Mobile Printer FTP-628WSL210 Series User's Guide FUJITSU COMPONENT LIMITED
Introduction Thank you for purchasing the FTP-628WSL210 Series Mobile Printer (hereafter referred to as “this product”). This User's Guide (hereafter referred to as “this guide”) contains precautions to use it safely and correctly. Before using this product, please be sure to read complete this guide to use it correctly. In addition, please keep this guide handy for future reference. If you have any suggestions or comments on this guide, please do not hesitate to let us know.
Precautions ■ Change of contents The contents of this guide and this product are subject to change without notice for the improvement. ■ Use to high safety application This product was designed and manufactured assuming general purpose use, such as standard industrial, general, personal and home use.
■ Regulatory Compliance For Customers in USA (FCC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
For Customers in CANADA (Industry Canada) This equipment complies with Industry Canada RSS210 rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Sa f e t y P r e c a u t i o n s ■ Meaning of Symbols The following symbols are used in this guide. Please understand well the meaning of each symbol and read this guide. Warning Indicates possibility of causing severe personal injury or death if not used properly. Caution Indicates that a minor or some personal injury may occur or that the product itself or other userʼs property may be damaged. Indicates danger, warning and caution. A concrete content is described on the side of this symbol.
■ Generic Precautions Warning Fire - Do not burn or heat. Failure to observe this may cause smoke or fire or breakdown. Fire - Do not pour water. This equipment is not waterproof. Failure to observe this may cause fire or burst or breakdown. Fire - Do not use or store the equipment in a hot environment. Failure to observe this may cause smoke or fire or breakdown. Fire Fire Breakdown Breakdown Modify 6 - Do not throw or drop. Failure to observe this may cause fire or burst or breakdown.
Caution Fire - Do not use direct sun or dusty place that contains the oil and iron. Failure to observe this may cause heat, fire, or failure. Fire - If charging is not completed beyond the predetermined charging time, unplug the charger, please stop the charge. The battery may leak by overcharging. Fire - Do not apply force to the cable. Failure to observe this may cause fire or electric shock. Injury - Do not use while driving a vehicle or walking.
■ Printer Warning Fire - Do not put metal objects or flammable objects into the gaps of the case. Failure to observe this may cause fire, or electric shock. - Do not use the printer in a location that is prohibited the generation of radio waves. Accident Might be in an accident by the malfunction of the instrument. Burn - Surely turn off the printer power and check that the printer head is sufficiently cooled down before cleaning. Failure to observe this may cause burn injury.
■ Battery Warning Fire Fire - Do not use other than the specified battery. Failure to observe this may cause fire, or electric shock. - Do not charge the battery in the charger other than the specified. Failure to observe this may cause fire, destruction. Fire - Do not short-circuit the electrode of the battery. Failure to observe this may cause heat, fire, destruction. Fire - Do not solder the terminal of battery. Failure to observe this may cause heat, fire, destruction.
■ AC Adaptor Warning Fire Fire Breakdown - Do not connect other than the specified voltage or/and frequency. Failure to observe this may cause fire or electric shock due to cable disconnection. - Do not use other than the specified AC adaptor. Failure to observe this may cause heat, fire, or destruction. - Do not use the AC adaptor for another device or purpose. Failure to observe this may cause damaging printer or/and battery.
■ Warning Label of Product This product is stuck label on the following alarm displays. This label must not peel off or erase the displays. Moreover, please contact the distributor when becoming difficult to see the display due to dirt etc. Warning display Contents HEAD ヘッド Since the print head and its support plate get a high temperature during printing, do not touch them directly.
Ta b l e o f C o n t e n t s 1 Kinds of Product..............................................................13 2 Preparation to print .........................................................14 2.1 Packing item ...........................................................14 2.2 Option Items ...........................................................15 2.3 Part Names .............................................................16 2.4 Inserting the Battery ................................................19 2.
1 Kinds of Product 1 Kinds of Product There are the following kinds of the product. Please note that the printer may not support the function by the printer model, even if there is a description in this guide. MODEL NAME FTP-628WSL210#20-R a : Supply item (Refer to Table 1-1) b : Interface (Refer to Table 1-2) Table 1-1. Supply items a Contents 20 Printer Battery AC Adaptor AC Cable Belt Fixture ○ ○ ○ × × Table 1-2.
2 Preparation to print 2 Preparation to print 2.1 Packing item The following are attached to this product. Please open the box and confirm to item in the box. If it is insufficient, please ask the distributor.
2 Preparation to print 2.2 Option Items To use this product better, the following and optional parts are prepared. Please confirm how to buy to the Acquisition origin of this product.
2 Preparation to print 2.3 Part Names ■ Front Side (Cover Close) 1 2 6 3 16 4 7 5 8 1 Paper Cover : This is opened and paper is set. 2 Paper Cutter : To cut paper. 3 Status LED : The state of printer is displayed. 4 POWER Switch : To turn the power supply on or off. 5 FEED Switch : To feed paper. 6 Cover Open Lever : To open the cover. 7 USB Connector : This is opened and it connects PC etc. 8 Battery Cover : This is opened and the battery is set.
2 Preparation to print ■ Front Side (Cover Open) 9 10 9 Platen Roller 10 Warning Label 12 : To feed paper. : This shows warning when using printer. 11 11 Thermal Head : This applies heat to paper. 12 Paper Sensor : This sensor detects the state of paper.
2 Preparation to print ■ Rear Side 14 13 15 13 Screw for Belt Fixture : This fixes Belt Fixture. 14 AC Adaptor Connector : This is opened and AC adaptor is connected. 15 Product Label 18 : Printer Type and etc are displayed.
2 Preparation to print 2.4 Inserting the Battery Caution Life of the battery charging is about 500 times. (At the normal temperature) If the degradation battery is used, not only the equipment malfunctions but also destruction might be caused. 1. Please open the battery cover by pushing the lock of the battery cover and pulling the cover forward. Battery cover Cover lock 2. Please turn the label surface of the battery below and insert the surface of the electrode. Battery ② 3.
2 Preparation to print 2.5 Connecting AC Adaptor(Charging) The battery is charged by the charger capability with built-in this printer. Caution Please stop charging at once if an abnormal charge is generated. 1. Please connect the AC cable with the AC adaptor, and connect the AC plug with the outlet. 2. Please open the connector cover for the AC adaptor, and connect the DC output terminal of the AC adaptor with the connector for the AC adaptor.
2 Preparation to print 2.6 Connecting AC Adaptor(Operating) This product can be operated also with the AC adaptor. 1. Please connect the AC cable with the AC adaptor, and connect the AC plug with the outlet. 2. Please open the connector cover for the AC adaptor, and connect the DC output terminal of the AC adaptor with the connector for the AC adaptor. AC cable AC adaptor Connector for AC adaptor Cover [Side view] 3. Please turn on the power supply of the printer. Please refer to chapter 3.
2 Preparation to print 2.7 Setting Paper 1. Please open the paper cover by pushing the cover open lever in the direction of the arrow and going up. Cover Open Lever Thermal Paper (Thermosensitive Side) 2. Please set the paper in the printer. 3. Please put out the edge of the paper and close the paper cover. Please push the center of the paper cover firmly when closing.
2 Preparation to print 2.8 Setting Belt Fixture The printer can be attached to the waist belt with belt fixture of optional parts. The belt fixture is recommended to be attached with the following directions. How to attach it 1. Please remove the screw for the belt fixture on the printer bottom surface. 2. Please tighten the screw for the belt fixture after disposing it in the direction of the favorite. Important - If the belt fixture runs aground in the stopper, it cannot install to it correctly.
3 Operating Procedures 3 Operating Procedures 3.1 Turning On 1. Please keep pushing the POWER Switch until lighting to green the State LED. 2. It is possible to turn off power by keeping pushing the POWER Switch until the State LED is turned off.
3 Operating Procedures 3.2 Test Print This product has the test print function. The setting of the printer can be confirmed in this test print. 1. Please turn off the power and push the FEED switch. 2. Please turn on power with the FEED switch pushed. Then, the test print starts. 3. When the test print ends, the printer automatically turns off the power supply. 4. Please turn off power when you want to stop the test print. 5. Please refer to the next page for the content of the test print.
3 Operating Procedures Checked pattern The thermal head open circuit etc. can be confirmed. Version The firmware version can be confirmed. ---------------628AD Ver 1.00 ---------------- INTERFACE : Bluetooth/USB HAND SHAKE : Non process Setting information etc The setting information etc can be confirmed. This print example is the following content.
3 Operating Procedures 3.3 USB Communication It explains the example of the connection method in the USB communication to print it from the terminal like a personal computer as follows. 1. Please prepare the USB cable. The plug on the printer side (device side) is mini B type. 2. Please open the USB connecter cover and connect the plug of cable to the USB connector. 3. Please connect the plug of host side to the host terminal connecter. 4.
3 Operating Procedures 3.4 Bluetooth Communication It explains the example of the connection method in the Bluetooth communication to print it from the terminal like a personal computer as follows. 1. Please turn on the power of printer. 2. Please search the Bluetooth device by the application in the host terminal. 3. The device name of the connected printer is displayed. Then, please select the device and connect it. 4. Please input "9999" when the PIN code is demanded.
3 Operating Procedures 3.5 Printer Error The error occurs when the printer cannot print/work normally. The category of error is notified by the LED and the communication when the error is occurring. Please return to normally status by removing the cause when the error is occurring. The following example explains the cause and way to release of each error. Error Paper End Paper Cover Open Thermal Head Temperature Error Cause Solution - There is no paper in the paper cover.
3 Operating Procedures Error Supply Voltage Error Mark Undetection Hardware Error MCU Operation Error RAM Error Bluetooth Error Charge Error Cause - The residual quantity of the battery has decreased. - The AC adaptor is out of order. (At the AC adaptor operation) - The mark of paper is not correctly printed. - Garbage has collected in the paper sensor. - The printer is out of order. ・ The battery is out of order. ・ The AC adaptor used for the charge is out of order.
4 Indicator Lights 4 Indicator Lights The state of the printer error and the battery residual quantity is confirmed by the LED display. Important It may be difficult to see the LED display in a bright place under direct sunshine etc. 4.
4 Indicator Lights 4.
4 Indicator Lights 4.3 Charging Printer Status LED Indications (LED Symbol ○:Lighting, ●:Blinking) Gree n Ora nge Re d Blink Cycle (Unit [msec]) Chargeing ○ ON O FF ON O FF Full Charge Charge Error (Over charge, Over discharge, Over time) ● Charging Chargin g Full charge 950 ON O FF 950 4.
5 Maintenance 5 Maintenance Please maintain this printer regularly. Caution - Do not do the maintenance task for the printer with including the battery or connecting the AC adaptor. - Do not absolutely maintain, disassemble and repair the part not explaining in this chapter. 5.1 Thermal Head Please maintain the thermal head once a month. 1. Please open the paper cover. (Refer to chapter 2.7) 2.
5 Maintenance 5.2 Platen Roller Please maintain the platen roller once a month. 1. Please open the paper cover. (Refer to chapter 2.7) 2. Alcohol is soaked into the soft one such as cotton buds, and it wipes it gently until the thermal head is cleaned. Please use IPA on the market for alcohol. (Isopropyl alcohol) 3. Please wipe off with a cloth that dries and is soft, and please close the paper cover after it waits until naturally drying. 5.3 Paper Sensor Please maintain the paper sensor once a month. 1.
5 Maintenance 5.4 Paper Cover If the paper cover came off, please repair according to the following procedures. 1. Please push the opening and closing fulcrum of the paper cover to the printer with the paper cover opened, and it connects the printer. Opening and closing fulcrum of paper cover 2. Please confirm the correct connection by opening and closing the paper cover 2-3 times.
5 Maintenance 5.5 POWER/FEED Switch If the Power switch or the FEED switch came off, please repair according to the following procedures. 1. Please push and fix the switch to be suitable for a quadrangle on the switch side and for hole of the case Switch side. Please fix the FEED switch to be suitable of the oval. [Front view] [Side view] 2. Please confirm that the repaired switch works correctly.
6 Troubleshooting 6 Troubleshooting ■ Power Problem Printer does not turn on Is there a battery? or Isn't it reversed? Is the battery charged enough? Is the POWER Switch correctly pushed? Is the battery old? Battery does not be charged or Charge error occurs Is there a battery? or Isn't it reversed? Is the battery old? Power supply cuts suddenly Battery discharge early 38 Cause Is the AC adaptor correctly connected? Have the battery already been a full charge? Is not the power turned on? It is not
6 Troubleshooting ■ Communication Problem Cause Solution Printer does not communicate Is not the power turned off? Is the application or the driver for this product used? Is USB cable correctly connected? Please turn on the power. (C. 3.1) Please use the application or the driver for this product. Please connect the cable correctly. (C. 3.3) Please use the cable without the breakdown.
6 Troubleshooting ■ Print Problem Cause Solution Printer does not paper feed or Paper jam occurrs Is not the power turned off? Is the paper correctly set? Is the paper cover closed? Does not the printer error occur? (C. 4) Isn't the platen roller dirty? Is not the power turned off? Is the paper correctly set? Is the paper cover closed? Does not the printer error occur? (C.
6 Troubleshooting ■ Others Problem Cause Solution Print starting location is incorrect Does the mark detection operate correctly? (C. 4.2) Printing is slow Isn't the remainder of the battery a little? Is the battery old? Please remove the cause of the mark detection error. (C. 3.5) Please charge the battery. (C. 2.5) Please exchange it to new battery. It is not a breakdown though the print slows when there are many blacks.
7 Specifications 7 Specifications 7.1 Printer specifications Items Print Method Resolution Dimensions Weight Max Print Width Print Speed Character Barcode Interface Conformity Standerds Operating Temperature Operating umidity Storage Temperature Storage Humidity 42 Contents Thermal Line-dot Printing 8dot/mm(203dpi) 84×136.5×43.6mm About 220g Including a battery, Excluding a paper About 48mm Max 40mm/sec Battery full charge, Print ratio 12.
7 Specifications 7.
8 Recycle 8 Recycle This symbol means: Do not dispose of this product together with your household waste! Please refer to the information of your local community or contact our dealers regrading the proper handling of end-of-life electric and electronic equipments. Recycling of this product will help to conserve natural resources and prevent potential negative consequences for the environment and human health caused by inappropriate waste handling.
9 Appendix 9 Appendix 9.1 Product Support If you have the question on the product, please inquire of the distributor or the following. Moreover, when you request the breakdown and the repair, please tell us the model name and the product serial number in addition to information on the symptom etc. Technical Support Section FUJITSU COMPONENT LIMITED (Japan) Global Marketing Dept.2 Tel: +81-3-5449-7014 Fax: +81-3-5449-2628 E-mail: promothq@fcl.fujitsu.
9 Appendix 9.2 Bluetooth Communication (1) Android Terminal 1. Please turn on the power of printer. 2. Please open "Settings" - " WIRELESS & NETWORKS" from the menu of terminal, and turn on Bluetooth. 3. Please open the "Bluetooth”, and tap "FTP-628WSL…". (Please tap "SEARCH FOR DEVICES", if it does not appear) 4 Please input the PIN code, and tap "OK". PIN code is "9999" in the state of the factory shipment. (The PIN code input is unnecessary at the connection of second and subsequent) 5.
9 Appendix (2) iOS Terminal 1. Please turn on the power of printer. 2. Please open "Settings" - "General" - "Bluetooth" from the menu of terminal, and turn on Bluetooth. 3. Please tap "FTP-628WS…" from "Devices". 4. Please input the PIN code, and tap "Pair". PIN code is "9999" in the state of the factory shipment. (The PIN code input is unnecessary at the connection of second and subsequent) 5. When the connection with the printer succeeds, "Connected" is displayed to "FTP-628WS…". 6.
MEMO
Mobile Printer User's Guide FTP-628WSL210 Series L0NA02265-L11802RS Pablished by FUJITSU COMPONENT LIMITED Aug, 2012 Rev 1