cards 9.2 Expansion cards 9.2.1 Installing expansion cards Upgrade and Repair Units (URU) Average hardware task duration: 5 minutes Average software task duration: 5 minutes 9.2.1.1 Required tools ● Preliminary and concluding steps: tool-less ● Installing expansion cards: tool-less 9.2.1.2 Preliminary steps Before installing an expansion card, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59.
Expansion cards 9.2.1.3 Removing a PCI slot bracket Figure 98: Opening the PCI slot bracket clamp Ê Fold up the slot bracket clamp.
Expansion cards Figure 99: Removing the PCI slot bracket Ê Remove the slot bracket. V CAUTION! Keep the slot bracket for further use. Always replace slot brackets into unused PCI slot openings to comply with applicable EMC regulations and satisfy cooling requirements. 9.2.1.4 Installing an expansion card Ê Remove the expansion card from its protective packaging. I For further instructions regarding controller settings, please refer to the accompanying documentation.
Expansion cards Figure 100: Installing the expansion card Ê Carefully insert the expansion card into the desired PCI slot and press down firmly until it is fully seated in the slot. Ê Fold down slot bracket clamp until it locks in place.
Expansion cards 9.2.1.5 Connecting cables to the expansion card Ê If applicable, connect internal cables to the expansion card. I For a complete cabling overview, please refer to section "Cabling" on page 235. 9.2.1.6 Concluding steps Perform the following procedures to complete the task: Ê Follow all procedures described in section "Closing the server" on page 54.
Expansion cards 9.2.2.2 Preliminary steps Before removing an expansion card, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59. Ê Follow all procedures described in section "Opening the server" on page 48. 9.2.2.3 Removing an expansion card Figure 101: Removing an expansion card Ê If necessary, disconnect all cables from the expansion card. Ê Fold up the locking handle on the slot bracket clamp.
Expansion cards 9.2.2.4 Installing a PCI slot bracket V CAUTION! Always replace slot brackets into unused PCI slot openings to comply with applicable EMC regulations and satisfy cooling requirements. Figure 102: Installing a PCI slot bracket Ê Insert a PCI slot bracket into the unused PCI slot opening. Ê Fold down slot bracket clamp until it locks in place. 9.2.2.
Expansion cards 9.2.3 Installing eSATA cable Upgrade and Repair Units (URU) Average hardware task duration: 5 minutes 9.2.3.1 Required tools ● Preliminary and concluding steps: tool-less ● Installing expansion cards: tool-less 9.2.3.2 Preliminary steps Before installing an expansion cable, perform the following steps: Ê Follow all procedures described in section "Opening the server" on page 48. Ê Remove a PCI slot bracket as described in section "Removing a PCI slot bracket" on page 162. 9.2.3.
Expansion cards Figure 103: Installing the eSATA cable Ê Carefully insert the eSATA cable into the desired PCI slot and press down firmly until it is fully seated in the slot. Ê Fold down slot bracket clamp until it locks in place.
Expansion cards 9.2.3.4 Connecting cable of the eSATA cable to connector Figure 104: Connecting the eSATA cable Ê Connect the end of eSATA cable to the system board connector SATA6. Ê Fold the cable carefully as shown in the picture. 9.2.3.5 Concluding steps Perform the following procedures to complete the task: Ê Follow all procedures described in section "Closing the server" on page 54. 9.2.
Expansion cards 9.2.4.1 Required tools ● Preliminary and concluding steps: tool-less ● Removing expansion cards: tool-less 9.2.4.2 Preliminary steps Before removing an eSATA cable, perform the following steps: Ê Follow all procedures described in section "Opening the server" on page 48. 9.2.4.3 Disconnecting eSATA cable (optional for specific markets) Figure 105: Disconnecting the eSATA cable Ê Disconnect the end of eSATA cable from the system board connector SATA6.
Expansion cards 9.2.4.4 Removing an eSATA cable Figure 106: Removing an eSATA cable Ê Fold up the locking handle on the slot bracket clamp. Ê Carefully remove the eSATA cable from its slot. 9.2.4.5 Concluding steps Perform the following procedures to complete the task: Ê Install a PCI slot bracket as described in section "Installing a PCI slot bracket" on page 167. Ê Follow all procedures described in section "Closing the server" on page 54.
Expansion cards 9.3 Additional tasks This section provides additional expansion card related information on how to install slot brackets. 9.3.1 Mounting expansion card slot brackets Customer Replaceable Units (CRU) Average task duration: 5 minutes This section provides general instructions on mounting slot brackets as well as specific instructions for the following network adapters: ● "Network adapter D2907" on page 174 ● "Network adapter D2745" on page 176 9.3.1.
Expansion cards 9.3.1.2 Network adapter D2907 0 / Figure 107: Network adapter D2907 - Mounting the slot bracket (A) Ê Place the controller on the mounting tabs on the slot bracket (1). Ê Carefully shift the slot bracket towards the controller (2) until the plug shells engage with the cut-outs in the slot bracket connector panel.
Expansion cards Figure 108: Network adapter D2907 - Mounting the slot bracket (B) Ê Secure the slot bracket to the controller with two M3 x 4.5 mm screws. Figure 109: Network adapter D2907 - Mounting the slot bracket (C) I Assembled network adapter D2907.
Expansion cards 9.3.1.3 Network adapter D2745 Figure 110: Network adapter D2745 - Mounting the slot bracket (A) Ê Hinge the slot bracket to the plug shell as shown (1). Ê Fold the slot bracket towards the controller until the threaded mounting tab is aligned with the screw hole on the controller (2).
Expansion cards Figure 111: Network adapter D2745 - Mounting the slot bracket (B) Ê Secure the slot bracket to the controller with one M3 x 4.5 mm screw.
Expansion cards 178 Upgrade and Maintenance Manual MX130 S2
10 Main memory Safety notes V CAUTION! ● Do not install unsupported third party memory modules. For further information on supported memory modules, refer to section "Basic procedure" on page 180. ● Memory modules remain hot after shutdown. Wait for components to cool down before installing or removing memory modules to prevent burns. ● Do not insert and remove memory modules repeatedly. Doing so may cause failures.
Main memory 10.1 Basic procedure – The system board is equipped with four memory connectors. – The system has to be equipped with at least one memory module. Populate memory slot 1 first. – Supported memory modules: DDR3-1066 PC3-8500, DDR3-1333 PC3-10600 or DDR3-1600 PC312800U unbuffered single rank (SR) or dual rank (DR) UDIMM memory modules with or without ECC – Supported capacities: 1 GB, 2 GB or 4 GB – Maximum amount of RAM: 16 GB 10.1.1 Memory sequence – Populate memory slot 1 first.
Main memory Number of memory modules inserted Slots to be used 1 2 3 4 Slot 1, Channel A o o o o o o o o o Slot 2, Channel B Slot 3, Channel A Slot 4, Channel B o Table 5: Mounting order 10.1.2 Operation modes – The maximum performance can be achieved in a symmetric dual-channel configuration. Therefore both channels have to be populated with the same amount of memory. The DRAM device technology (1 Gbit / 2 Gbit / 4 Gbit) may vary from one channel to the other.
Main memory 10.2 Installing memory modules Upgrade and Repair Units (URU) Average task duration: 5 minutes 10.2.1 Required tools ● Preliminary and concluding steps: tool-less ● Installing memory modules: tool-less 10.2.2 Preliminary steps Before installing a memory module, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59. Ê Follow all procedures described in section "Opening the server" on page 48. 10.2.
Main memory Figure 115: Installing memory modules (B) Ê Align the notch on the bottom of the module with the crossbar in the connector. Ê Press down on the memory module until the securing clips snap into the cutouts at each end of the module. 10.2.4 Concluding steps Perform the following procedures to complete the task: Ê Follow all procedures described in section "Closing the server" on page 54.
Main memory 10.3 Removing memory modules Upgrade and Repair Units (URU) Average task duration: 5 minutes 10.3.1 Required tools ● Preliminary and concluding steps: tool-less ● Removing memory modules: tool-less 10.3.2 Preliminary steps Before removing a memory module, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59. Ê Follow all procedures described in section "Opening the server" on page 48. 10.3.
Main memory Figure 116: Removing memory modules Ê Eject the desired memory module by pressing out the securing clips at each end of the memory module connector. Ê Remove the ejected memory module. 10.3.4 Concluding steps Perform the following procedures to complete the task: Ê Follow all procedures described in section "Closing the server" on page 54. Ê If available, update the system board BIOS to the latest version as described in section "Updating the system board BIOS" on page 62.
Main memory 186 Upgrade and Maintenance Manual MX130 S2
11 Processors Safety notes V CAUTION! ● Do not install unsupported processors. For further information on supported processors, refer to section "Basic procedure" on page 188. ● Circuit boards and soldered parts of internal options are exposed and can be damaged by static electricity. Always discharge static build-up (e.g. by touching a grounded object) before handling electrostaticsensitive devices (ESDs) ● Do not touch the circuitry on boards or soldered parts.
Processors 11.1 Basic procedure Supported processors – AMD FX, AMD Sempron, Athlon II, Phenom II – Socket type: AM3+ – Thermal Design Power (TDP) class: 95W 11.2 Replacing the processor heat sink Field Replaceable Units (FRU) Average task duration: 15 minutes 11.2.1 Required tools ● Preliminary and concluding steps: tool-less ● Removing and installing the processor heat sink: – Phillips PH2 / (+) No. 2 screw driver 11.2.
Processors 11.2.3 Removing the processor heat sink Figure 117: Removing the processor heat sink Ê Loosen the four captive screws on the heat sink in a crossover pattern. Ê Disconnect the CPU fan cable from the system board connector FAN1. Ê Carefully turn the heat sink back and forth to detach it from the processor. I This may be necessary due to the adhesive quality of the thermal paste located between the heat sink and processor. Ê Lift the heat sink out of the chassis.
Processors 11.2.4 Thermal paste I On a new CPU heat sink a thin layer of thermal compound has already been pre-applied to its lower surface. This layer of thermal compound is protected by a cover. Ê Remove the cover at the lower surface of the new heat sink. 11.2.5 Installing the processor heat sink Figure 118: Installing the heat sink Ê Carefully seat the heat sink on the four threaded holes as shown. V CAUTION! – The printed arrow on the heat sink must point to the rear side of the chassis.
Processors Ê Fasten the four captive screws on the heat sink (screw torque: 0.6 Nm, not applicable for the Japanese market). Ê Connect the CPU fan cable to the system board connector FAN1. 11.2.6 Concluding steps Perform the following procedures to complete the task: Ê Follow all procedures described in section "Closing the server" on page 54. 11.
Processors 11.3.2 Preliminary steps Before upgrading or replacing the processor, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality" on page 59. Ê Follow all procedures described in section "Opening the server" on page 48. 11.3.3 Removing the processor heat sink Refer to section "Removing the processor heat sink" on page 189 for removing the processor heat sink. 11.3.
Processors Figure 120: Removing the processor Ê Carefully remove the defective processor from its socket in a vertical motion.
Processors 11.3.5 Installing the processor Figure 121: Installing the processor Ê Hold the processor with your thumb and index finger. Make sure that the indication triangle on the processor aligns with the notch on the socket. Ê Lower the processor straight down without tilting or sliding it in the socket. V CAUTION! – Ensure that the processor is level in the socket. – Be careful not to touch or bend the pins on the processor. – Never touch the underside of the processor.
Processors Figure 122: Latching the socket lever Ê Latch the socket lever.
Processors 11.3.6 Applying thermal paste I For the Japanese market, follow the instructions provided separately. I If the processor upgrade or replacement kit contains a new CPU heat sink, a thin layer of thermal compound has already been pre-applied to its lower surface. This layer of thermal compound is protected by a cover.In this case, please proceed with section "Installing the processor heat sink" on page 197.
Processors Figure 124: Applying thermal paste Ê Apply a small streak of thermal paste (1.0 gram, see description above) to the center of the processor surface as shown. V CAUTION! Do not mix different types of thermal paste. 11.3.7 Installing the processor heat sink Refer to section "Installing the processor heat sink" on page 190 for installing the processor heat sink. 11.3.
Processors 198 Upgrade and Maintenance Manual MX130 S2
12 System board and components This chapter provides information on how to replace the system board and system board components as its CMOS battery and the Trusted Platform Module (TPM). Safety notes V CAUTION! ● Devices and components inside the server remain hot after shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.
System board and components 12.1 Replacing the CMOS battery Upgrade and Repair Units (URU) Average task duration: 5 minutes CMOS memory (volatile BIOS memory) and the real-time clock are powered by a lithium coin cell (CMOS battery). This cell lasts two to ten years, depending on ambient temperature and use. If the CMOS battery is depleted or falls below minimum voltage levels, it need to be replaced immediately.
System board and components 12.1.2 Preliminary steps Before replacing the CMOS battery, perform the following steps: Ê Follow all procedures described in section "Opening the server" on page 48. 12.1.3 Removing the CMOS battery Figure 125: Removing the CMOS battery Ê Press out on the locking spring to eject the depleted CMOS battery (1).
System board and components Ê Carefully pry the depleted CMOS battery out of its socket. Ê Remove the CMOS battery (2). I Do not throw the CMOS battery into the trash can. Lithium batteries must be disposed of in accordance with local regulations concerning special waste. 12.1.4 Installing the CMOS battery Figure 126: Installing the CMOS battery Ê At a slight angle, fit the new CMOS battery into its socket as shown (1).
System board and components This information does not apply to the Japanese market. Do not throw lithium batteries into the trash can. They must be disposed of in accordance with local regulations concerning special waste. Make sure that you insert the battery the right way round. The plus pole must be on the top! Ê Push down the CMOS battery (2) until it locks in place. Ê Ensure that the locking spring is properly engaged. 12.1.
System board and components 12.2 Trusted Platform Module (TPM) This section provides information on how to install, remove or replace the Trusted Platform Module (TPM). 12.2.1 Installing the TPM board Field Replaceable Units (FRU) Average hardware task duration: 5 minutes 12.2.1.1 Required tools ● Preliminary and concluding steps: – Phillips PH2 / (+) No.
System board and components 12.2.1.3 Installing the TPM board Figure 127: TPM kit TPM kit (S26361-F3299-E2): 1 TPM module S26361-D2727-A10 2 TPM spacers I Use the white TPM spacer (A3C40106008). The black TPM spacer is not used in this server.
System board and components / 0 Figure 128: TPM mounting location (detail) TPM mounting location on the system board: 1 2 Cut-out for TPM spacer TPM connector Figure 129: Installing the TPM spacer Ê Snap the TPM spacer into the cut-out in the system board.
System board and components Figure 130: Installing the TPM board Ê Connect the new TPM board to the system board. Figure 131: TPM bit insert Ê Attach the TPM bit insert or TPM module fixing tool (Japanese market) to a bit screw driver.
System board and components Figure 132: Securing the TPM board Ê Secure the TPM board with the TPM special screw using the TPM bit insert. I Do not fasten the screw too firmly. Stop as soon as the head of the screw lightly touches the TPM board. 12.2.1.4 Concluding steps Perform the following procedures to complete the task: Ê Follow all procedures described in section "Closing the server" on page 54. Ê Enable TPM in the system board BIOS. Proceed as follows: Ê Switch on or restart your server.
System board and components I For detailed information on how to access the BIOS and modify settings, refer to the "Description - BIOS Manual D3090 / D3091" available online at http://manuals.ts.fujitsu.com or from the ServerView Suite DVD 2 supplied with your PRIMERGY server. Ê If BitLocker functionality is used and has been disabled before starting the maintenance task, re-enable BitLocker as described in section "Enabling BitLocker functionality" on page 66. 12.2.
System board and components 12.2.2.2 Preliminary steps Before removing the TPM board, perform the following steps: Ê Before removing the TPM board, it is necessary to remove BitLockerprotection from the computer and to decrypt the volume.
System board and components Ê Follow all procedures described in section "Opening the server" on page 48. 12.2.2.3 Removing the TPM board Ê Remove the system board as described in section "Removing the system board" on page 215. Ê Lay the system board on a soft, antistatic surface with its component side facing down. Figure 133: Removing the TPM screw Ê Locate the slotted lower end of the TPM screw (1).
System board and components Ê Carefully loosen the TPM screw using a thin slotted screw driver (e.g. watchmaker's screw driver) or the dedicated TPM screw driver (Japanese market) (2). V CAUTION! Ensure to turn the screw in the direction of the arrow in order to remove it! Slowly and carefully increase the pressure on the screw until it begins to turn. The effort when loosing the screw should be as low as possible. Otherwise the thin metal bar may break, rendering it impossible to loosen the screw.
System board and components 12.3 Replacing the system board Field Replaceable Units (FRU) Average hardware task duration: 50 minutes Average software task duration: 10 minutes 12.3.1 Required tools Note on TPM I The system board can be equipped with an optional TPM (Trusted Platform Module). This module enables third party programs to store key information (e. g. drive encryption using Windows Bitlocker Drive Encryption).
System board and components Replacing the system board: ● – Phillips PH2 / (+) No. 2 screw driver ● Replacing the system board: – Magnifying glass (for inspecting socket cover springs) If a TPM module is installed: – Bit screw driver – TPM bit insert* – thin slotted screw driver (2 x 0.4 mm)* *For the Japanese market: – Dedicated TPM screw driver (CWZ8291A) – TPM module fixing tool (S26361-F3552-L909) 12.3.
System board and components 12.3.3 Removing the system board Ê Remove all cables from the system board. Ê Remove the following components from the system board as shown in the related sections: – Memory modules: refer to section "Removing memory modules" on page 184 I Ensure to take note of the memory modules’ mounting positions for reassembly.
System board and components Ê Remove eight screws from the system board (see circles) beginning with the two centering bolts (C). Figure 136: Detaching the system board (B) V CAUTION! – Do not lift or handle the system board by any of its heat sinks! – Ensure not to damage the EMI springs to comply with applicable EMC regulations and satisfy cooling requirements and fire protection measures.
System board and components Figure 137: Removing the heat sink counter plate Ê Remove heat sink counter plate from the bottom side of the system board.
System board and components 12.3.4 Installing the system board 12.3.4.1 Mounting the system board Figure 138: Inserting the heat sink counter plate Ê Insert the heat sink counter plate from the bottom to the system board. The bolts must come through the system board (see circles). Ê Install the processor and the heat sink as described in section "Replacing the processor" on page 191.
System board and components Figure 139: Installing the system board (A) Ê Hold the new system board by the memory module ejectors and a PCI slot. V CAUTION! – Do not lift or handle the system board by any of its heat sinks! – Ensure not to damage the EMI springs to comply with applicable EMC regulations and satisfy cooling requirements and fire protection measures. – Ensure that the system board is not scratched by the metal stop angle (see circle).
System board and components C C C C Figure 140: Installing the system board (B) Ê Secure the system board with eight screws (M3 x 4.5 mm, standard C67 screw) (see circles) beginning with the two centering bolts (C). I Screw torque: 0.6 Nm (not applicable for the Japanese market) Ê Verify the settings on the new system board (DIP switches, jumpers). For a detailed description, please refer to section "Onboard settings" on page 250.
System board and components 12.3.5 Concluding steps Ê Reconnect all cables to the system board. For a complete cabling overview, please refer to section "Cabling" on page 235. Ê Reinstall all remaining system board components as shown in the related sections: – Memory modules: refer to section "Installing a memory module" on page 182 I Install all memory modules into their original slots.
System board and components 222 Upgrade and Maintenance Manual MX130 S2
13 Front panel and front USB Safety notes V CAUTION! ● When inserting the front panel module into the server, ensure not to pinch or strain any connected cables. ● Circuit boards and soldered parts of internal options are exposed and can be damaged by static electricity. Always discharge static build-up (e.g. by touching a grounded object) before handling electrostaticsensitive devices (ESDs) ● Do not touch the circuitry on boards or soldered parts.
Front panel and front USB 13.1 Replacing the front panel indicators The On/Off button and the HDD activity LED are part of the front panel module. Field Replaceable Units (FRU) Average task duration: 15 minutes 13.1.1 Required tools ● Preliminary and concluding steps: tool-less ● Replacing the front panel module: tool-less 13.1.2 Preliminary steps Ê Follow all procedures described in section "Opening the server" on page 48.
Front panel and front USB 13.1.3 Removing the On/Off button Figure 141: Removing the On/Off button Ê Press the two retaining clips together and push the On/Off button backwards in the chassis. I Note the orientation of the On/Off button. If it is installed in the other direction, it does not work properly.
Front panel and front USB 13.1.4 Removing the HDD activity LED / 0 / Figure 142: Removing the HDD activity LED Ê Push apart the two latches (1) and pull the LED to the direction of the arrow (2).
Front panel and front USB 13.1.5 Removing the cable for On/Off button and HDD activity LED / 0 Figure 143: Disconnecting front panel cable Ê Remove the cable from the cable holder(1). Ê Disconnect the cable from system board connector Front panel (2).
Front panel and front USB 13.1.6 Installing the On/Off button and the HDD activity LED / 0 2 1 Figure 144: Installing the On/Off button and HDD activity LED Ê Insert the HDD activity LED in the direction shown until it snaps in place (1). Ê Insert the On/Off button in the direction shown until it snaps in place (2). I Take care of the orientation of the On/Off button. If it is installed in the other direction, it does not work properly.
Front panel and front USB 13.2 Replacing the front USB board Field Replaceable Units (FRU) Average task duration: 15 minutes 13.2.1 Required tools ● Preliminary and concluding steps: tool-less ● Replacing the front panel module: – Phillips PH2 / (+) No. 2 screw driver 13.2.2 Preliminary steps Ê Follow all procedures described in section "Opening the server" on page 48. Ê Open the front cage as described in section "Opening the front cage" on page 52.
Front panel and front USB 13.2.3 Removing the defective front USB board 0 1 0 / Figure 145: Disconnecting the USB front cable, removing the front USB board Ê Disconnect the front USB cable from the front USB board (1). Ê Remove the two screws of the front USB board (2). Ê Remove the front USB board (3).
Front panel and front USB 13.2.4 Installing the new front USB board Figure 146: Installing the front USB board Ê Insert the new front USB board.
Front panel and front USB / / 0 Figure 147: Connecting the USB front cable Ê Secure the new front USB board with two screws (1) Ê Connect the front USB cable to the front USB board (2). 13.2.5 Concluding steps Ê Close the front cage as described in section "Closing the front cage" on page 53. Ê Follow all procedures described in section "Closing the server" on page 54.
14 Cables Safety notes V CAUTION! ● Always hold cables by their connectors when disconnecting them. Never pull on the cable to disconnect cables. ● Ensure that none of the cables are scraped, strained or otherwise damaged while replacing system components. ● Immediately replace cables with damaged shielding. ● Always use shielded network cables.
Cables 14.1 Cabling overview 14.1.
Cables 14.2 Cabling 14.2.
Cables Configuration with RDX PSU P4 slim ODD Module 2 Channel B PS2 Module 4 Channel B USB 11+12 SATA Power Module 1 Channel A P3 Module 3 Channel A Frontpanel P1 Power Supply HDD3 (3,5") P2 COM DVI-I SNP:A3C40057660 RDX-Drive AM3/AM3+ CPU FAN1 USB 9+10 Audio Super I/O optional) (optional) TPM FAN2 LAN/ USB 7+8 P5 HDD2 (3,5") PCI-Ex1 SATA 5+6 Northbridge Battery PCI-E x4 P6 SATA 3+4 PCI-E x16 HDD1 (3,5")1 Southbridge PCI Intrusion USB 5+6 / Dash USB 3+4 USB 1+2 SATA 1+2
Cables 14.2.
Cables Data cabling variable positions depending on the drive configuration Module 2 Channel B PS2 Module 4 Channel B USB 11+12 SATA Power Module 1 Channel A Frontpanel Module 3 Channel A Power Supply COM DVI-I AM3/AM3+ CPU LAN/ USB 7+8 o optional) Super I/O (optional) Audio TPM FAN2 FAN1 USB 9+10 PCI-Ex1 SATA 5+6 Northbridge Battery PCI-E x4 SATA 3+4 PCI-E x16 Southbridge PCI Intrusion USB 5+6 / Dash USB 3+4 USB 1+2 SATA 1+2 Buzzer (optional) Figure 151: Data cabl
Cables 14.3 Replacing the power cable Field Replaceable Units (FRU) Average task duration: 10 minutes P2 P1 P4 P3 P5 P6 Figure 152: Power cable T26139-Y4012-V211 14.3.1 Required tools ● Preliminary and concluding steps: tool-less ● Replacing the power cable: tool-less 14.3.2 Preliminary steps Before replacing the power cable, perform the following steps: Ê Follow all procedures described in section "Opening the server" on page 48.
Cables 14.3.3 Removing the power cable 0 / Figure 153: Detaching the power cable Ê While pressing the release latch on the connector (1), disconnect the power cable from the POWER SATA connector on the system board (2). Ê Remove the power cable T26139-Y4012-V211 from the five cable clamps (see circles).
Cables / 0 Figure 154: Disconnecting the power cable from installed drives Ê Disconnect all power cable connectors from the installed drives (1). It depends on your configuration which drives are installed. For details refer to section "HDDs and accessible drives" on page 79. Ê Disconnect the power cable connectors P5 and P6 from the installed HDDs (2). For details refer to "Replacing the power cable" on page 239. Ê Remove the power cable from the chassis.
Cables 14.3.4 Installing the power cable / Figure 155: Connecting the power cable to the system board Ê Connect the new power cable to system board connector POWER SATA (1). Ê Run the power cable through the five cable clamps (see circles).
Cables / 0 Figure 156: Connecting the power cable Ê Connect all power cable connectors to the installed drives (1). It depends on your configuration which drives are installed. For details refer to section "HDDs and accessible drives" on page 79. Ê Connect the power cable connectors P5 and P6 to the installed HDDs (2). For details refer to section "HDDs and accessible drives" on page 79 and "Power cabling" on page 235. 14.3.
Cables 244 Upgrade and Maintenance Manual MX130 S2
15 Appendix 15.1 Mechanical overview 15.1.1 Server front / 3 3 0 2 1 Figure 157: PRIMERGY MX130 S2 front Pos. Component 1 5.
Appendix 15.1.2 Server rear / 0 1 2 7 64 5 4 4 3 Figure 158: PRIMERGY MX130 S2 rear Pos.
Appendix 15.1.3 Server interior 0 1 3 : 2 9 / 7 4 6 8 5 Figure 159: PRIMERGY MX130 S2 interior Pos.
Appendix 15.2 Configuration tables 15.2.1 Mounting order for HDDs Please refer to chapter "HDDs and accessible drives" on page 79. 15.2.2 Memory board configuration Please refer to chapter "Main memory" on page 179. 15.2.3 Expansion card configuration table Please refer to chapter "Expansion cards" on page 159.
Appendix 15.3 Connectors and indicators 15.3.1 Connectors and indicators on the system board 15.3.1.
Appendix No. Print Description 9 USB-FRONT 3/4 USB connector for accessible backup drive 10 Dash USB 5/6 USB connector for Dash LAN cable 15.3.1.2 Onboard settings Recovery Power On/Off Reset Power LED HD-LED 2 1 Figure 161: Jumper Setting Description Default Password skip disabled and recovery BIOS disabled. RCV Recovery BIOS enabled. When the recovery BIOS is applied on a system board, the password set by customers disappears from system board. SKP Password skip enabled.
Appendix 15.3.1.
Appendix 15.3.1.
Appendix 15.3.2 Connectors and indicators on the front panel 1 1 0 / Figure 164: Front side (indicators and controls) 1 HDD activity indicator 3 2 USB connectors 2 On/Off button - Power-on indicator Status indicators Pos.
Appendix Buttons Pos. Button Function This button is used to switch the server on or off. I If the system is running an ACPI-compliant 2 On / Off button operating system, the pressing the On / Off button will performs a graceful shutdown. Pressing and holding the On / Off button for five seconds will switches the server off without shutting down the operating system. 15.
Appendix Ê Follow all procedures described in section "Opening the server" on page 48. Ê Take the system down to its minimum startup configuration. Ê Connect a keyboard, mouse and display to the server. Ê Follow all procedures described in section "Closing the server" on page 54. V CAUTION! Since the system fan is not included in the minimum startup configuration, the server must be shut down immediately after the diagnostic process is complete (POST phase has been passed).
Appendix 256 Upgrade and Maintenance Manual MX130 S2
