Operating Manual Display A17-5 ECO / A19-5 ECO
Do you have ... ... any technical questions or problems? Please contact: • our Service Desk • your sales partner • your sales office The latest information about our products, useful tips, updates etc. is available on our website: "http://ts.fujitsu.com/support/" Further information can be found in the Service Desk list: "http://ts.fujitsu.com/support/servicedesk.
Copyright © Fujitsu Technology Solutions 2009 2009/09 Published by Fujitsu Technology Solutions GmbH Mies-van-der-Rohe-Straße 8 80807 München, Germany Contact http://ts.fujitsu.com/support All rights reserved, including intellectual property rights. Technical data subject to modifi cations and delivery subject to availability. Any liability that the data and illustrations are complete, actual or correct is excluded.
FUJITSU A17-5 ECO/A19-5 ECO Operating Manual Your LCD screen...
Windows 7, Windows Vista and Windows XP are registered trademarks of Microsoft Corporation. VESA, DDC and DPMS are registered trademarks of Video Electronics Standards Association. All other trademarks referred to in this publication are trademarks of the respective owners, whose legal protection is hereby recognised.
Contents Contents Your LCD screen... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Further information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents A26361-K1338-Z220-1-7619, edition 1
Your LCD screen... Your LCD screen... has a whole range of useful features and functions, e.g.: • • • TFT display (Thin Film Transistor; active matrix) minimal space requirements thanks to slim casing optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour purity right into the corners) • high degree of brightness and good contrast • high resolution (1280 x 1024) • presentation of up to 16.
Your LCD screen... Further information Details of how you set the resolution and refresh rate are provided in the documentation for your display adapter and the associated driver software. For ergonomic reasons, a screen resolution of 1280 x 1024 pixels is recommended. Because of the technology used (active matrix) an LCD monitor provides a totally flicker-free picture even with a refresh rate of 60 Hz. Notational conventions Pay particular attention to text marked with this symbol.
Important notes Important notes Notes Importantnotes In this chapter you will find information regarding safety which it is essential to take note of when working with your device. Safety instructions This device complies with the relevant safety regulations for data processing equipment, including electronic office machines for use in an office environment. If you have any questions about whether the device can be used in the intended environment, please contact your sales office or our Service Desk.
Important notes • • • • The device may only be operated in the wide format (0° landscape mode). The buttons of the control panel are located at the bottom in the middle of the monitor. Store this manual close to the device. If you pass the device on to third parties, you should pass this manual on with it. We recommend that you place your device on a durable, non-slip surface.
Important notes CE marking The shipped version of this device complies with the requirements of EEC directives 2004/108/EC "Electromagnetic compatibility" and 2006/95/EC "Low voltage directive". Energy Star EnergyStar The Fujitsu LCD colour monitor is equipped with a power management system which reduces the power draw in OFF mode to less than 1 W. As a result, the LCD monitor satisfies the requirements of the U.S. Environmental Protection Agency (EPA).
Important notes Disposal and recycling This device has been manufactured as far as possible from materials which can be recycled or disposed of in such a way that the environment is not damaged. The device may be taken back after use to be reused or recycled, provided that it is returned in a condition that befits its intended use. Any components not reclaimed will be disposed of in an environmentally acceptable manner.
Getting started Getting started Unpacking and checking the delivery The display surface of the device is sensitive to pressure and scratches. Always hold the device by the casing! The complete device package includes: • • • • • • one one one one one one monitor audio cable power cable CD with software and documentation Warranty Booklet "Safety" manual ► ► ► ► Unpack all the individual parts. Check the contents of the package for any visible damage caused during transport.
Getting started Setting up an ergonomic video workstation ► Do not position the video workstation opposite a window (1). 1 1 ► Position the monitor outside the reach of a light source (1). ► Position the keyboard where it is easiest to reach (1).
Getting started ► Position the monitor so that the eye distance to the screen (1) is around 50 cm. 1 50 cm 1 0 65 ► Position the monitor for optimum viewing (1). The monitor should under no circumstances fall outside the permissible viewing space (2). 30 60 30 65 2 2 Depending on the situation, it may be advisable to use a swivel arm or wall bracket (VESA FPMPMI), which are available from specialist dealers.
Getting started Removing monitor base Before you can use a swivel arm or a wall bracket, you must remove the monitor base. The display surface is susceptible to scratching! ► Switch off the monitor and pull the power plug out of the power socket. ► Lay the monitor on its face on a soft surface. ► Remove all cables. ► To remove the monitor base, undo the screws on the monitor base. You can now mount a swivel arm or a wall bracket in accordance with VESA FPMPMI using a hole spacing of 100 mm.
Getting started Connecting the device Please observe the safety information in "Important notes", Page 3. CE conformance and optimum picture quality are guaranteed only if you use the data cables supplied. ► Switch off the monitor and the computer. ► Disconnect the power plug from the computer. Connecting cables to the monitor The data cable supplied has two 15-pin D-SUB connectors for connection to the monitor and to the computer.
Getting started Connecting cables to the computer Information on the computer connections and interfaces is contained in the operating manual for your computer. ► Connect the data cable to the (active) monitor port on the computer and secure the plug-in connection by tightening the safety screws. ► Insert the other plug of the audio cable in the audio output of the computer. ► Plug the power connector of the monitor into a properly grounded mains outlet.
Operation Operation Switching the device on and off ! 1 = Buttons for the OSD menu (On-Screen Display) 2 = Power supply indicator 3 = ON/OFF switch ! Press the buttons upwards from below. The colour of the LED indicator changes as follows: LED indicator Blue Not lit Status Monitor and computer are switched on (normal mode). The monitor is switched off (or is in power saving mode - power consumption in standby and off mode ≤ 1 W). ► Switch the device on using the ON/OFF switch.
Operation Notes on power management If the computer is equipped with power management (power-saving mode), then this function can be fully supported by the monitor. The monitor does not distinguish between the individual energy-saving modes used by the computer (standby mode, suspend mode and OFF mode), as it is capable of immediately switching into the mode with the highest energy-saving effect. Level Power supply indicator Monitor Power consumption (typical) Operation Normal Blue light Max.
Operation Changing the monitor settings When putting the monitor into operation for the first time, the screen display should be optimally adapted to the display adapter used. Changing the monitor settings with the buttons of the control panel The buttons of the control panel have two functions.
Operation Locking the OSD menu The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings. ► Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor with the ON/OFF switch. The Action was executed message appears. Please proceed in the same manner to release the locked OSD menu again. Locking the ON/OFF button The ON/OFF switch can be locked to prevent accidental or unauthorised changes to the monitor settings.
Operation ► Press the SELECT/MENU button to activate the OSD menu. The main menu appears, with icons for the setting functions. The first icon, (Brightness/Contrast), is highlighted and the associated functions are visible in the right-hand menu field. ► Press the Forwards / button or the button to highlight another Back / icon (e.g. Image adjust). ► Press the SELECT/MENU button to select the highlighted icon. The Image adjust setup window will be displayed.
Operation OSD menu functions The OSD menu for analogue monitor operation is described below. During digital operation some functions are not available, they are not needed because of the digital transmission technology being used. Adjusting the brightness and contrast Call up the Brightness/Contrast setting window Brightness Set the brightness of the display Contrast With this function you change the brightness of the background lighting.
Operation Adjusting the volume Call the Audio setting window Volume Mute Set the volume for playback with the integrated loudspeakers Switch the loudspeakers off or on Setting the colour temperature and colours Call the Colour setting window Select the colour temperature The "warmth" of the screen colours is set using the colour temperature. The colour temperature is measured in Kelvin (K). You can choose between sRGB, 6500 K, 7500 K, 9300 K, Native and Custom Colour.
Operation Configuring function settings in the Advanced menu Open the Advanced settings window DDC/CI Activate/deactivate the DDC/CI function On = The DDC/CI function is activated (standard setting) Off = The DDC/CI function is deactivated Resolution Notifier Monitor information. The optimum resolution for this monitor is 1280 x 1024 pixels. When the function is active (On), a message will appear on the monitor after approx. 30 seconds if a different resolution is set.
Notes on ergonomic colour adjustment Notes on ergonomic colour adjustment If you select colours for the monitor in your application programmes, take note of the information below. The primary colours blue and red on a dark background do not produce the minimum required contrast of 3:1 and are therefore not suitable for continuous text and data entry.
Troubleshooting Troubleshooting Should an error occur, first check the following points. If the distortion is still not eliminated, the monitor should, if possible, be checked on another computer. If you cannot solve the problem, please contact our Service Desk.
Troubleshooting Having this problem? Check the following points: Picture disturbances (vertical lines) ► Press the EXIT / AUTO button to perform auto-adjustment of the screen. ► Press the EXIT / AUTO button to perform auto-adjustment of the screen. The background lighting has a limited lifetime. If your monitor display should become too dark, the background lighting will have to be replaced. Picture disturbances (horizontal lines, picture noise) The screen becomes darker ► Contact our Service Desk.
Explanatory information about standard ISO 9241-3 Explanatory information about standard ISO 9241-3 Bright or dark pixels It is not possible to guarantee an absolutely fault-free screen monitor with current production technology. A few isolated permanently bright or dark pixels (picture elements) may be present. The maximum permitted number of such faulty pixels is specified in the international standard ISO 9241-3 (Class II).
Technical data Technical data Condensation is not permitted, neither in the rated range of operation nor in the limit range of operation. Dimensions and weight Visible diagonals Dot pitch Picture size Width Height Maximum resolution Dimensions incl. Width monitor base Height Depth Weight (without packaging) Storable display modes Pixel error classes Class according to ISO 9241-3 Electrical data Analogue Video A19-5ECO 43 cm 0.264 mm 337.9 mm 270.3 mm 1280 x 1024 373.3 mm 376.9 mm 200.3 mm Approx.
Technical data Ambient conditions Environment class 3K2, DIN IEC 721 Rated range of operation 15 °C .... 35 °C Humidity Limit range of operation 20 % .... 85 % 5 °C .... 35 °C Humidity 20 % .... 85 % VESA-DDC-compatible VGA interface Your monitor is equipped with a VESA-DDC-compatible VGA interface. VESA-DDC (Video Electronics Standard Association, Display Data Channel) is used as the communications interface between the monitor and the computer.
Technical data SUB D port 5 1 10 6 15 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 11 Meaning Video input red Video input green Video input blue Ground Ground Video ground red Video ground green Video ground blue +5 V (DDC) Sync. ground Ground DDC Data H. sync V.
