OPERATING MANUAL AIR CONDITIONER WALL MOUNTED TYPE Indoor Unit AST7 AST9 AST12 SERIES SERIES SERIES KEEP THIS MANUAL FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED P/N9373538035
CONTENTS SAFETY PRECAUTIONS .......................................... 1 FEATURES AND FUNCTIONS ................................. 2 NAME OF PARTS ...................................................... 3 PREPARATION .......................................................... 5 OPERATION .............................................................. 6 TIMER OPERATION .................................................. 9 SLEEP TIMER OPERATION ....................................
FEATURES AND FUNCTIONS Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). AUTOMATIC OPERATION *● HEAT & COOL MODEL (REVERSE CYCLE) Merely press the START/STOP button, and the unit will begin automatic operation in either the Heating, Cooling, Dry or Monitor modes as appropriate, in accordance with the thermostat setting and the actual temperature of the room.
NAME OF PARTS Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). 1 Fig. 1 2 3 Fig. 2 4 B 5 C OPERATION 9 0 A TIMER SWING 6 7 Fig. 3 8 Fig. 4 Fig. 5 D G H P * HEAT & COOL MODEL (REVERSE CYCLE) Q R E F K M U I L N T S COOLING MODEL V W X J O Fig. 7 Fig.
Fig. 1 Indoor Unit Fig. 5 Remote Control Unit 1 Operating Control Panel (Fig. 2) 2 MANUAL AUTO button D E F G H I J K L M N 3 Remote Control Signal Receiver 4 Indicator Lamps (Fig. 3) 5 OPERATION Indicator Lamp (red) ● Lights when unit is operating. *● The lamp will flash slowly when the defrosting operation (see page 17). *● The lamp will flash quickly (1 second on, 1 second off) when the selected operating mode can not be used (see page 18).
PREPARATION CAUTION! Turn on the Power Turn on the circuit breaker. Load Batteries (R03/LR03 × 2) 1 Press and slide the battery compartment lid on the reverse side to open it. Slide in the direction of the arrow while pressing the 2 3 mark. Insert batteries. Be sure to align the battery polarities ( ) correctly. Never mix new and used batteries, or batteries of different types. Batteries should last about one year under normal use.
OPERATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). To Select Mode Operation 1 Press the START/STOP button (Fig. 5 J). 2 Press the MASTER CONTROL button (Fig. 5 E) to select the desired mode. The indoor unit’s OPERATION indicator lamp (red) (Fig. 3 5) will light. The air conditioner will start operating.
OPERATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). When set to AUTO: * Heating : Fan operates so as to optimally circulate warmed air. However, the fan will operate at very low speed when the temperature of the air issued from the indoor unit is low. Cooling : As the room temperature approaches that of the thermostat setting, the fan speed becomes slower.
AUTO: COOLING MODEL ● Depending on the room temperature at the time operation begins, the operating mode will be switched automatically as shown in the accompanying table. Also, depending on the operating mode, the room temperature setting will cause the “standard” temperature to be set as shown.
TIMER OPERATION Before using the timer function, be sure that the Remote Control Unit is set to the correct current time (see page 5). To Use the ON timer or OFF timer 1 2 Press the START/STOP button (Fig. 5 J) (if the unit is already operating, proceed to step 2). The indoor unit’s OPERATION indicator lamp (red) (Fig. 3 5) will light. Press the TIMER button (Fig. 5 H) to select the OFF timer or ON timer operation. Perform steps 2 and 3.
SLEEP TIMER OPERATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operate is stopped. To Use the SLEEP timer While the air conditioner is operating or stopped, press the SLEEP button (Fig. 5 D). Both the indoor unit’s OPERATION indicator lamp (red) (Fig. 3 5) and the TIMER indicator lamp (green) (Fig. 3 6) will light.
ADJUSTING THE DIRECTION OF AIR CIRCULATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). Vertical (up-down) direction of airflow is adjusted by pressing the Remote Control Unit’s AIR FLOW DIRECTION button. Horizontal (right-left) airflow direction is adjusted manually, by moving the Air Flow Direction Louvers. Whenever making horizontal airflow adjustments, start air conditioner operation and be sure that the vertical air direction louvers are stopped.
SWING OPERATION Begin air conditioner operation before performing this procedure. To select SWING Operation Press the SWING LOUVER button (Fig. 5 L). The SWING indicator lamp (orange) (Fig. 3 7) will light. In this mode, the Air Flow Direction Louvers will swing automatically to direct the airflow both up and down. To Stop SWING Operation Press the SWING LOUVER button (Fig. 5 L) once again. The SWING indicator lamp (orange) (Fig. 3 7) will go out.
CLEANING AND CARE ● Before cleaning the air conditioner, be sure to turn it off and disconnect the power supply cord. CAUTION! ● Be sure the intake grille (Fig. 1 8) is installed securely. ● When removing and replacing the air filters, be sure not to touch the heat exchanger, as personal injury may result. Cleaning the Intake Grille Cleaning the Air Filter 1. Remove the intake grille.
Air Cleaning Filter Installation 1. Open the intake grille and remove the air filters. 3. Install the two air filters and close the intake grille. Mounting shaft Intake Grille 2 2 2 1 Intake Grille Bearing Knob 1 1 Intake Grille Intake Grille Mounting shaft Mounting shaft Knob Knob Intake Grille 1 2 2. Install the air cleaning filter set (set of 2). 1 Set the air cleaning filter into the air cleaning filter frame.
CLEANING AND CARE Replacing dirty Air cleaning filters Please purchase the separately sold replacement air cleaning filters and install them. 1. Open the intake grille and remove the air filters. Intake Grille 2 2 1 1 [AIR-PURIFYING FILTER (green filter)] ● Depending on the size of the room and the conditions in which the air conditioner is used, the normal life of the air-purifying filter is about three months.
TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). WARNING! In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the Power Supply Plug or turn off the circuit breaker, and consult authorized service personnel. Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. Always be sure to turn off your circuit breaker to ensure that power is completely off.
TROUBLESHOOTING Items to check Symptom CHECK ONCE MORE Doesn’t operate at all: See page ● Has the circuit breaker been turn off? ● Has there been a power failure? — ● Has a fuse blown out, or a circuit breaker been tripped? ● Is the timer operating? Poor Cooling (or *Heating) performance: 9 ● Is the air filter dirty? ● Are the air conditioner’s intake grille or outlet port blocked? ● Did you adjust the room temperature settings (thermostat) correctly? ● Is there a window or door open? — ● In the c
OPERATING TIPS Multi-type Air conditioner This indoor unit can be connected to a multi-type outdoor unit. The multi-type air conditioner allows multiple indoor units to be operated in multiple locations. The indoor units may be operated simultaneously, in accordance with their respective output. Simultaneous Use of Multiple Units Instructions relating to inverter (❖) are applicable only to “INVERTER MODEL”.
OPERATING TIPS Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).