Notice to the user Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. Illegal operation is punishable by fine or imprisonment or both. THANK YOU! We are grateful you choose BeiFeng series professional radio communications products! Since 1989, BeiFeng has been always engaging in research and exploration of radio communications technologies, In order to lead intelligent technologies in the industry.
FCC radiation exposure statement This radio is intended for use in occupational/controlled applications where users have been made aware of the potential risks for exposure and can exercise control over their exposure. This product is not authorised for general population, consumer or similar use. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
Cette radio a été conçue pour un usage professionnel dans un environnement contrôlé, où les utilisateurs sont pleinement conscients du danger potentiel de l’exposition à laquelle ils sont soumis et peuvent exercer un contrôle sur cette exposition. Ce dispositif radio N’EST PAS autorisé pour l’ensemble de la population, les consommateurs en général, ni pour une utilisation similaire. Cet émetteur ne doit pas être co-localisés ou fonctionner en conjonction avec une autre antenne ou émetteur.
◆Don’t leave the transceiver in direct sunlight for a long time, don’t place the transceiver on extremely heat, damp, dusty area, and don’t put it on unstable surfaces; ◆When restriction or warnings are posted regarding the use of radio devices, please obey the regulation turn the transceiver power off; ◆Use of the radio while you are driving may be against traffic laws, please prohibit using it ; ◆If you notice any problems on the radio, please turn off at first. Then contact with local dealer.
One Touch Call ........................................................................................ 19 Talk Around ............................................................................................. 20 TX Power ................................................................................................. 21 Squelch Level ..........................................................................................21 Digital Emergency .............................................................
Belt Clip 1 Charger 1 Li-ion Battery 1 Screws 2 Instruction Manual 1 Warranty Card 1 Certificate 1 Antenna Charger Strap Li-ion Battery Belt Clip Screws Installation of Accessories Installation/ removing the antenna Hold the supplied antenna by its base, then screw it into the connector on the top panel of the radio until fasten. Turn the antenna anti-clockwise to remove it.
Attaching/Removing the belt clip Attach the belt clip using the two supplied3*4mm binding screws. Attaching/Removing the Strap Thread the hand strap to the loop back of your two-way radio.
Attaching/Removing the Battery Warning! Don’t short-circuit the battery, it may cause the battery damaged or burst into flame; Never attempt to remove the casing from battery, that avoid to short the battery terminal; Battery is flammable objects, don’t throw it into fire or don’t use it on dangerous area. Match the guides of the battery with the corresponding grooves on the rear of the radio, then push the battery until a click is heard to lock it in place.
To remove the battery, please turn the power off then push the latch up to unlock the battery pull the battery away from the radio. Note: Don’t attach / remove the battery if the transceiver turned on. Li-ion battery features ● New batteries are activated from factory; please charge your battery before using it. The maximum battery capacity and performance is achieved after three full charge/ discharge cycles.
for a long time, and store your battery in a cool, dry location. ● Charge your battery about 50% before you store it for a long time, so that can prevent to decrease the battery performance. ● As the battery is charged and discharged repeatedly, the battery capacity decreases, even if the battery is unused, the battery degrades, and store battery in a high temperature will shorten its lifecycle.
4、 The charger indicator glows green when the battery is fully charged. Note: Mack sure the battery is connected to the charger, but the charger indicator not glow, Maybe the battery /charger has damaged or temperature out of the limit. Attaching the Speaker/Microphone Open the accessory jack cover, then align the plug with the accessory jack and tighten the screw on the plug.
Getting Acquainted ① Channel Selector Knob Turn the knob to select channel 1-16, if a channel is available, there will be a channel number sounds. ② Power switch/volume adjust keys Turn clockwise to switch the radio power on, when the radio is turned on, rotate clockwise to increased volume, counter- clockwise to decrease the volume. Turn counterclockwise fully to switch the radio off.
④ Speaker ⑤ Microphone ⑥ PTT Key Press and hold down the PTT key then speak into the microphone to transmit. ⑦ Button 1 Press to activate the programmable function. (The detailed consult to basic operation) ⑧ Button 2 Press to activate the programmable function. (The detailed consult to basic operation) ⑨ MIC-SP Jack Connect to optional speaker/MIC and programming cable. Basic Operation Turning the power on /off Rotate the power switch/volume adjusting keys clockwise to turn the power on.
Adjusting the volume After the radio is power on, you can rotate the power switch/volume adjust keys to adjust the volume level, rotate the knob clockwise to increase the volume, or rotate the knob anti-clockwise to decrease the volume. Selecting a Channel Turn the channel selector knob to select channel 1 to 16, rotate the knob clockwise to increase the channel number, or rotate the knob anti-clockwise to decrease the channel number.
1.) Group Call If you want to transmit a group call, the radio must be set with group call contact and preset a group call contact for current digital channel, press PTT key to transmit a group call. Or you can set the One Touch Call key as group call feature, then press programmed key to transmit a group call. Release PTT key to receive. 2.
●Unassigned:The ●One key is not assigned with any function. Touch Call 1~6:Allow user to initiate digital group call, digital private call, or send preset message or send call alert via the one touch call function. ●Emergency on/off: Allow user to make an emergency call. ●Monitor:Enable ●Scan ● monitor function. on/off: Allow user to enable or disable the scan function. All alert tone on/off: Allow user to enable or disable all alert tones.
activate the VOX feature a VOX on sounds; disable the VOX feature a VOX off sounds. Note: Plug the dedicated earpiece into the accessory jack of the radio, the VOX feature is effective. ●Nuisance Delete: While scanning on, If you don’t want to receive activities on the channel, press the programmed Nuisance Delete key to remove the channel from the scan list temporarily. When restart scanning, the nuisance channel will return to scan list.
analog channel to select scan list ● Scan Hang Time : When a signal is detected on a channel, scan pauses on that channel, the radio will remain on the busy channel until the signal is no longer present. When the signal “ drop out” the radio will remain on the channel momentarily before scan resumes. The delay time is programmed 500 to 10000 milliseconds.
channel activities and receive weak signals. Press the programmed Monitor key to activate the monitor function, if a signal is detected, until the signal is no longer present the radio will exit monitor mode. Permanent Monitor: Permanent monitor feature is the same as monitor, but long press the Permanent Monitor key to enter monitor mode, the radio will remain on monitor mode until long press it again to exit. Message On digital channel, you can send preset messages by programmed one touch call key.
type select short message, message text select from preset message list. Then the programmed key set as one touch call, press the programmed key to send a message to a group call. ● Private Call On one touch call menu, the call member select private call contact, and the call type select private call. Then the programmed key set as one touch call, press the programmed key a high-pitched tone sound, with 5 seconds press PTT key to transmit a private call.
around” sound; switch to repeater mode, a “repeater” sounds. Via programmable software to set it: Channel folder → Zone → a digital or analog channel → Allow Talk Around Note:To enable this function, TX frequency should be different from RX frequency, and the channel will set as allow talk around on the programming software. TX Power You can switch power levels to Low or High.
alarm, after send emergency information then press PTT key to exit emergency mode. Via programmable software to set it: Signaling Systems folder → Digital Red Alert → add system1 to set parameters → Channel folder → add Emergency system ● Emergency Type: Disable, Regular, Silent, Silent with voice, the Disable option is unable to transmit emergency information. ●Emergency Mode: Emergency Alarm, emergency alarm with call, emergency alarm with voice to follow.
Time out Timer (TOT) The purpose of TOT is to prevent any user occupy a channel for an extended period. If a channel is busy, the time will be shorter. If the preset time expires, the radio will generate beep and terminate transmission automatically. Via programming software, you can set TOT as 15-495 second.
transmitting when you stop talking with no need of PTT press. You may set VOX level as1~8 or disable (Off). When the environment too much noise, VOX level will be higher, when the environment is quiet, VOX level will be lower. It allow user to set VOX delay as 500 to 10000 milliseconds.
Voice Indication → Channel Free Indication → Talk Permit Indication Reject Stranger Call On digital mode, if enable reject strange call feature, while the call ID not exist in the contacts list, it’s unable to transmit or receive. When received group call or all call, the device ID of transmitter and group call ID or all call ID preset on address list.
Battery Saver This feature allows an idler radio to automatically enter battery saver mode, the mode will extend battery service life, but response time may be delayed. You can set battery saver time ratio as : 1:1、1:2、1:3、1:4, the time rate is smaller, the power saving more evidently.
Statement Our Company endeavors to achieve the accuracy and completeness of this manual, if you have any question, you can contact with us, we will make a detailed answer to you in time.