C150-E194-01EN fi-4110CU Image Scanner Operator’s Guide
FOR SAFE OPERATION Treatment of This Manual Since this manual contains important information for using the fi-4110CU, read it thoroughly before using the product. Use the fi-4110CU only after thoroughly reading and understanding especially the section "Important Alert Messages" in this manual. Keep this manual handy, and store it carefully.
Notice to Canadian Users This digital apparatus does not exceed the class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003.
Warning: This equipment may cause electromagnetic interference. It has not been tested to show compliance with AS3548 Class A equipment, which is designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
Preface Thank you very much for your purchase of the fi-4110CU Image Scanner. The fi-4110CU Image Scanner can read very fine color images. As this manual explains the basic handling of the scanner, read it carefully to use the scanner properly. In this manual, the MicrosoftÒ Windows 98Ò Operating System is referred to as Windows 98, the MicrosoftÒ Windows MEÒ Operating System is referred to as Windows ME, and the MicrosoftÒ Windows 2000Ò Operating System is referred to as Windows 2000.
Important Notes to Users Every user is requested to use this product including the manuals and software supplied with the product at the user's own responsibility. Fujitsu assumes no liability with respect to any damage or loss caused to data as the result of using this product. Please understand that the warranty range for failure of this product will never exceed the amount of money paid by the user for the product.
Contents CHAPTER 1 Notes Concerning Use ..................................................................... 1-1 1.1 1.1.1 Outline ........................................................................................................... 1-1 fi-4110CU Image Scanner .......................................................................... 1-1 1.2 Confirming the Content of Packing Box ....................................................... 1-1 1.3 Component Names and Functions .......................
4.4 4.4.1 4.4.2 4.4.3 Consumables and Regular Replacement Components .................................. 4-6 Parts Number and Replacement Cycle of Consumables and Regular Replacement Components ............................................................. 4-6 Procedure for Replacing the Pad Unit......................................................... 4-6 Procedure for Replacing the Pick Roller Unit............................................. 4-7 CHAPTER 5 When You Suspect That a Fault Occurred...........
CHAPTER Notes Concerning Use 1 This section provides an outline of the product and explains its characteristics and components. 1.1 Outline This section provides an outline of the fi-4110CU Image Scanner and explains its characteristics. 1.1.1 fi-4110CU Image Scanner The fi-4110CU Image Scanner can read very fine color images. It can also work with attached software as follows: · Scan software enables the saving of data scanned with the scanner in TIFF format in a personal computer.
1.3 Component Names and Functions This section shows the components of the scanner and explains their functions. Front Document support Document guide Automatic document feeder Operator panel Stacker Copy density dial Function No. display panel Function button Duplex button Send to button Scan button Powe lamp Component Name 1-2 Function Document support Accommodates documents to be read by the automatic document feeder. Document guide Holds documents so that they are transported straight.
Component Name Operator panel Function Copy density dial Adjusts copy density (dark/light) in five stages. Function No. display panel Displays the Function No. or also displays the scanner read mode as follows; On: Single-side reading mode Blink: Double-sided reading mode Mark: An application is being activated When the AC adapter is connected to the scanner or the PC’s power is turned on, the initialization of scanner is executed.
Back Cover open lever カバーオープンレバー Inlet ACアダプタ用コネクタ Interface connector インタフェースコネクタ Component Name Function Cover open lever Opens and closes the automatic document feeder. Inlet Accommodates the AC adapter. Interface connector Accommodates an interface cable to be connected to a personal computer. (Type B connector) Internal Feed roller Eject roller Component Name Feed roller, eject roller, facing roller 1-4 Plasticroller roller Facing Function Sends documents.
CHAPTER 2 Installation and Connection This section explains how to install the image scanner and connect it to a personal computer. See Appendix A, “Installation Specifications,” for the external dimensions of the image scanner. 2.1 Notes concerning Installation When installing the image scanner, adhere to the following installation location and environment notes: - Fire or electric shock -- Do not alter or disassemble the scanner. High voltage components are inside.
2.2 Mounting the Document Support Follow the procedure below to mount the stacker and document support. 1) Hold the document support and insert it into the hole on the lower part of the scanner until it stops. 2) Hold the document support and insert its tabs into the counterpart holes on the scanner as shown in the figure below. u Key point When documents are actually read, the user can raise the Paper Extension of the document support and pull out the stacker according to the size of the documents.
2.3 Connection This section explains how to connect this scanner and the computer, and also how to install the driver and other software. 2.3.1 Notes concerning Connection When connecting cables, adhere to the following notes: Fire or electric shock - Do not use AC adapter other than in the package. Failure to do so could result in a fire or cause the scanner to fall.
2.3.2 Confirming the System Conditions The following environments are required for connecting this scanner to the computer to read images. System Conditions OS Windows 98 preinstall version Windows 2000 preinstall version Windows ME preinstall version Interface The computer has a built-in USB port and the computer maker certifies that the port operates correctly. u Note - If your computer is updated to Windows 98 from Windows 95 or NT, the USB port, even if provided, cannot be used. 2.3.
2.3.4 Connecting to the Computer This section explains how to connect the scanner to the computer. Connect the scanner as follows: 1) Connect the type B connector of the interface cable (accessory of this scanner) to the scanner until it clicks. 2) Connect the type A connector (opposite) of the interface cable to the USB port of the computer or a USB hub.
2.4 Setting up the Stacker and Document Support Raise the Paper Extension of the document support and pull out the stacker according to the document size as follows: 1) Hold the tab of the stacker and pull. Stacker B Tab 2) Insert a finger into the dent at the center of the stacker, then lift and pull the Stacker B.
3) When using an A4-size document, raise the Paper Extension of the document support as shown below.
CHAPTER 3 Operation Set a document on the document support and read it by automatic document feeder. This section provides notes concerning operation, and explains how to read each document. 3.1 Notes concerning Operation When operating the equipment, adhere to the following points: Fire or electrical shock - If heat, smoke, offensive odor, or noise is emitted from the equipment, turn off the power switch of the main unit and disconnect the power plug from the outlet.
Fire, electrical shock, or fault - Do not allow liquids and items such as coffee or metal clips to get into the equipment. - Do not put water on the equipment or get it wet with water. - If foreign matter such as water, metal clips, or liquid gets into the equipment, disconnect the power plug immediately from the outlet. Then, notify the sales agency (or service center). This caution is intended especially for household use including the presence of children.
3.2.1 Confirming Document Condition This section explains documents that can be read and those that are difficult to read. Readable documents Readable documents are listed below. Paper type - High-quality paper - PPC paper (paper specified by Xerox Corporation) Ream weight 45 to 90 kg/ream (52.3 to 104.7 g/m2) Size A4, A5, B5, letter size, legal size, and name card size (A8) Difficult-to-read documents Some types of Documents cannot be read well.
3.2.2 Setting Documents This section explains how to set documents. Loosening documents Before setting documents, sufficiently loosen them by the following procedure: · Remove a 4 mm thick section of pages, hold the ends of the documents with both hands, and bend the documents. · Hold the documents strongly with both hands so that both ends of the documents are slanted, and then unbend the documents so that they are inflated. · Repeat the operations described above two or three times.
Base side C Set the documents AB (R e a d side o f last page ) ABC 3.3 Scanning Documents This section explains how to scan documents. 1) Make sure that the powers of the personal computer and the scanner are ON. 2) Check the document condition. For details, see Section 3.2.1, "Confirming Document Condition." 3) Before setting documents, sufficiently loosen them. For details, see Section 3.2.2, "Setting Documents." 4) Set the documents on the document support.
5) Adjust the document guides to the document width, then straighten the documents. If the documents are placed loosely between the left and right guides, they may be read diagonally. 6) Switch the reading mode by pressing the Duplex button. This switching is available from a screen of the device driver. For details, refer to the device driver manual. When the Function No. display is ON, the single-sided reading mode is active. When the Function No. display blinks, the double-sided reading mode is active.
CHAPTER 4 Daily Maintenance This section explains how to perform paper jam handling, daily maintenance, and cleaning. u Key point Clean the automatic document feeder based on the standard cleaning procedure described in Section 4.3.2, "Cleaning the Automatic Document Feeder." 4.1 Handling a Paper Jam Be aware of high – temperature in the glass surface of Automatic Document Feeder (ADF). It could result in a burn.
4) Restore the automatic document feeder into position by pushing its center. Press the center of upper cover After restoring the automatic document feeder into position, make sure that it is closed completely. If the automatic document feeder is not properly closed, a paper jam or reading error may occur. Check that both edges are closed completely 4.2 Daily Maintenance To use the image scanner over a long period of time, you must perform some tasks daily.
4.3 Cleaning This section explains how to clean the image scanner. Fire or electrical shock - When cleaning the equipment, turn off the power, and then disconnect the interface cable and disconnect the AC adapter power plug from the outlet. 4.3.1 Cleaning the Surface of the Scanner and the Document Support This section explains how to clean the scanner surface and the document support. · Use a dry cloth or a cloth moistened with a small amount of neutral detergent or isopropyl alcohol.
Clean the automatic document feeder through the following procedure (see the figure on the next page for location): 1) Open the automatic document feeder by pulling it toward you while raising the cover open lever. 2) Clean the following components with a dry cloth or a cloth moistened with cleaner F1 or isopropyl alcohol: Pad Clean the pad downward (in arrow direction) with a cloth moistened with cleaner F1 or isopropyl alcohol. In this case, be careful not to catch the cloth in the pick arm or spring.
Pick arm Pick spring Pad Feed roller Facing roller Glass, White sheet Glass, White sheet Pick roller Round button Facing roller Eject roller Cover open lever Operator panel Parts to be Cleaned on the Automatic Document Feeder 3) Restore the automatic document feeder into position. After restoring the automatic document feeder into position, make sure that it is closed completely. If the automatic document feeder is not properly closed, a paper jam or reading error may occur.
4.4 Consumables and Regular Replacement Components Fire or electrical shock - When replacing any of the equipment's consumables , first turn off the power , then disconnect the interface cable and disconnect the AC adapter power plug from the outlet. Be aware of high – temperature in the glass surface of Automatic Document Feeder (ADF). It could result in a burn. 4.4.
Pick arm Step 1 Pad unit Pad Step 2 a b 4) When mounting a new pad unit, push the pick arm downward with one hand while mounting the pad unit with the other hand. Pad unit Pad Check that the pad unit is mounted completely. If the pad unit is not mounted correctly, a document feeding error such as a paper jam may occur. 4.4.3 Procedure for Replacing the Pick Roller Unit Replace the pick roller unit through the following procedure: 1) Remove any documents from the document support.
Paw Knob Pick Roller unit Pick Roller 5) When mounting a new pick roller unit, insert it so that the pick roller unit paw slides into the pick roller unit hole of the equipment. Push the paw and the center of the pick roller unit with your hands to completely insert the pick roller. Check that the pick roller unit is mounted completely. If the pick roller unit is mounted correctly, a document feeding error such as a paper jam may occur.
CHAPTER When you suspect that a fault occurred 5 When you suspect a fault occurred while using the image scanner, check the items listed below. Problem Power is not turned on Item to be Checked Is the AC adapter connected correctly? ¾ Reading does not start Correction Connect the AC adapter correctly. Turn off the power once by disconnecting the AC adapter. Then, turn on the power again by connecting the power cable. If the power is not turned on, notify the sales agent or the nearest service center.
Problem Paper is not being fed (stops enroute). Item to be Checked Correction Is the pick roller clean? Clean the pick roller according to Section 4.3, "Cleaning." Is the pick roller worn? Replace the pick roller unit. Is any foreign matter on the transfer path? Remove foreign matter from the transfer path (see Section 4.1, "Handling a Paper Jam"). *1 Double feeding means that two or more sheets of paper are fed together.
APPENDIX Installation Specifications A The table below lists the installation specifications of the equipment. Item External dimensions (mm) Specification Width Depth Height 308.5 154 130 Weight (kg) Input power 2.5 Voltage 100 V to 240 V Number of phases Single Frequency 50/60 Hz Power consumption Operating 30 W or less Not operating 5.
