Lupin_IOT.book Page 71 Monday, February 24, 2003 10:23 AM About Consumables 5 5.1 Available Consumables.................................................................... 72 5.2 EP Cartridge .................................................................................... 74 5.3 Fuser Unit ........................................................................................ 77 5.4 Transfer Roll Cartridge ..................................................................... 81 5.
Lupin_IOT.book Page 72 Monday, February 24, 2003 10:23 AM 5.1 Available Consumables The following consumables are available for this printer. To order these, contact our Printer Support Desk. EP cartridge The EP cartridge includes the toner and the photosensitive drum. If the toner in the EP cartridge is insufficient, the printout will become light and blurred. If it is time for replacement, replace with a new EP cartridge.
Lupin_IOT.book Page 73 Monday, February 24, 2003 10:23 AM 5.1 Available Consumables Regular replacement parts Regular replacement parts packaged together include the fuser unit, the transfer roll cartridge, and the feed roll. About 100,000 pages for a fuser unit and about 200,000 pages for a transfer roll cartridge and a feed roll can be printed. When these parts have reached this limit, replace them with new ones.
Lupin_IOT.book Page 74 Monday, February 24, 2003 10:23 AM 5.2 EP Cartridge This section explains about the EP cartridge. 5.2.1 Cautions on Handling the EP Cartridge When handling the EP cartridge, take note of the following points: Never throw an EP cartridge into an open flame. It can cause an explosion and you can get burnt. z About Consumables z z z z 5 z Do not subject it to direct sunlight or strong light.
Lupin_IOT.book Page 75 Monday, February 24, 2003 10:23 AM 5.2 EP Cartridge 2 Remove any paper in the center output tray. 3 Open the top cover. 4 Hold the EP cartridge by the grip and pull it out slowly. About Consumables Do not touch any parts inside the printer. 5 To prevent the toner from dirtying the floor, lay a piece of paper on the floor first before putting the EP cartridge down. 5 Take the new EP cartridge out of the box and shake it 7 to 8 times in the manner as shown in the diagram.
Lupin_IOT.book Page 76 Monday, February 24, 2003 10:23 AM 5.2 EP Cartridge 6 Place the EP cartridge on a flat surface and pull out the seal horizontally. z z 7 About Consumables 5 76 Hold the EP cartridge by the grip and insert it into the slot inside the printer. z z 8 When pulling out the seal, pull it out horizontally. The tape might break if it is pulled out diagonally. After the seal has been pulled out, do not shake or dump the EP cartridge. Do not touch any parts inside the printer.
Lupin_IOT.book Page 77 Monday, February 24, 2003 10:23 AM 5.3 Fuser Unit This section explains about the fuser unit. 5.3.1 Caution on Handling the Fuser Unit The fuser unit is included as one of the regular replacement parts. Before replacing the fuser unit, open the box of the regular replacement parts and get the new fuser unit ready. When handling the fuser unit, take note of the following points: z z Do not replace the fuser unit immediately after using the printer. You may get burnt.
Lupin_IOT.book Page 78 Monday, February 24, 2003 10:23 AM 5.3 Fuser Unit 5.3.2 Replacing the Fuser Unit Procedure About Consumables 1 Switch off the power of the printer and leave it for 30 minutes until the fuser unit cools down. 2 Remove any paper in the center output tray. 3 Lift the second lever from the top left corner of the back of the printer.
Lupin_IOT.book Page 79 Monday, February 24, 2003 10:23 AM 5.3 Fuser Unit 4 Open the rear cover. Do not touch any parts inside the printer. Lift the lever at both ends of the fuser unit to unlock it. 6 Pull down the 2 levers at the bottom of the fuser unit. 7 Remove the fuser unit slowly.
Lupin_IOT.book Page 80 Monday, February 24, 2003 10:23 AM 5.3 Fuser Unit Set the new fuser unit slowly. 9 Lift up the 2 levers at the bottom of the fuser unit and push down the levers at both ends of the fuser unit to lock it. About Consumables 8 5 80 10 Close the rear cover.
Lupin_IOT.book Page 81 Monday, February 24, 2003 10:23 AM 5.4 Transfer Roll Cartridge This section explains about the transfer roll cartridge. 5.4.1 Caution on Handling the Transfer Roll Cartridge The transfer roll cartridge is included as one of the regular replacement parts. Before replacing the transfer roll cartridge, open the box of the regular replacement parts and get the new transfer roll cartridge ready.
Lupin_IOT.book Page 82 Monday, February 24, 2003 10:23 AM 5.4 Transfer Roll Cartridge 5.4.2 Replacing the Transfer Roll Cartridge Procedure About Consumables 1 Switch off the power of the printer. 2 Remove any paper in the center output tray. 3 Open the top cover. 5 Do not touch any parts inside the printer.
Lupin_IOT.book Page 83 Monday, February 24, 2003 10:23 AM 5.4 Transfer Roll Cartridge 4 Hold the EP cartridge by the grip to pull it out slowly. To prevent the toner from dirtying the floor, lay a piece of paper on the floor before putting the EP cartridge down. 5 About Consumables Squeeze the levers on both ends of the transfer roll cartridge and pull it out slowly towards you. 5 6 Pick up the new transfer roll cartridge by the levers at both ends and slowly slot it in.
Lupin_IOT.book Page 84 Monday, February 24, 2003 10:23 AM 5.4 Transfer Roll Cartridge 7 Hold the EP cartridge by the grip and insert it into the slot inside the printer. z z 8 About Consumables 5 84 Do not touch any parts inside the printer. Ensure that the EP cartridge is firmly set. Close the top cover securely.
Lupin_IOT.book Page 85 Monday, February 24, 2003 10:23 AM 5.5 Feed Roll This section explains about the feed roll. 5.5.1 Caution on Handling the Feed Roll The feed roll is included as one of the regular replacement parts. Before replacing the feed roll, open the box of the regular replacement parts and get the new feed roll ready.
Lupin_IOT.book Page 86 Monday, February 24, 2003 10:23 AM 5.5 Feed Roll Feed roll Inside the printer (2 locations) Tray module (1 location) About Consumables Single-sheet bypass tray (1 location) Paper tray (1 location) Multiple-sheet bypass tray (1 location) 5 5.5.2 Replacing the Feed Roll The following procedure explains how to replace the feed roll of the paper tray. Follow the procedure here for replacing the feed roll of the tray module as well.
Lupin_IOT.book Page 87 Monday, February 24, 2003 10:23 AM 5.5 Feed Roll Feed roll at the paper tray Procedure 1 Pull the paper tray out of the printer. The feed roll on tray modules can be replaced without pulling out the paper tray. About Consumables 2 While pushing down the shaft of the feed roll as shown in the diagram (1), widen the tab of the feed roll to loosen it (2) and then slowly remove the feed roll from the shaft on the paper tray (3).
Lupin_IOT.book Page 88 Monday, February 24, 2003 10:23 AM 5.5 Feed Roll By aligning the small tabs on the feed roll with the slots of the shaft, push the feed roll completely in so that the tab fits into the slot. 4 Push the paper tray completely into the printer. About Consumables 5 Feed roll inside the printer Procedure 1 88 Remove any paper in the center output tray.
Lupin_IOT.book Page 89 Monday, February 24, 2003 10:23 AM 5.5 Feed Roll 2 Open the top cover. Do not touch any parts inside the printer. 3 About Consumables Hold the EP cartridge by the grip and pull it out slowly. To prevent the toner from dirtying the floor, lay a piece of paper on the floor first before putting the EP cartridge down.
Lupin_IOT.book Page 90 Monday, February 24, 2003 10:23 AM 5.5 Feed Roll By aligning the small tabs on the feed roll with the slots of the shaft, push the feed roll completely in so that the tab fits into the slot. 6 About Consumables 5 90 Hold the EP cartridge by the grip and insert it into the slot inside the printer. z z 7 Do not touch any parts inside the printer. Ensure that the EP cartridge is firmly set. Close the top cover securely.
Lupin_IOT.book Page 10 Monday, February 24, 2003 10:23 AM 1.4 Installation Procedure Installing the Printer 1.4.3 Installing the EP Cartridge When installing the EP cartridge, take note of the following points: Never throw an EP cartridge into an open flame. It can cause an explosion and you can get burnt. 1 z z z z z z Do not subject it to direct sunlight or strong light.
Lupin_IOT.book Page 11 Monday, February 24, 2003 10:23 AM 1.4 Installation Procedure Take the EP cartridge out of the box and shake it 7 to 8 times as shown in the diagram. Installing the Printer 2 1 3 Place the EP cartridge on a flat surface and pull the seal out horizontally. z z 4 Hold the EP cartridge by the grip and insert it into the slot inside the printer. z z 5 When pulling out the seal, pull it out horizontally. The tape might break if it is pulled out diagonally.