Acknowledgments! mobile Thank you f or buying tw o-way radios manufactured by BEIFENG TELECOM for communication, which are believed to be capable of providing you with convenient and reliable communication and producing the best possible results. BEIFENG TELECOM two-way radios adopt advanced technologies and it is believed that quality and function of the product will make you satisfied.
If un usual odor or sm oke is se nsed fro m the product, please cut the p ower so urce off immediately, and then remove the battery pack or battery case fro m the product. After this, contact local BEIFENG TELECOM vendors for information. Unpacking and Inspection Note: fol lowing unpacking des criptions are o nly for BEIFE NG TELECOM vendors, authorized B EIFENG TELECOM service centers or factories. Please caref ully take t he product out of the package.
Preparation Warnings: Do not make the battery cell overcharged! If ch arging for the b attery p ack is no t c ompleted i n a s pecified t ime, pleas e sto p charging; otherwise, the battery pack may be overheated, cracked or on fire. Do not put the battery pack into a microwave oven and high-pressure container! Otherwise, the battery pack may be overheated, cracked or on fire.
Charging After the charger is energized, t he c harger i ndicator lights green. Install t he battery pa ck, contact pro perly, an d th en the re d i ndicator is o n t o st art ch arging. After the b attery is fully charged, the green i ndicator is on. If t he temperature is beyond the allowable range during charging, the red indi cator flashes; if t he batt ery is dam aged or po orly con tacted, the re d indicator flashes.
About the product ① Power /Volume Power switch － V olume controller 1. 2. Rotate it clockwise to power on. Rotate the knob to adjust the volume. If being configured to cancel all mute modes, the two-way radio will broadcast channel number in a voice m anner. If the cha nnel transmits no frequency, you will b e prompted with a short message prompt instead of voice. Rotate the knob to the end counterclockwise to switch the power off. ② Channel selector 1.
Return to the previous operation □ OK key Confirmation key □ Left key Move to the left side □ Right key Move to the right side Basic Operations Power ON/OFF Rotate Power switch/Volume controller clockwise to switch the power ON. Rotate Power switch/Volume controller counterclockwise to switch the power OFF. Adjust volume Rotate Power switch/V olume control ler to reg ulate the volume. Rotate i t cl ockwise t o increase t he v olume, i.e. t he vo lume status bar sh owing full .
two-way radio will not display any information when receiving the emergency alarm. Emergency call pr ompt: check if t he tw o-way ra dio se nds video i ndication aft er a n emergency call is received. Functions Settings 2.
1) Device name Device Name: enable a user to name the two-way radio he or she uses, such as BF-DH200. Set an alias for the two-way radio. When turning it on, it displays welcome message. A user can input up to 8 characters at most. Valid charact ers include alphanum eric c haracteristics, space and special charac ters. Both Chinese and English are supported. 2）Device ID Set a unique ID for the two-way radio.
The v alid se t bit for device ID cont ains 8 di gits. D ecoding is p ossible w hen device ID matches calling ID of a private call (RX). Each de vice shall have a unique ID t o di al the num ber of the other party when re alizing point-to-point communication (including private call and SMS), such as 1, 2, ......, 16776415. 3) Repeater ID The valid set bit for R epeater ID contai ns 8 digits. Decoding is possible when Repeater ID matches repeater system ID (TX).
GPS is used by the control center to keep track of locations of system members to arrange them scientifically. The model provides optional GPS. For details, consult with your local vendor. 8) Duration of TX Preamble (ms) Preamble i s a b it stri ng ad ded b efore d ata m essage or c ontrol message (te xt m essage transfer, p osition m essage transfer , reg istry, tw o-way radio detection, si ngle-call, etc) before transmission.
If this feature is enabled, an unoccupied two way radio will automatically enter the battery save mode, i. e. making c ertain fe atures in st andby mode. A fter a certain t ime or when a user presses any key , th e tw o-way radio ret urns n ormal operati on an d ch ecks if an y incoming call in th e ch annel.
The t wo-way radio s ounds t his prompt t one a fter t he P TT key i s pressed. After t his, t he two-way radio can tran smit it in th e channel. The purpose is to prompt a user with successful connection for communication. Null and digital modes are available. 4）RX battery low prompt interval (s) When th e two-way rad io receiv es a call or is uno ccupied, i f it reach es th e b attery lo w threshold, you w ill hear a battery lo w prompt to ne.
monitor function to monitor the channel. In digital mode, a user can only check if there is any activity before transmission. If yes, the two-way radio will transmit the voice, but not to ongoing actual voice or data communication. f) Permanent monitor: it has the same function as that of monitor (only for a handset), i.e. allowing a user to monitor the channel to ensure that there is no activity before transmission.
Enable a user to change short press of key 1. It has the same function as above. 4）Long press of key 1 Enable a user to change long press of key 1. It has the same function as above. 5）Short press of key 2 Enable a user to change short press of key 2. It has the same function as above. 6）Long press of key 2 Enable a user to change long press of key 2. It has the same function as above. Short press of key 3 Enable a user to change short press of key 3. It has the same function as above.
2. Call type Enable a user to select a call type from selected call members in the “call object” list. 3. SMS If “SMS” is selected, a user can select SMS content from the “SMS” list. 5. SMS Function Enable a user to select quick SMS. These SMS are selected from SMS setting. A user can input up to 140 characters. Valid characters include alphanumeric characters, space and special characters. A user can send SMS by setting short press or long press of programmable key (SMS) or accessing the menu.
Menu Suspension Time Set the time the two-way radio keeps in menu mode. After this, the two-way radio returns to main screen. If this time is set to “0”, the two-way radio always keeps in this mode which is its built-in feature. The time ranges from 0- 30 s with step 1s. SMS Enable a user to access “SMS” feature via menu or key. A user can check inbox, edit SMS, and send SMS or quick SMS. 7. Address Book One、Call Prompt Enable a user to send a call prom pt via menu.
communication is available. A call prom pt can be received only when a channel is available. In digital mode, a user can only send out a call prompt to a single two-way radio. Two、Edit Enable a user to edit alphanum eric ch aracters on the screen. A user can add items to the contact list and edit existing items in the contact list. new Three、Manual Dialing Enable a user to access “M anual Dialing” function via menu.
8. Scan a、Scan ON/OFF Allow a user to enable or disable scan feat ure for the current channel via m enu. This feature allows the two-way radi o to search the scan list connected to the current channel to find available channels for receiving or voicing. b、Edit List Enable a user to edit the scan list via menu.
Enable a u ser to set the two-way rad io in talk-aro und m ode via menu or key s. (The co mmunication obje ct shall be used within the co mmunication distanc e without use of a repeater). Scope of Applications 1）Communicate with the other party for a long time to prevent making the repeater busy t o in vite the ot her part y f or comm on-frequency co mmunication in talk-around mode. 2）Communicate beyond the effective coverage area of the repeater.
1）Device remote destroy decoding: If this feature is checked, the two-way radio with the function of remote destroy or activ ation can be remotely destroyed or activated. TX and R X are disabled for a remotely destroyed two-way radio. The purpose is that if the two-way radio is lost, remotely destroy it to disable TX and RX functions to prevent information leakage. 2）Remote monitor decoding: If t his feat ure is ch ecked, t he t wo-way radio with t he f unction of remote monitor can realize remote monitor.
Alarm Type An alarm is a non-voice signal capable of triggering prompt or indication to the other two-way radio. This feature is to specify the alarm behavior of the two-way radio when a user presses the emergency alarm key. 1) 2) 3) 4) Disable: the two-way radio is disabled for transmitting an alarm signal. General: The two-way radio sends an alarm signal a nd provides audio indication that it is in emergency mode.
activity in the current channel. The two-way radio will try impolite transmission several times to obt ain confirmation and then try polite transmission several times. This feature is to set number of times trying impolite transmission of an emergency alarm. (1-15 times) Polite retry Polite transmission refers to transmi ssion performed w hen there is no activity in the current channel.
2、Select “Add (A) ->Group Call (G)(ID: ********)/Private Call (P) (ID: ********)/All Call (ID:16777215)/Repeater Call (R) (ID: ********)”. 3、Right click a call m ember and select Rename (M) to assign a unique name for the call. Valid characters include alphanumeric characters, space and special characters. A name cannot be a null character. RX group list The purpose of setting a RX group list is to realize inter -group calls.
1）Add area 1. Right click “Channel” folder in the view. 2. Select “Add (A)”. 3. Assign a unique name for the area. 2）Add a channel in an area 1.Right click an area. 2.Select “Add (A)” to create a digital (channel 1). 3.Assign a unique name for the channel. 3）Delete area 1.Right click “Area” folder in the view. 2.Select “Delete (D)”. 3.The area is deleted. 4）Delete an channel in an area 1.Right click a specific channel in the view. 2.Select “Delete (D)”. 3. The channel is deleted.
1）Scan List Link the sc an lis t to th e channel. All m embers will be sc anned in th e lis t during scanning. A use r can select any available scan list (including auto scan). If the channel scans no scan list, pressing the scan switch will prompt a user with an invalid key tone. 2) Auto scan Enable a tw o-way radio to start auto scan when a user selects th e current channel.
working in repeater mode. Thus, A digital repeater channel can be frequency and s et tim e slot are completely described only when set simultaneously specified. The intercom munication two-way radios or groups should have the same frequency and time slot. Notes: This feature applies only in repeater mode. Regardless of the time slot being monitored in repeater m ode, i.e. time slot 1 or 2, the two-way radio will always monitor two-way radio s transmitting in talkaround mode.
Add offset to RX frequency to obtain TX frequency. 11）Reference frequency Down offset for RX and TX frequency difference. 12）Rx group list Select group call communication available for the current channel. 13）Default communication address A call initiated in the channel when pressing PTT key. If “null” is selected, it will stop initiating a call in the channel and prompt a user with an invalid call prompt tone.
TX timeout timer (TOT) is the time the two-way radio continues transmission before transmission automatically ends. This feature can ensure that a channel will not be exclusively occupied by any one of two-way radios. For a busy channel, a user can set shorter TX timeout. It ranges from 15 to 495 s. 17）TOT key update delay (s) Set the time after the TX TOT fails (which will terminal two-way radio TX) and before a user is allowed for transmission again the two-way radio waits in the channel.
2、Under “Device N ame”, set infor mation to be di splayed during start-up. V alid characters include alph anumeric characte rs, s pace and specia l characters. A name cannot be a null character. 3、Left clic k the tree view "Menu Def inition" to enter "M enu Def inition” editin g interface. 4、Check “Startup In terface” at the bottom of the “Setting” operation under “Menu Definition”. Notes: 1.
Settings Battery state Talkaround ON Manual Setting of ON and OFF of Startup Interface 1、Click “MENU” key to access the function list. 2、Press left and right “—” key to select “Setting” to enter “Setting” interface. 3、Press left and right “—” key to select “Two-way Radio Setting” option and press “OK” to confirm it. 4、Press left and right “—” key to select “Startup Interface” and press “OK” key to confirm it. 5、Press left and right “—” key to select “ON” or “OFF” to open or close the startup interface.
Setting Display Description Call 1 The first call set for the two-way radio Number New contact A call ID responding to Display a 1-8 digits call* number Establish a new call Able to set a new private call or group call Input a number Input and store name of a Input a random group of new call ID numbers from 1 to 16776415 Input a name Manual Dialing Input and store name of a Input random letters, new contact numbers or texts Input device ID to be called directly on the display Two-way
characters, space and special characters. A name cannot be a null character . P ress “OK” key to select the “Ring Tone” for the new contact. 6、Select tone: unselected ring tone, tone 1-10 Manual Dialing Setting 1、Click “MENU” key to access the function list. 2、Select “Address Book” and press “OK” key to enter “Address Book” option. 3、Press “—” to select “Manual Dialing” function and press “OK” key to enter “Manual Dialing” editing interface.
This scan group will be scanned in Priority 2 the second priority Priority OFF Disable scan priority for scan groups Scan group 1 (channel 1) Edit channel 1 in scan group 1 Edit channel priority in the scan list Editing priority Delete channels in the scan list Delete Scan setting Settings for programming software Left click “Menu Definition” to check “Scan ON/OFF” and “Editing List” options under “Scan”, and then select “Scan Group” in the “Scan List” on the “Channel” editin g interface.
“OK” key to confirm it. 4、Select “Edit Priority” and press “OK” key to confirm it. 5、Press “—” key to select “Priority: 1” and press “OK” key to confirm it. Then the priority of channel 1 is “OFF” and the priority of channel 2 is “1”. 6、Repeat above steps to set the priority of channel 1 and select channel 1 “Priority: 2”. Note: “Scan Group *” of the channel shall be preset in the programming software. The scan list of the scan group can be se t only when the two-radio switches to the channel.
channel. 5、Press “—” key to select “Yes” or “No” and press “OK” key to confirm it. Area Display Description * Area* Area* saved A preset area in the two-way radio A channel in the current setting area* that can be used by the two-way radio “Area” switching 1、Click “Key Function” option. 2、Select any one of key definitions from four programmable key definitions, drop down the function menu and select “Area Selection” key .
SMS Display Description Inbox View received SMS New Edit and send SMS Preset SMS preset in the two-way radio sent SMS Sent Record Delete all Delete all received or sent SMS Manually edit and send SMS 1、Click “MENU” key to access the function list. 2、Press left and right “—” key to select “SMS” option. 3、Press "OK" key to enter “SMS” editing interface. 4、A、Press left and right “—” to select “Inbox” B、Press “OK” key to view received SMS. 5、A、Press left and right “—” key to select “New”.
Received calls Display received calls from the calling party Outgoing calls A call initiated by the two-way radio FFFFFFF none Settings for programming software 1、Left click “Menu Definition” in the tree view. 2、Check “Missed”, “Answered” and “Outgoing” under “Call Log” 3、Write setting information to the two-way radio. Note: to check included options of “Call Log”, viewing of call log will be prohibited in the two-way radio.
Chinese/English are available Language selection Information about two-way radio Battery status (%) Display current remaining battery capacity percentage. Your number Display your device ID and group ID Firmware version CP version Communication mode setting for programming software 1、Left click “Channel” option. 2、Left click to select area channel and enter channel editing interface. 3、On the channel editing interface, set the frequency of the two-way radio to RX and TX pilot frequency.
5、Press left and right “—” key to select “Talk-around” or “Repeater mode: 2” and press “OK” to confirm it. High/low power setting Settings for programming software In the “Channel Editing” interface, under TX section – “TX power”, drop down “High” and “Low” options to preset high/low TX power for the two-way radio. Manually set the two-way radio 1、Enter “Two-way radio setting” option. 2、Press left and right “—” key to select “TX power” and press “OK” key to confirm it.
3、Set the remote destroy and allow private call only (0******), and remotely destroy a two-way radio in proper order. 4、Left click “Menu Definition” in the tree view and under the “Address Book” on the menu editing interface, check "Monitor", “Remote Destroy” an d “Activation”. 5、Write setting information into the two-way radio through the programming software.
should meet the req uirements set forth in the above standards before t hey can be marketed in the U.S, and t he manufacturer shall post a RF la bel on t he pro duct to inform users of oper ational instructions, so as to enhance their occupational health against exposure to RF energy. FCC Statement This equipment has been tested and found to comply with the limits for a C lass B digital device, pursuant to part 15 of FC C Rul es.
Instructions To control you r ex posure an d en sure comp liance with the occu pational/controlled en vironment exposure limits always adhere to the following procedures. Guidelines: • Do not remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. • Do not use this device if the operational requirements described herein are not met. Operating Instructions: • Transmit no more than t he rated duty factor of 50% of the time.
