User's Manual

ManualsBrandsFujian BelFone Communications Technology ManualsElectronicsDigital Radio

Notice

Government law prohibits the operation of unlicensed radio transmitters within the territories

under government control.

Illegal operation is punishable by fine or imprisonment or both.

Acknowledgement

We are grateful you choose BeiFeng series professional radio communications products!

Since 1989, BeiFeng has been always engaging in research and exploration of radio

communications technologies, In order to lead intelligent technologies in the industry. We still

make every effort to research and design products according to modern complicated

communications environment, and We offer complete and customized communication solutions to

clients. our products will satisfy you because of its excellent performance and outstanding

communications strength . No matter what field you are in. You will be Satisfied with the radio .

This manual is applicable to UHF digital FM transceiver model: BF-TD5033

Warning！

Precautions

It’s important that the operator is aware of and understands hazards common to the operation of

any radio .Please observe the following safety precautions to prevent radio damage or personal

injury. The following precautions shall be observed during operation 、service and repair of this

radio.

The recommended usage rate is 1 minute for TX and 4 minutes for RX,When the radio is used for

transmission for many hours Continuously, the

radiator and chassis will become hot, allow the rear

panel of the two-way radio to contact surface of low melting point /low Ignition Point object.

Don’t leave the transceiver in direct sunlight for a long time , Don’t place the transceiver on

extremely heat、damp、dusty area, and don’t put it on unstable surfaces.

◆ devices, Please obey the regulation turn the transceiver power off. )

◆ Use of the radio while you are driving may be against traffic laws, Please prohibite using it .

◆If you notice any problems on the radio, please turn off at first. Then contact with local dealer.

Do not modify this radio unless instructed by this manual or refer service to a qualified licensed or

certified technician only.

◆ If you want to use the machine for secondary development, Please cantact with BeiFeng’s

Technical engineer or dealer for technical assistance.

◆ Please keep the surface of radio is clean and dry, Clean the radio using a cloth moistened with

clean water and a mild dishwashing liquid.

Always switch the radio power off before installing optional accessories.

Contents

Supplied accessories 2

Accessory 2

Installation of Accessories 3

Installation/ Removing the antenna 3

In explosive atmospheres(inflammable gas,dust particles,much

powder

area，etc.

),Please turn the power off.

Summary of content (26 pages)

PAGE 1
Notice Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. Illegal operation is punishable by fine or imprisonment or both. Acknowledgement We are grateful you choose BeiFeng series professional radio communications products! Since 1989, BeiFeng has been always engaging in research and exploration of radio communications technologies, In order to lead intelligent technologies in the industry.
PAGE 2
Attaching/Removing the Battery Li-ion battery features Charging the Li-ion battery Attaching/Removing the belt clip Attaching/Removing the strap Attaching the Speaker/Microphone About the radio Basic Operation LCD Icons Turning the power on /Turn off Adjusting the volume Selecting a Channel Transmitting Receiving Button setting Functions and Operations Digital Channel Contacts Scan Zone select Messages Call Log Radio Settings Radio Info Analog Channel CTCSS Standard frequency table CDCSS standard code table
PAGE 3
strap BF-RL801 1 belt clip BF-BS103 1 charger BF-B33 1 Li-ion battery BF-A33 instruction manual warranty card certificate 1 1 1 1 Antenna Strap Belt Clip Charger Li-ion Battery 3
PAGE 4
Instruction Manual installation of Accessories Installation/ Removing the antenna Hold the suppied antenna by its base ,then screw it into the connector on the top panel of the radio until fasten. Turn the antenna anti-clockwise to remove it.
PAGE 5
Match the guides of the battery with the corresponding grooves on the upper rear of the radio, then press the battery until a click is heard to lock it in place. To remove the battery , Please turn the power off, then press the release latch to unlock the battery pull the battery away from the radio. Note: Don’t Attach / Remove the Battery if the transceiver turned on . Li-ion battery features ●New batteries are activated from factory, Please charge your battery before using it .
PAGE 6
Please remove the battery timely when the battery is fully charged. Notes: While the battery is charged ,the ambient temperature must be within 0~40, Temperature out of the limit may reduce working life or Charging efficiency. charging steps 1.Place the battery or the radio is attached with a battery in the charger. 2.Plug the AC connector of the switching power into the outlet socket. 3.
PAGE 7
LED Indicator When transmitting LED glows red. When receiving LED glows green. When powering on LED flash turns orange. When scaning LED flashes orange. Power /Volume Power switch/volume adjust keys Turn clockwise to switch the radio power on, When the radio is turned on, rotate Clockwise to increased volume, counter clockwise to decrease the volume.Turn counterclockwise fully to switch the radio off. Channel Selection Knob Turn the knob to select channel 1-16. Orange keys This key is a programmable button.
PAGE 8
Press to enter menu mode, you can select the desired menu item. Right key Turn back to the previous menu. Home key Press quickly return to home screen. PTT key Press and hold down the PTT key then speak into the microphone to transmit. 11 Button 1 ○ Programmable button.( the Detailed consult to Basci operation ) 12 Button 2 ○ Press to activate the programmable function .( the Detailed consult to Basci operation ) 1○ 3 MIC-SP-USB jack Connect to optional speaker/Mic and USB programming cable.
PAGE 9
VOX on Plug in headphone Direct /talkaround mode Duplex mode on Monitor Linked Computer Battrty Capaticy Green: means the battery is sufficient green : Yellow :battery capacity is medium，Red: Low battery Turning the power on /Turn off Rotate the Power switch/volume adjust keys clockwise to turn the power on .。 Rotate the Power switch/volume adjust keys anti-clockwise to turn the power off .
PAGE 10
incoming calls. CTCSS/CDCSS may set by your local distributor. When the channel is set with CTCSS/CDCSS, the user can only receive the calls on the same channel with same CTCSS/CDCSS. Button setting For enhanced convenience, you may program the keys SK1, SK2, SK3, short and Long press of a key can be assigned with different functions. Programmable keys are including functions listed below: ●Unassigned：this key is not assigned with any function.
PAGE 11
While the radio working on analogy mode, Programmable keys can be programmed to those functions list: Unassigned、monitor、backlight automatic on/off、keypad lock、scan on/off、all alert tone on/off、zone selection、high/low power、repeater/talkaround、VOX on/off Functions and Operations Digital channel Contacts Press the MENU to access the contact list,On the contacts ,you can search address list members,add new contacts,manual dial .
PAGE 12
Note: while the contacts item add in the default address or one touch call ,That you will unable to delect the item。 Extend Function Call Alert: Allow user to transmit a call alert through the menu . Call Alert is used for prompting the receiver, ask them respond to transmitter if communication is available. The user can receive alert tone Only when a channel is available. On digital mode, a radio only transmit call alert to the other.
PAGE 13
While you want to transmit a group Call through Contact List ,The screen display as following: View number : used to view group ID number of a contact in the address list. （）All call While you want to transmit a all Call through Contact List ,The screen display as following : View number : used to view all call ID number of a contact in the address list. 4.New contact You can add a Private Call contact to the contact list.
PAGE 14
This function convenient to user dial to linkman while it don't store in the address list . Allow user input the Private Call ID number through the number key,After you input the ID number ,then press PTT key to transmit.Or press key to select call alert ,device check, remote monitor ,device enable ,device disable to operate. ②Scan ●Scan on /off Allow user to enable or disable scan function for the current channel via menu.
PAGE 15
④Messages ●Inbox Inbox can store up to 50 messages, In inbox, press key to view messages, where you can reply to a message, forward or delete a message. After reading the message ,behind the message will diplay : , behind the unread message will diplay : . ●Write SMS Edit a new message (up to 140 characters) to send it to an individual or group. When editing a message in the write box, press for switching input method,press key is a symbol key.
PAGE 16
Note：While editing the message ，press * key to modify， and press switching input method,press is a symbol key. Key key for key to switch input cursor. For non-numeric input method, key is a space key. ●Outbox Outbox can store up to 20 messages,On outbox press key to view the and press this key again to re-send , edit ,forward or delete the sent message.Message send successful will display ,Message send failed will display: .
PAGE 17
●Answered Allow a user to view last 20 Answered call logs. This log also can be a shortcut for a user to originate a call. A user can access answered call log via menu, and press answered call log and Press PTT to transmit . or press key to view key again to store the answered item into the address list or directly deleted . ●Dialed Allow a user to view last 20 Dialed call logs. This log also can be a shortcut for a user to originate a call.
PAGE 18
alert tone and Message tones can select tone 1to10 or disable it to select no style. TX Power : Allow a user to select high/low TX Power via menu.High Power display with H,Low power display with L. elete ere are more than 2 zones ● Backlight: allow a user to change backlight setting via menu.You can select Auto or Turn on , while you select automatic on ,the light will become dark after 5s you don't operate the key,And the light will keep on all the time when the backlight turn on.
PAGE 19
●LED indicator: To set whether to enable LED indication via menu.While disable all indicator , the screen becomes dark and Tx red indicator, Rx green indicator ,scan orange indicator are off. Please use this function with due care. ●Allow a user set radio in talkaround mode via menu.
PAGE 20
⑧Radio Info This function allow a user to view related device information. ●My number: allow a user to view the radio ID number, which is same as device ID. Firmware version: view firmware version information. Battery capacity: To view the radio’s remain battery capacity.It’s convenient for user to know battery capacity and charge the battery in time.
PAGE 21
Squelch:on the analog mode,allow user to set squelch level .When you are receiving while the squelch function is on weak signals may become intermittent.The function can filter out background noise.You can set SQL1~9, Level 3 is set to its basic setting . CTCSS Standard frequency table QT No. [Hz] QT No. [Hz] QT No. [Hz] QT No. [Hz] 1 67.0 11 94.8 21 131.8 31 186.2 2 6 3 7 4 8 69.3 79.7 71.9 82.5 74.4 85.4 12 16 13 17 14 18 97.4 110.9 100.0 114.8 103.5 118.8 22 26 23 27 24 28 136.
PAGE 22
10 91.5 20 127.3 30 179.
PAGE 23
Statement Our Company endeavors to achieve the accuracy and completeness of this manual, If you have any question, you can contact with us , We will make a detailed answer to you in time. All the above specifications and design are subject to change without prior notice due to continuous development.
PAGE 24
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 25
To control your exposure and ensure compliance with the occupational/controlled environment exposure limits always adhere to the following procedures. Guidelines: • Do not remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. • Do not use this device if the operational requirements described herein are not met. Operating Instructions: • Transmit no more than the rated duty factor of 50% of the time.
PAGE 26
EU Regulatory Conformance As certified by the qualified laboratory, the product is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC. Please note that the above information is applicable to EU countries only.