User's Manual

ManualsBrandsFujian Baldr Technology ManualsElectronicsWater Timer

ITV0103W

WIFI IRRIGATION

WATER CONTROLLER SYSTEM

USER MANUAL

100*120mm

Manual Production Overview Main Function

Illustrated Operating Instructions

Up to 60 meters depending obstacles between gateway and tap timer

10.Tap-to-Run & Automation Irrigation

11.Tips

12.Warranty & Warning

13.Basic Parameters of the device

Downloading the App

Rainpoint

After finishing setting, icons will be found under Tap-to-Run and

Automation. The button on the right can enable or disenable the

Automation plan. The Tap-to-Run function connects different plans

and devices at the same time to enable “One-Click Management”.

1. Connection and Basic Information

2. Manual Operation

Manual mode: Click the “Irrigation control” to manually turn ON/OFF

the water timer and set the start time.

Tips: The connection delay will be around 0.5 to 1 seconds, please

do not repeatedly press the button.

3.2 Plan Setting

4. Sensor (Not including)

4.1. Sensors can be connected to monitor the soil moisture and

temperature, and then the data will be displayed as a graph. When

the soil moisture goes high, the water timer will stop watering

automatically once customer set the “stop watering moisture level”.

4.2. The water timer has its own water flow monitoring function and

users can check the daily water consumption and last water usage.

(The minimum monitoring water flow is 25L/H).

5. Tap-to-Run & Automation Irrigation

The Tap-to-Run and Automation planning systems are at “Smart”

selection which in the middle of the bottom panel.

There are many options shown on the page to select and a variety

of conditions can be added at the same time. In the device condition,

the basic options of the connecting devices are related to the data

from the WiFi timer and sensors.

The plan will be triggered when any single condition is met or all

conditions are met at the same time. All the data of current

conditions is automatically searched online by the App.

The figure shows that irrigation mode

watering 20 minutes. Start

time is 10 AM every Tuesday,

Wednesday and Thursday .

The figure shows: mist mode spray 30

seconds of every 5 minutes,

duration time is 4 hours (starting from

10:00 am and stop at 3:00 pm).

Click the Plan A/B/C to set daily irrigation schedule and rain delay

plan. The Irrigation schedule includes two mode: Irrigation mode

and Mist Mode. Different mode have different setting options and

both of them can be set with 12-hour or 24-hour.

On the Schedule page, there are Daily notices

of a week, Plan detail display board and rain

delay selections.

There are three plans that can be set in total.

Each plan has a unique represent color, which

will be shown under the day mark as a point

after turned on.

The setting detail of each plan is shown under

as a row and the on/off button is on the right

side.

The Rain delay (Watering Delay) can set with

24H, 48H and 72H.

3. Plans and Setting

3.1 Schedule overview

Shared the device and setting

to your home member who

has added on the family

group.

Different task could be set: Tap to Run, Enable or Disable

Automation, Send Notification, Delay and Device Option. When

the conditions are triggered, the task will be executed.

Basic Parameter of the device

Warranty & Warning

WARRANTY

1"BSP or 3/4" NH inlet

3/4’’outlet thread

Working pressure: 0.5 bar to 8 bar(10PSI-120PSI)

Max flow: 5L/min to 35L/min

Water proof: IP54

Working temperature: 0℃ to 50℃(37°F-122°F)

Battery life: over one year

WiFi timer power by 4 AA batteries, WiFi gateway power by AC

power

There are some existing Q&A to solve

problems. Tip: Please e-mail our

customer service or call us by phone to

get support if you need more help.

RainPoint App before connecting

to WiFi smart water timer.

Press the button to add a device.

After the gateway getting connected, click “Manager added devices”

to add WiFi water timers.

Insert 4xAA batteries to the water timer and press and hold the

button until the white LED light rapidly blink which means the device

is ready for connection. Select the choice of Wi-Fi water timer and

wait for connection. It will show “Device added successfully” once

WiFi water timer connects successfully.

Note: If it do not get paired in 20s, the LED indicator will light off and

stop connection.

Please press and hold the button for a few seconds again until the

LED indicator flashes rapidly to start connection.

If the LED indicator does not flash rapidly, please remove and

reinstall the batteries, then press and hold the button for 5 seconds.

After finishing the connection, all the paired devices will be displayed

on the page. The “Wi-Fi Socket” can set the gateway socket’s power

ON or OFF.Click the WiFi Water Timer and get into the main page

of the device.

The following information will be shown on the page: Temperature

unit selection, Last water usage, Soil Moisture and Temperature

(if already connected the sensor), Battery status, Mode and

Next irrigation time. The background color will turn red if the

moisture of soil is higher than setting.

At the bottom, there is an operating panel with several options:

Parameter, Irrigation control, Plan, Sensor and My.

Note：

If the water timer already paired with one gateway before, once it

has been re-insert batteries, the LED light will slowly blink, it means

the device is searching the gateway automatically.

After clicking the right top button, there is a basic information and

operation board with several different options: Device information,

Tap-to-Run and Automation and other basic functions and

services for the device.

Plug your WiFi gateway into an electrical socket. Open the APP and

click the “+” on the right top corner to add devices. Click the

“Irrigation Hub” and enter the WiFi password. Hold the button until

the blue LED light rapidly blink which means the device is ready for

connection.

TECHNICAL PARAMETER

WARNING

1. Under freezing temperatures, timers should be removed from the

faucet and stored indoors to avoid potential freezing damage.

2. Please clean filters regularly and replace if it is worn in order to

prolong life of timer.

The warranty aims for the problem of non-artificial damage and

provides a one-year warranty from the date of leaving the factory.

Tips and Warnings

5.1. Please make sure the smart phone is near the Wi-Fi water

timer when connecting or setting the watering plan. The best

range for operation or connection is within 60 meters in the

open area.

5.2. The watering timer will follow and perform the preset watering

schedule after application set successfully, even if the phone is

out off the best Connecting range.

5.3. LED light meaning:

a. White and rapidly blink: ready for pairing to smart phone;

1. Production Overview

2. Product Appearance

3. Website and QR Code

4. Main Functions

5. Illustrated Operating Instructions

6. Connection and Basic Information

7. Manual Operation

8. Plans and Setting

9. Sensor Connection

1 2 3

5 6 7 8 9 10 11

12 13 14 15 16 17 18

This kit includes one WiFi water timer and one WiFi gateway

One gateway can pair with maximum 4 WiFi water timers

433mHz RF communication with WiFi gateway and Water Timer

The WiFi gateway may also be used as WiFi timer socket

Set and check irrigation schedule through smart phone APP,

connecting with Wi-Fi

Available to work with soil moisture sensor

One Wi-Fi timer can pair one gateway and one Wi-Fi gateway

can pair one soil moisture sensor

Delay the irrigation schedule base on the data from soil sensor

Manually ON/OFF the water timer

Water flow meter function

With Irrigation mode and Mist mode options for watering

Low power indicator

With built-in filter

Water-leakage alert

Click the plus sign at the right top corner and schedule a smart plan.

There are some options to set up: Condition, Task and other

personal options.

b. White and slowly flash: searching the connecting gateway;

c. Red and blink every 6 seconds: low batteries power warning;

d. Red and breathing light blink: water leaking when turn off the

water timer;

e. Red when searching a sensor: does not find the sensor.

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced technician for help.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including

interference that my cause undesired operation.

MODIFICATION: Any changes or modifications not expressly

approved by the grantee of this device could void the user’s authority

to operate the device.

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment.

This transmitter must not be co-located or operating in conjunction

with any other antenna or transmitter.

This equipment should be installed and operated with minimum

distance 20cm between the radiator& your body.