Monitor English Operating Manual SCENICVIEW B17-3/B19-3/P19-3
Are there… ... any technical problems or other questions which you would like to be clarified? Please contact our help desk (see Warranty Booklet). The latest information on our products, tips, updates, etc., can be found on the internet under: http://www.fujitsu-siemens.
This manual was produced by Xerox Global Services Published by Fujitsu Siemens Computers GmbH Order No.
SCENICVIEW B17-3/B19-3/P19-3 LCD monitor Operating Manual august 2007 edition
VESA, DDC and DPMS are registered trademarks of Video Electronics Standards Association. Copyright © Fujitsu Siemens Computers GmbH 2007 All rights, including rights of translation, reproduction by printing, copying or similar methods, in part or in whole, are reserved. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability. Right of technical modification reserved.
Contents Introduction........................................................................................................................................... 1 Notational conventions ................................................................................................................. 2 Important notes..................................................................................................................................... 2 Safety notes...............................................
Contents A26361-K1143-Z120-1-7619, edition 3
Introduction Your new LCD (Liquid Crystal Display) monitor SCENICVIEW B17-3/B19-3/P19-3 offers numerous features and functions, for example: ● ● ● ● ● ● TFT display (Thin Film Transistor; active matrix) minimal space requirements thanks to slim casing optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour purity right into the corners) high degree of brightness and good contrast high resolution (1280 x 1024) presentation of up to 16.
SCENICVIEW B17-3/B19-3/P19-3 Notational conventions The meanings of the symbols and fonts used in this manual are as follows: ! Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data. i Supplementary information, remarks, and tips follow this symbol. ► Text which follows this symbol describes activities that must be performed in the order shown.
SCENICVIEW B17-3/B19-3/P19-3 ● To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never be blocked. ● The monitor automatically sets itself to a mains voltage in the range of 100 V to 240 V. Ensure that the local mains voltage lies within these limits. ● Ensure that the power socket on the device or the grounded mains outlet is freely accessible. ● The ON/OFF switch does not disconnect the device from the mains voltage.
SCENICVIEW B17-3/B19-3/P19-3 Power cable To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to replace the original cable set. ● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements. ● The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the outer sheath. ● For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used.
SCENICVIEW B17-3/B19-3/P19-3 FCC Class B Compliance Statement The following statement applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation. NOTE: This equipment has been tested and found to comply with the limits for a "Class B" digital device, pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian InterferenceCausing Equipment Standard ICES-003 for digital apparatus.
SCENICVIEW B17-3/B19-3/P19-3 Energy Star Guidelines The Fujitsu Siemens LCD monitor SCENICVIEW B17-3/B19-3/P19-3 is designed to conserve electricity by dropping to less than 1 W when it goes into standby, suspend and OFF mode. With this new power management the LCD monitor SCENICVIEW B17-3/B19-3/P19-3 qualifies for the U.S. Environmental Protection Agency's (EPA) Energy Star Computers award.
SCENICVIEW B17-3/B19-3/P19-3 Checking the contents of the consignment The display surface of the LCD monitor is sensitive to pressure and scratches. Always hold the device by the casing! ! ► Unpack all the individual parts. ► Check the delivery for damage incurred during transportation. ► Check whether the delivery agrees with the details in the delivery note.
SCENICVIEW B17-3/B19-3/P19-3 Installing an ergonomic video workstation 2 1 1 1= Windows Avoid direct and reflected glare. Avoid glare from electric lighting. 1= 2= Edge of desk Permissible reaching sector Position the keyboard where it is easiest to reach. 1 0° 65° 30° 60° 30° 65° 2 1= 2= Bearing surface for palms Example layout of monitor, keyboard and copy-holder of hands Reaching area for frequently used equipment Position the monitor for optimum viewing.
SCENICVIEW B17-3/B19-3/P19-3 Mounting and removing the monitor base ! The display surface is susceptible to scratching! Therefore, lay the monitor on a soft surface when mounting or removing the monitor base. Folding out monitor base When delivered the lower part of the monitor base is folded up and secured to the monitor by a collar. ! The monitor base springs up about 5 cm when the collar is released. ► Lay the monitor on its face on a soft surface (A).
SCENICVIEW B17-3/B19-3/P19-3 ► 10 Proceed according to the four steps in the illustrations to fold out the monitor base.
SCENICVIEW B17-3/B19-3/P19-3 Removing monitor base Before you can use a swivel arm or a wall bracket, you must remove the monitor base: ! The display surface is susceptible to scratching! ► Switch off the monitor and pull the power plug out of the power socket. ► Lay the monitor on its face on a soft surface. ► Remove the cover and disconnect all cables. ► Remove the four screws on the rear of the monitor.
SCENICVIEW B17-3/B19-3/P19-3 Connecting the monitor ! Please take note of the safety information in the "Important notes" chapter. CE conformance and optimum picture quality are guaranteed only if you use the data cables supplied. Do not cover the ventilation openings of the monitor. The computer power plug must be pulled out! ► 12 Be sure that the monitor and the computer are switched off.
SCENICVIEW B17-3/B19-3/P19-3 Connecting cables to the monitor The monitor ports are protected by a cover. ► Remove the cover. 1 7 7 4 6 1= 2= 3= 4= 5= 6= 7= 2 3 5 Power connector DVI-D connection socket (DIGITAL) D-SUB connection socket (ANALOG) Security slot for "Kensington Lock" AUDIO-IN connector Cover position Holes for fixing swivel arm or wall bracket The data cables supplied have two 15-pin D-SUB connectors / two 24-pin DVI connectors for connection to the monitor and to the computer.
SCENICVIEW B17-3/B19-3/P19-3 Connecting cables to the computer Information on the computer connections and interfaces is contained in the operating manual for your computer. i If your computer has two monitor ports ("onboard" screen controller and separate graphics card), the monitor port for the separate graphics card is usually active. ► Connect the data cable to the (active) monitor port on the computer and secure the plug-in connection by tightening the safety screws.
SCENICVIEW B17-3/B19-3/P19-3 Adjusting portrait format The monitor can be turned from the "wide format" (landscape mode) into the "high format" position (portrait mode). ► Grasp the monitor with both hands on the right and left edge of the casing, move it into the highest position and turn it clockwise until it is in the portrait position. i ► You must use corresponding software (pivot software) so that the screen display is also shown in the portrait mode.
SCENICVIEW B17-3/B19-3/P19-3 Switching the monitor on and off (P19-3) The main switch on the underside and the On/Off switch on the front of the monitor are used to switch it on and off. ► Switch on the monitor via the main switch (4) on the underside. 43 2 1= 2= 3= 4= 1 1 Buttons for the OSD menu (on-screen display) On/Off switch Mains power indicator Main switch 3 2 The mains power indicator (3) lights up blue when the monitor and the computer are switched on.
SCENICVIEW B17-3/B19-3/P19-3 Notes on power management If your computer is equipped with power management, the monitor can support this function fully. Here the monitor does not distinguish between the individual energy-saving modes of the computer (standby mode, suspend mode and OFF mode), as it is capable of immediately switching into the mode with the highest energy-saving effect.
SCENICVIEW B17-3/B19-3/P19-3 Changing the monitor settings When putting the monitor into operation for the first time, the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs. Choosing basic monitor settings using the supplied software If one of the operating systems Windows 95/98, Windows NT, Windows Me, Windows 2000, Windows XP or OS/2 (with Windows emulation installed) is used, the basic monitor settings can be set with the CD supplied.
SCENICVIEW B17-3/B19-3/P19-3 Locking the OSD menu The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings. ► Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor with the ON/OFF switch. A message is displayed that the action has been performed. Please proceed in the same manner to release the locked OSD menu again.
SCENICVIEW B17-3/B19-3/P19-3 The corresponding setting window (here: Image Adjust) is displayed (on the right-hand side). The first function (H-Position) is highlighted. ► If necessary, press the 6 or 5 button to mark another function. ► Press the SELECT/MENU button to select the highlighted function. ► Press the 6 or 5 button to adjust the value for the selected function. ► Press the EXIT/AUTO button to exit the function.
SCENICVIEW B17-3/B19-3/P19-3 Adjusting size and position Calling the Image adjust setting window H-Position Adjusting the horizontal position With this function you move the picture to the left or to the right. V-Position Adjusting the vertical position With this function you move the picture up or down. Clock Setting synchronisation With this function you adjust the picture width to eliminate vertical picture disturbances.
SCENICVIEW B17-3/B19-3/P19-3 Setting display of the OSD menu Calling the OSD Setup setting window Language Setting language for the OSD menu With this function you choose between English (default setting), French, German, Italian and Spanish as the language for the OSD menu. OSD H-Position Setting the horizontal position of the OSD menu With this function you move the OSD menu to the left or to the right.
SCENICVIEW B17-3/B19-3/P19-3 Displaying information Calling the Information setting window With this function the model designation, serial number, resolution, H/V frequency, input signal and polarity of the synchronisation signal are displayed. Notes on ergonomic colour adjustment If you select colours for the display in your application programmes, take note of the information below.
SCENICVIEW B17-3/B19-3/P19-3 Troubleshooting Should an error occur, first check the following points. If the distortion is still not eliminated, the monitor should, if possible, be checked on another computer. If you are unable to solve the problem, please inform our help desk. Having this problem? No screen display (power indicator does not light) Check the following points: ► Check whether the main switch on the underside of the monitor is switched on (P19-3).
SCENICVIEW B17-3/B19-3/P19-3 Having this problem? Picture is wrongly adjusted Picture disturbances (vertical lines) Check the following points: ► Press the SELECT/MENU button to activate the function Factory Recall. The Auto Processing message is displayed. ► Press the EXIT/AUTO button to perform the autoadjustment of the screen. Picture disturbances (horizontal lines, picture noise) ► The screen becomes darker The background lighting has a limited lifetime.
SCENICVIEW B17-3/B19-3/P19-3 Notes regarding the DIN EN ISO 13406-2 standard Permanently unlit or lit pixels The standard of production techniques today cannot guarantee an absolutely fault-free screen display. A few isolated constant lit or unlit pixels (picture elements) may be present. The maximum permitted number of pixels faults is stipulated in the stringent international standard ISO 13406-2 (Class II).
SCENICVIEW B17-3/B19-3/P19-3 Technical data B17-3 B19-3 / P19-3 Visible diagonals: 43 cm 48 cm Dot pitch: 0.264 mm 0.294 mm 337.9 mm 270.3 mm 376.3 mm 301 mm Dimensions and weight Screen size: Width: Height: Maximal resolution: 1280 x 1024 1280 x 1024 Width: Height: Depth: 375 mm 469 mm 249 mm 412 mm 497 mm 249 mm Width: Height: Depth: 438 mm 418 mm 176 mm 484 mm 452 mm 176 mm Weight (without packaging): approx. 6.8 kg approx. 7.
SCENICVIEW B17-3/B19-3/P19-3 Environmental conditions Environment class 3K2, IEC 721 Rated range of operation: Humidity: 15 °C .... 35 °C 20 % .... 85 % Limit range of operation: Humidity: 5 °C .... 35 °C 20 % .... 85 % Condensation must be avoided. VESA-DDC-compatible VGA interface Your monitor is equipped with a VESA-DDC-compatible VGA interface. VESA-DDC (Video Electronics Standard Association, Display Data Channel) is used as the communications interface between the monitor and the computer.
SCENICVIEW B17-3/B19-3/P19-3 Pin assignment D-SUB 1 5 6 10 15 11 Pin Meaning Pin Meaning 1 Video input red 9 +5 V (DDC) 2 Video input green 10 Sync. earth 3 Video input blue 11 Earth 4 Earth 12 DDC-Data 5 Earth 13 H. sync 6 Red video earth 14 V.
