Notice to the user Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. Illegal operation is punishable by fine or imprisonment or both. THANK YOU We are grateful you choose BeiFeng series professional radio communications products! Since 1989, BeiFeng has been always engaging in research and exploration of radio communications technologies, In order to lead intelligent technologies in the industry.
FCC radiation exposure statement This radio is intended for use in occupational/controlled applications where users have been made aware of the potential risks for exposure and can exercise control over their exposure. This product is not authorised for general population, consumer or similar use. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
Cette radio a été conçue pour un usage professionnel dans un environnement contrôlé, où les utilisateurs sont pleinement conscients du danger potentiel de l’exposition à laquelle ils sont soumis et peuvent exercer un contrôle sur cette exposition. Ce dispositif radio N’EST PAS autorisé pour l’ensemble de la population, les consommateurs en général, ni pour une utilisation similaire. Cet émetteur ne doit pas être co-localisés ou fonctionner en conjonction avec une autre antenne ou émetteur.
◆Don’t leave the transceiver in direct sunlight for a long time, don’t place the transceiver on extremely heat, damp, dusty area, and don’t put it on unstable surfaces; ◆When restriction or warnings are posted regarding the use of radio devices, please obey the regulation turn the transceiver power off; ◆Use of the radio while you are driving may be against traffic laws, please prohibit using it ; ◆If you notice any problems on the radio, please turn off at first. Then contact with local dealer.
Zone ......................................................................................................................... 25 Messages ................................................................................................................ 25 Call Logs .................................................................................................................. 28 Settings ....................................................................................................................
Warranty Card 1 Certificate 1 Antenna Strap Charger Belt Clip Li-ion Battery Screws Installation of Accessories Installation/ removing the antenna Hold the supplied antenna by its base, then screw it into the connector on the top panel of the radio until fasten. Turn the antenna anti-clockwise to remove it.
Installation/ removing the belt clip Attach the belt clip using the two supplied3*4mm binding screws. Attaching/Removing the strap Thread the hand strap to the loop back of your two-way radio.
Attaching/Removing the Battery Warning! Don’t short-circuit the battery, it may cause the battery damaged or burst into flame; Never attempt to remove the casing from battery, that avoid to short the battery terminal; Battery is flammable objects, don’t throw it into fire or don’t use it on dangerous area. Match the guides of the battery with the corresponding grooves on the upper rear of the radio, then press the battery until a click is heard to lock it in place.
To remove the battery, please turn the power off then press the release latch to unlock the battery pull the battery away from the radio. Note: Don’t attach / remove the battery if the transceiver turned on. Li-ion battery features New batteries are activated from factory; please charge your battery before using it. The maximum battery capacity and performance is achieved after three full charge/ discharge cycles.
●Charge your battery about 50% before you store it for a long time, so that can prevent to decrease the battery performance. ●As the battery is charged and discharged repeatedly, the battery capacity decreases, even if the battery is unused, the battery degrades, store battery in a high temperature will shorten its lifecycle. Charging the Li-ion battery ● When the battery power runs low, the radio will send alert sounds, please recharge the battery.
4. The charger indicator glows green when the battery is fully charged. Note: Mack sure the battery is connected to the charger, but the charger indicator not glow, Maybe the battery /charger has damaged or temperature out of the limit. Attaching the Speaker/Microphone Open the accessory jack cover, then align the plug with the accessory jack and tighten the screw on the plug.
Getting Acquainted ① Power switch/volume adjust keys Turn clockwise to switch the radio power on, when the radio is turned on, rotate clockwise to increased volume, counter- clockwise to decrease the volume. Turn counterclockwise fully to switch the radio off. ② Channel Selector Knob Turn the knob to select channel 1-16. ③ LED Indicator 1. When transmitting LED glows red; 2. When receiving LED glows green; 3.
4. When scanning LED flashes orange. ④ MIC ⑤ Left key Press to move to the next step or store the setting. ⑥ MENU Press to enter menu mode, you can select the desired menu item. ⑦ Selection Key Press up or down/left or right to select the menu function item ⑧ Right key Press to move back to the previous menu. ⑨ HOME key Press to quickly return home screen. ⑩ Speaker 11 ○ Numerical To input numbers and letters 12 ○ MIC-SP-USB Jack Connect to optional speaker/MIC and USB programming cable.
operation) 15 ○ Button 2 Press to activate the programmable function.
Keypad Locked disable all tone alert Emergency on VOX on Plug in earphone Direct /Talk around Mode Monitoring Connect to Computer Battery Capacity Turning the power on /off Rotate the power switch/volume adjusting keys clockwise to turn the power on. Rotate the power switch/volume adjusting keys anti-clockwise to turn the power off.
Adjusting the volume After the radio is power on, you can rotate the power switch/volume adjust keys to adjust the volume level, rotate the knob clockwise to increase the volume, or rotate the knob anti-clockwise to decrease the volume.
private call contact, a group call contact or an all call contact; To transmit press and hold down the PTT key, LED indication glows red, speak into the microphone, hold the palm microphone approximately 3 to 4 centimeters away from your mouth. Note: While enable talk permit indication feature, if the channel available, press PTT key to transmit will with a tone.
Group Call (1) If you preset a group call contact for current digital channel. Press PTT key to transmit a group call; (2) Enter Contacts menu to select the group call number you want to call, then press PTT key to transmit a group call; (3) Enter Call Log menu to select the group call number you want to call, then press PTT key to transmit a group call; (4) You can set the One Touch Call key as group call feature, then press programmed key to transmit a group call.
private call within the preset time period, the radio will display the missed call icon; while a group call is received, you may press the PTT key within the preset time period to call back. If you do not respond to a received group call within the preset time period, the radio will display the missed call icon; while an all call is received, you can’t respond to an all call. Note: While enable channel free indication feature, if the transmitter release PTT key will with a tone.
●Keypad Lock: Allows you to enable the keypad lock feature, if it is enabled you can’t operate keys except PTT key and side button. Press MENU and # key to unlock. ●Scan ●All on/off: Allow user to enable or disable the scan function. alert tone on/off: Allow user to enable or disable all alert tones. ●Battery ● Short Indication:It’s convenient to know battery capacity Massage: This function will convenient to enter message function menu.
the channel, press the programmed Nuisance Delete key to remove the channel from the scan list temporarily to delete nuisance channel temporary. ●Permanent Monitor: Permanent monitor feature is the same as monitor, but permanent monitor feature only can be set as long press key. And you should long press the programmed Permanent Monitor key to exit this function. Note: ●You can assign any of the functions to a short or long programmable key-press.
While select a contact as private call ,the screen displays as following, a private call can view its detail、send call alert 、send message、edit name or number 、delete、 send device check、disable or enable、send remote monitor. ●Call Alert: Call alert is used for prompting the private receiver; ask them respond to transmitter if communication is available. While receiving call alert command the radio will generate alert tone.
via menu. If the device is lost or stolen, a user can use this function to disable the device. However, this device will continue monitoring air interface to receive its "Device Enable" command. ●Edit: Modify the number or name of a private call contact. Press”*” key to delete, press “#” to switch input method, the available number range is 1~16776415, name input 16 characters at most.
delete, press “#” to switch input method, name input 16 characters at most; then input number, the available number range is 1~16776415. After add a private call contact successfully, on contacts list will show new contact. Scan 1. Scan On/Off While current channel add scan list and the list contain 2 channels at least, you may enable the feature. Scanning allows the device to search the scan list connected to the current channel to locate qualified channel for receiving or voicing.
the channel will enter scanning automatically; While button 1 or 2 programmed as Scan on/off, press it to enable scan feature. 2. View/Edit List Allow a user to view/edit the scan list via menu, "View Member" allows a user to view the scan member, deleting a member from the scan list; Add Member allow a user to add a new member to the scan list, the list contain 16 channels at most. It is not allowed to create a new scan list or delete existing scan lists from the device.
You can edit desired text message(140 characters at most) and send it to an private call contact or group call contact, when editing a message, press “# ”key for switching input method, press “ * ” key for deletion and modification, press left or right key to switch input cursor. For non-numeric input method, key “ 1 ” is a symbol key. Key “ 0 ” is a space key. After the message is edited, you can select a contact from the address list which the message is sent to or manually dial a number to send to. 2.
Note: Preset text messages also can assign to one touch call, and press the programmed key to send messages. 4. Outbox Enter outbox menu, you can view the message is sent successfully or failed, outbox can save up 30 sent messages. If sent message is successful displays you can choose to forward or delete it; If sent message is failed displays ,you can choose to resend、forward or delete. 5.
Call Logs 1. Missed Call The missed calls list can save up to 10 entries, when the memory for call logs is full, the oldest entry will be deleted automatically. You can add it to contact list or delete it. 2. Answered Calls The answered calls list can save up to 10 entries, when the memory for call logs is full, the oldest entry will be deleted automatically. You can add it to contact list or delete it. 3.
4. Clear Record This function is convenient to delete Missed call logs Answered or Dialed call logs, Clear All will delete all call logs at the same time. Settings 1. Settings Allow a user to perform basic settings for the two-way radio. ●Talk Around: When your repeater malfunctions, or when radio is out of repeater’s range, you can continue to communicate in talk around mode. While enable talk around feature, the screen displays: ,By this time TX frequency the same as to RX frequency.
Note:To enable this function, TX frequency should be different from RX frequency, and the channel will set as allow talk around on the programming software. ●Tone/Alerts: To set tones for your radio, tone alerts include settings of all tones, call alert tone, message tone, keypad tone. If disable all tones, all alerts will be off except emergency tone. ●TX Power : Allow a user to change the power level, there are two levels available: high ( indicated by H) and lower(indicated by L).
Intro screen is enabled, while the radio power on, the screen display BF Logo and device name; While the Intro screen is disable ,the screen only displays device name . ●Keypad Lock: Allow a user to enable or disable keypad lock via menu. While Keypad locked indicate: , that you can’t operate the keypad except PTT key and button 1 or button 2. Press “MENU” and” #” key to unlock. ●LED indicator: To set whether to enable LED indication via menu.
Note: The VOX feature only is used if you are using a supported headphone. ● Power-on Password: If enable power-on password feature via programming software, you can modify the password by this menu. First you need input old password correctly, then input a new password twice the same, that will modify the password successfully. Note: This menu is effective if power on password is set via programming software. ●Language: The radio supports two languages: Chinese and English. 2.
●My Number: Allow a user to view the radio ID number, which is same as device ID. ●Firmware ●CP version: View firmware version information. Version: To view CP version information. Digital Emergency In case of an emergency you can enter emergency mode to ask for help, for each emergency mode, there are three emergency types and three emergency mode available.
Silent: In emergency mode, the radio won’t give any audible or visible indication; Silent with Voice: In emergency mode, the radio won’t give any audible or visible indication, but will receive voice. Emergency Mode: Alarm: In this mode, you can send alarm information, while receive ACK or reach the maximum retries will exit emergency mode. Alarm with Call: You can press programmed” Emergency On/Off” key to send emergency information, then press PTT to transmit an emergency call.
the emergency mode automatically. And long press the programmed emergency key to exit the emergency mode; If choose silent or silent with voice type, press PTT key or long press programmed emergency key to exit the emergency mode. 3. Receive Emergency Information When the feature” emergency alarm indication” is enable, if received emergency information, the radio displays icon , the transmitter’s ID and name, an alarm tone will sound. To exit the emergency mode, long press the programmed emergency key.
TX Permission Digital Channel This feature can restrict the channel if it is already in use you will be unable to transmit. There are three options available: always, color code free, channel free, if choose always, whenever press PTT key to transmit directly; If choose color code free, you will be unable to transmit on the channel if the color code is already in use; If choose channel free, you will be unable to transmit on the channel if it is already in use.
will turn off automatically while battery is too low. Via programmable software to set it: General Setting folder→RX low battery internal CTCSS Standard Frequency Table CTCSS Fre. CTCSS Fre. CTCSS Fre. CTCSS Fre. No. [Hz] No. [Hz] No. [Hz] No. [Hz] 1 67.0 11 94.8 21 131.8 31 186.
2 69.3 12 97.4 22 136.5 32 192.8 3 71.9 13 100.0 23 141.3 33 203.5 4 74.4 14 103.5 24 146.2 34 210.7 5 77.0 15 107.2 25 151.4 35 218.1 6 79.7 16 110.9 26 156.7 36 225.7 7 82.5 17 114.8 27 162.2 37 233.6 8 85.4 18 118.8 28 167.9 38 241.8 9 88.5 19 123.0 29 173.8 39 250.3 10 91.5 20 127.3 30 179.
9 D054N D054I 37 D261N D261I 65 D546N D546I 10 D065N D065I 38 D263N D263I 66 D565N D565I 11 D071N D071I 39 D265N D265I 67 D606N D606I 12 D072N D072I 40 D271N D271I 68 D612N D612I 13 D073N D073I 41 D306N D306I 69 D624N D624I 14 D074N D074I 42 D311N D311I 70 D627N D627I 15 D114N D114I 43 D315N D315I 71 D631N D631I 16 D115N D115I 44 D331N D331I 72 D632N D632I 17 D116N D116I 45 D343N D343I 73 D654N D654I 18 D125N D125I 46 D346N
Statement Our Company endeavors to achieve the accuracy and completeness of this manual, if you have any question, you can contact with us, we will make a detailed answer to you in time. All the above specifications and design are subject to change without prior notice due to continuous development.