Notice to the user Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. Illegal operation is punishable by fine or imprisonment or both. THANK YOU We are grateful you choose BelFone series professional radio communications products! Since 1989, BelFone has been always engaging in research and exploration of radio communications technologies, In order to lead intelligent technologies in the industry.
WARMING! Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• Transmit no more than the rated duty factor of 50% % of the time. To transmit (talk), push the Push-To-Talk Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50 % of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance).
Precautions It’s important that the operator is aware of and understands hazards common to the operation of any radio .Please observe the following safety precautions to prevent radio damage or personal injury. The following precautions shall be observed during operation, service and repair of this radio.
Contents Supplied Accessories......................................................................................................................... 6 Accessories ............................................................................................................................. 6 Installation of Accessories ................................................................................................................ 7 Getting Acquainted .........................................................
TX Permission ................................................................................................................................ 45 Battery Saver ................................................................................................................................... 45 Low Battery Warning ...................................................................................................................... 46 Monitor ...................................................................
Screws Charger Li-ion ion Battery Installation of Accessories Installation/ Removing the Antenna Hold the supplied antenna by its base, then screw it into the connector on the top panel of the radio until fasten. Turn the antenna anti-clockwise clockwise to remove it.
Installation// Removing the Belt Clip Attach the belt clip using the two supplied3 * 4mm binding screws. Attaching/Removing the Strap Thread the hand strap to the loop back of your two-way two radio.
Attaching/Removing the Battery Warning! 1. Don’t short-circuit circuit the battery, it may cause the battery damaged or burst into flame; 2. Never attempt to remove the casing from battery, that avoid to short the battery terminal; 3. Battery is flammable objects, don’t don t throw it into fire or don don’t use it on dangerous area. Match the guides of the battery with the corresponding grooves on the upper rear of the radio, then press the battery until a click is heard to lock it in place.
Note: Don’t attach / remove the battery if the radio turned on. Battery Information New battery is shipped not fully charged from the factory, please charge your battery before using it, charging a new battery for 5 hours before initial use. The maximum battery capacity and performance is achieved after three full charge/discharge cycles. If you notice the battery power runs lows, please recharge the battery.
than normal performance; it is time to buy a new battery. To Prolong Battery Life 1. Battery performance will be greatly decreased at a temperature below 0℃, a spare battery is necessary in cold weather, the cold battery unable to work in this situation may work under room temperature, so keep it for later use. 2. The dust on the battery contact may cause battery breakdown, please use a clean dry cloth to wipe it before attaching the battery to the radio. Battery Storage 1.
Battery is charging Charge Indicator glows red Battery is fully charged Charge Indicator glows green Charge Steps: 1. Plug the AC connector of the switching power into the AC outlet socket. 2. Place the battery or the radio is attached with a battery in the charger. 3. Making sure the battery is connected to the charger, the charging process initiates when the charger indicator glows red. 4. The charger indicator glows green when the battery is fully charged, please remove the battery then.
Getting Acquainted ① ② ③ ⑨ Power switch/volume adjust keys ⑩ LED Indicator 11 ○ Speaker 13 Orange Button OK Key P1 Key
④ ⑤ Direction Up 12 ○ PTT Key Return Key 13 ○ Side Button 1 P2 Key 14 ○ Side Button 2 Direction Down 15 ○ ⑥ ⑦ ⑧ MIC-SP-USB USB Port Microphone Microphone(MIC) Basic Operation LCD Icons / / / Signal A&D Mode Encryption On High /Low The Keypad Locked Power inbox/outbox is Strength / full Emergency Scan On Unread Disable All message Alert Tones Moniting Receiving Voice Analog Connect to Duplex Mode Mode USB Missed Call VOX On Si Simplex Mode Earphone is Roaming On Log
All Call Scan Menu First Priority Scan Channel Contacts Read Message Menu SMS Menu Second Priority Scan Channel Unread Single Message Frequency re repeater feature is enabled Zone Menu Message Send Ad Hoc feature Successfully is enabled Turning the power on /off Long press the power switch/volume adjusting keys about 2 seconds to turn the power on, the power on tone will sound. Then long press the power switch/volume adjusting keys about 2 seconds to turn the power off.
Selecting a Channel Short press the [power switch/volume adjust keys] to switch the function to knob mode then rotate it to select a channel. Rotate the knob clockwise to increase the channel number, or rotate the knob anti-clockwise to decrease the channel number; also press the direction up or down key to select a channel, while enable all tone alert ,handover channel will hear a channel number.
compatible digital, press 【Digital/Analog Switch】button to switch to digital compatible analog mode. Note: Digital/Analog Switch function only switching the channel mode temporarily, while you restart the radio or rotate channel selector knob, the current channel will resume to default mode. Call Each digital channel may can transmit a private call, a group call or an all call; on analog channel press and hold down the PTT key to transmit.
then press PTT key to transmit a private call; (3) Enter Contacts menu and go to manual dial menu or press programmed “Manual Dial” key, input a private call number you want to call, then press PTT key to transmit; (4) Enter Call Log menu to select the private call number you want to call, then press PTT key to transmit a private call; (5) You can set the One Touch Call key as private call feature, then press programmed key to transmit a private call.
key to transmit an all call; (2) Enter Contacts menu to select the all call number you want to call, then press PTT key to transmit an all call; Duplex Call The radio supports full duplex mode communication that is you can transmit and receive at the same time. Only the current channel of transmitter and receiver are set as duplex mode that you can make a full duplex call.
the preset time period to call back. Calls on Analog On analog channel, press and hold down the PTT key to transmit, release PTT key to receive. Button Setting For enhanced convenience, you may program the all buttons, short and Long press of a key can be assigned with different functions. Programmable keys are including functions listed below: No.
12 Top Contacts Quick access to Top Contacts menu 13 Home Screen Quick return to Home Screen 14 Boot Menu List Quick access to Boot Menu List menu 15 Lone Worker On/Off To enable or disable lone worker quickly 16 Man Down On/Off To enable or disable man down quickly 17 Contact List Quick access to Contact List menu 18 Message Quick access to Message menu 19 Monitor On/Off To enable or disable monitor quickly 20 Monitor Momentary 21 Keypad Lock To enable or disable keypad lock qui
36 Vibration Setting To enable or disable vibration quickly 37 GPS On/Off To enable or disable GPS quickly 38 Disconnect To hang up current call quickly 39 Radio Check Quick access to Radio Check menu 40 Remote Monitor Quick access to Remote Monitor menu 41 Radio Disable Quick access to Radio Disable menu 42 Radio Enable Quick access to Radio Enable menu 43 Site Lock Switch Quickly to enable or disable lock site function.
Functions and Operations Contacts Contacts list can contain a maximum of 1000 members, including private call, group call, all call. On the contacts, you can view the frequent contacts or all contacts, add new group or contacts, manual dialing. 1. Group Call / All Call While the contacts type as Group or All Call, you can select the menu to view its ID or send message. 2.
can enable the microphone of the target radio, and monitor its activities. Device Enable Device Enable: Allow a user to send "Device enable" command to the target killed device, to allow it to be used normally. Device Disable Allow you to send the Radio Disable command to a private contact to disable its radio, except remote monitor, all other functions are disabled, The radio must be reprogrammed for reuse or enabled by the Radio Enable command. ●Edit Name: Modify the name of a private call contact.
You can add a private call contact to the contact list. When edit name, press” *” key to delete, press “#” to switch input method, name input 16 characters at most; then input number, the available number range is 1~16776415. After add a Private Call contact successfully, on contacts list will show new contact. 5. Manual Dial You can manually input the private number or group number for calling, on manual dial menu, press * key can switch input private or group number, then press PTT key to transmit.
Note: Preset text messages also can assign to one touch call, and press the programmed key to send messages 3. Inbox The Inbox can save up to 50 0 received messages. Inbox the unread message displays: , read message displays: . For each message, you can choose to perform any of these operations: Reply, Forward and Delete. 4. Outbox Outbox can save up 20 0 sent messages.
The missed calls list can save up to 20 private calls, after selecting an entry, you can view the details or add it to contact list or delete it. Scanning 1. Scan On/Off While current channel add scan list and the list contain 2 channels at least, you may enable the feature. Scanning allows the device to search the scan list connected to the current channel to locate qualified channel for receiving or voicing.
2. View / Edit Allow a user to view/edit edit the scan list via menu, menu allows a user to view the scan group members or add a new member to the scan list, the list contain 16 channels at most. Also you can edit the members as priority channel, indicates priority channel 1, indicates priority channel 2, each scan list may contain two priority channels at most. Roam This feature allows the radio communicate between available sites in the IP Site Connect system.
Settings 1. Settings Allow a user to configure basic settings for the radio. ●Language: ●LED The radio supports two languages: Chinese and English. indicator: Allow a user to enable or disable the LED indicator via menu. All LED indicators including: TX LED, RX LED, Scan/ Roam LED, Low Battery LED, Call Hang LED.
digital channel. Voice End Tone To set whether the radio will give tone indication when the radio ending receives voice. Private Call To set whether the radio will give tone indication when the Tone radio receives a private call. Group Call To set whether the radio will give tone indication when the Tone radio receives a group call. Call End Tone To set whether the radio will give tone indication when the radio release PTT key and the hang time expires.
vibrate for an incoming private call, a new message or a call alert. ●VOX: While this function is enabled, you can enjoy hands-free hands free communication. The radio will automatically begin transmitting when you speaking, and terminate transmitting when you stop talking with no need of PTT press. Allow llow user to set the VOX level (level 1-8) and VOX delay(0.5~10second) via menu.VOX menu on indicate by : . Note: The VOX feature only is used if you are using a supported headphone.
Note: This menu is effective if power on password is set via programming software. ●Boot Interface: Allow a user to enable or disable the boot screen via menu. If the Intro screen is enabled, while the radio power on, the screen display BelFone Logo and device name; while the Intro screen is disable, the screen only displays device name. ●Covert Mode: If enable covert mode function, the radio will be totally silent without any UI indication.
2. Channel Settings Channel configure function is used to modify the current channel parameters, on digital channel, it allows you to modify Channel Name, Sending Timeout, RX/TX frequency, Color Code, Slot Selection, Encrypt Setting, TX contacts, RX Group List; on analog channel to modify Channel Name, Sending Timeout, RX/TX frequency, Subsonic, Single Freq Repeater and AD Hoc network. ●Channel Name: To set current channel alias, it contains 16 characters at most.
●TX Contacts: To select a contact from all contacts list as current channel default address; ●RX Group List: To set current channel RX group list. ●Single Frequency Repeater: To set current single frequency repeater feature, you can enable or disable it. ●Ad Hoc Network: To set current Ad Hoc network feature, you can enable or disable it. 3.
be manually transmitted to an individual user. The radio also supports query location information of another radio user if obtains the query command. GPS data compressed feature: via the programming software can enable the data compression feature, which can reduce the capacity of data transmission and improve the efficiency of data transmission. Note: The RFID and Recording features of accessory are unsupported temporarily.
locally and display the icon . Emergency Alarm Mode: Emergency Alarm: In this mode, you can send alarm information, while receive ACK or reach the maximum retries will exit emergency mode. Emergency Alarm with Call: You can press programmed” Emergency On/Off” key to send emergency information, then press PTT to transmit an emergency call.
automatically. While the receiver only long press the programmable button programmed as [Emergency Off] to exit emergency mode. Analog Emergency Emergency alarm on analog channel only supports the emergency type as siren only, to enter emergency alarm state, short press the programmable button programmed as [Emergency On], the siren will sound locally and the icon will show. Long press the programmable button [Emergency Off] to exit the alarm mode.
Press the programmable button programmed as [Lone Worker On/Off] to disable it Via the programming software, Lone Worker On/ Off item is not checked Man Down When this feature is enabled, the radio automatically sends an alarm for help if it is positioned aslant or keeps motionless long time.
Press the programmable button programmed as [Man Down On/Off] to disable it; Via the programming software, Man Down On/ Off item is not checked Encryption The encryption feature can encrypt your audio signals and data to guarantee the privacy of your communication, via the programming software user can select encryption type as XOR, enhanced XOR, ARC4, AES256 or dynamic encryption. XOR and enbanced XOR encryption only encrypt the audio signals.
To select an encrypt key from the key list when the encryption feature is enabled. Note: This feature is effective on digital channel. TDMA Direct Mode If enable TDMA direct mode, the members in the same group call must use the same slot, one frequency supports calls in two slots synchronously in order to avoid interfering communications in the other slot. Note: This function is available only in digital operation.
Direct Mode with with Different Frequency If enable direct mode feature you can transmit with different frequency directly, only the transmitter and receiver are set direct mode simultaneously and the TX frequency of the transmitter transmitter is the same as the RX frequency of the receiver, you can directly communicate in DM mode. Single Frequency Repeater Re Feature The radio supports single frequency repeater re feature, with this feature enabled, the icon: appears.
● Allows the user to enable the single frequency repeater re feature to current channel, but can’tt enable the Ad Hoc network feature at the same time. Ad Hoc Network Feature The radio allows the user to enable the Ad Hoc oc network feature to expand the long distance transmission and coverage of radio’s radio signal. With ith this feature enabled the icon: appears in this way, the current channel can appears, can’t initiate a confirmed private call or other with acknowledge service.
Networking Feature The radio supports to login the system for corresponding operation, the system contains belfone intelligence connection system or trunking system. If the radio has registered with the system successfully that can realize the interconnected communication under the networking mode. Note: The networking is an optional feature.
●Emergency Priority Interrupt: If there is an active call on current channel, and a user with higher priority level to send emergency service will terminate the ongoing activity automatically. ● Message Priority Interrupt: If there is an active call on current channel, and a user with higher priority level to send a short message will terminate the ongoing activity automatically, so as to make sure the message is sent successfully.
TX Permission Digital Channel This feature can restrict the channel if it is already in use you will be unable to transmit. There are three options available: always, color code free, channel free, if choose always, whenever press PTT key to transmit directly; If choose color code free, you will be unable to transmit on the channel if the color code is already in use; If choose channel free, you will be unable to transmit on the channel if it is already in use.
You can set battery saver time ratio as: 1:1, 1:2, 1:3, 1:4, the default setting is 1:2. Low Battery Warning When your battery gets low, LED indicator glows red and with a warning tone: “Please Charge”,please please replace the battery or charge the battery in time. The radio will turn off automatically while battery is too low. Monitor On analog or digital channel, enable the Monitor feature, the icon: appears.
Normally Open, Normal, Strengthen. Compander The compander can be enabled only for analog channel, transmitted signals are compressed before being sent and received signals are expanded when they receive. This background feature allows higher clarity of signals, avoiding excessive noise. CTCSS/CDCSS On analog channel, you can set unique CTCSS/CDCSS to guarantee the privacy of your communication, on digital compatible analog channel or analog compatible digital channel, is must attach to CTCSS/CDCSS.
CTCSS Frequency Table CTCSS No. Freq. [Hz] CTCSS No. Freq. [Hz] CTCSS No. Freq. [Hz] CTCSS No. Freq. [Hz] 1 67.0 14 103.5 27 159.8 40 199.5 2 69.3 15 107.2 28 162.2 41 203.5 3 71.9 16 110.9 29 165.5 42 206.5 4 74.4 17 114.8 30 167.9 43 210.7 5 77.0 18 118.8 31 171.3 44 218.1 6 79.7 19 123.0 32 173.8 45 225.7 7 82.5 20 127.3 33 177.3 46 229.1 8 85.4 21 131.8 34 179.9 47 233.6 9 88.5 22 136.5 35 183.5 48 241.8 10 91.5 23 141.
7 D047N D047I 35 D245N D245I 63 D516N D516I 8 D051N D051I 36 D251N D251I 64 D532N D532I 9 D054N D054I 37 D261N D261I 65 D546N D546I 10 D065N D065I 38 D263N D263I 66 D565N D565I 11 D071N D071I 39 D265N D265I 67 D606N D606I 12 D072N D072I 40 D271N D271I 68 D612N D612I 13 D073N D073I 41 D306N D306I 69 D624N D624I 14 D074N D074I 42 D311N D311I 70 D627N D627I 15 D114N D114I 43 D315N D315I 71 D631N D631I 16 D115N D115I 44 D331N
1. 2 3. The radio cannot be Remove the battery and then reattach it. powered on Recharge or replace the battery. During receiving, the Increase the volume level. voice is week, Turn off the radio and reattach the antenna. discontinuous or Check the battery voltage, if the voltage is low totally inactive. please recharge or replace the battery. The voice is unclear. Modify the frequency to avoid be interrupted by radios using the same frequency.
Specifications General Frequency Range 136~174 MHz Channel Capacity 1024 Zones 128 Channel Spacing For FCC: 12.5KHz Operating Voltage DC 7.4V (±20%) Operating Voltage 2300mAh Frequency Stability ±0.5ppm Working Temperature Charging 0℃~40℃ Discharging 0℃~55℃ Dimensions 56(L)*33(W)*129(H)mm Weight 315g(including battery) Receiver Sensitivity Analog:0.28μV(12dB SINAD) Digital:-116dBm /BER1% Adjacent Channel Selectivity 60dB@12.5kHz Intermodulation 65dB@12.
Audio Distortion ≤5% Transmitter RF Output Power High Power:4W Low Power:1W Conducted Spurious Emission -36dBm<1GHz/-30dBm>1GHz Modulation Limiting ±2.5kHz@12.5kHz FM Noise 40dB@12.5kHz Audio Distortion ≤5% Note: 1. The max working temperature including: master radio, battery and power adaptor; 2. Please turn off the power of the radio before charging, and prohibit operating the radio while charging; 3.