User Manual Part 2

ManualsBrandsFujitsu Technology Solutions ManualsComputers & Accessoriespersonal computer

A26361-K520-Z100-4-7619

Preparation for use and operation

Please take note of the safety information in the chapter "Important notes".

Unpacking and checking the delivery

It is recommended not to throw away the original packaging material! It may be required for

reshipment at some later date.



Unpack all the individual parts.



Check the delivery for damage incurred during transportation.



Check whether the delivery agrees with the details in the delivery note.

Should you discover that the delivery does not correspond to the delivery note, notify your local

sales outlet immediately.

If you have received drives or boards with your PC, please do not install them until after

first-time setup. How to install drives and boards is described in the chapter "System

expansions".

Preparing the PC for use

First-time setup includes the connection of the devices (monitor, mouse, keyboard etc.) and the

setup of the supplied software.

When you set up the PC for the first time, you should carry out the following steps in the order

shown:

1. Decide where you are going to use the PC.

2. Connect the external devices to the system unit.

3. Check the rated voltage of the system unit and connect it to the line voltage.

4. Switch the PC on and follow the instructions on the screen.

Summary of content (8 pages)

PAGE 1
Preparation for use and operation ! Please take note of the safety information in the chapter "Important notes". Unpacking and checking the delivery It is recommended not to throw away the original packaging material! It may be required for reshipment at some later date. Unpack all the individual parts. Check the delivery for damage incurred during transportation. Check whether the delivery agrees with the details in the delivery note.
PAGE 2
Preparation for use and operation Setting up the PC Setting up the PC ! When installing your PC, give consideration to the recommendations and safety notes in the manual "Safety, Guarantee and Ergonomics". Set up the PC only in its correct orientation. The points to observe are illustrated on the following pages. We recommend that you place your equipment on a surface with good anti-slip qualities.
PAGE 3
Connecting devices Preparation for use and operation Ports for external devices The ports for external devices are on the rear and on the front of the system unit. The ports available on your device depend on the configuration level you have selected. The standard ports are marked with symbols like those below or similar symbols. Exact details of the position of the ports are supplied in the Technical Manuals for the boards.
PAGE 4
Preparation for use and operation Connecting devices Connecting the keyboard i Use only the keyboard cable supplied. Plug the round plug of the keyboard cable into the keyboard port on the system unit. Plug the other connector of the keyboard cable into the socket on the underside of the keyboard. Connecting the mouse Plug the connector of the mouse cable into the mouse port.
PAGE 5
Connecting devices Preparation for use and operation Connecting the monitor to the line voltage Prepare the monitor as described in the Operating Manual for the monitor. Plug the data cable of the monitor into the monitor port of the system unit. 2 1 Depending on the connector, plug the monitor power cable into either the system unit (1) or the grounded power outlet (2). ! You may only plug the monitor power cable into the monitor connector if the rated current of the monitor is less than 1.
PAGE 6
Preparation for use and operation Connecting the PC to the line voltage Connecting the PC to the line voltage 100 V - 125 V 200 V - 240 V 1 1 1 = Notch for inserting the screwdriver Check the rated voltage. ! The value marked with an arrow must agree with the local line voltage: 115 = 100 V to 125 V 230 = 200 V to 240 V If the rated voltage does not agree with the local line voltage, lift out the plug-in unit with a screwdriver (1), turn it and replace it.
PAGE 7
Unlocking/locking the system unit Preparation for use and operation Unlocking/locking the system unit With the casing lock you can mechanically lock the system unit, and with the drive cover you can block access to the drives. Unlocking the system unit 1 2 Turn the key counterclockwise (1). Slide the drive cover in direction of the arrow (2). Locking the system unit 2 1 Slide the drive cover in direction of the arrow (1) and turn the key clockwise (2).
PAGE 8
Preparation for use and operation Switching the PC on and off Switching the PC on and off 0 I 1 3 2 1 = Main switch 2 = ON/OFF switch 3 = Power-on indicator 0 = System unit is switched off I = System unit is ready-to-operate System unit is off The main switch (1) is in position 0, the power-on indicator (3) does not light, and the ON/OFF switch (2) is disabled.