welder quesadilla sises | 3.2 Starting Up and Shutting Down the System This section explains how to start up and shut down the system. To start up the system, operations are required on the FDR D-EVE main unit and on the image processing unit. To shut down the entire system, operations are required only on the image processing unit. 3.21 Starting Up the System Press the ON side of the main switch of the power supply unit, if its power status LED is not lit.
3.2.2 Shutting Down the System Confirm that the equipment is not running. Touch the button at the upper right of the image processing unit's display, and then the button from the displayed menu. Touch the EX button in the displayed confirmation window. The image processing unit will shut down In a few minutes. if the control cabinet is Included in the system, the control cabinet will also turn off automatically. B Turn off the display as necessary. Turn off the radio graphic examination stand.
openness side emerge | 3.3 Routine Operations FDR D-EVE routine operations can be broadly divided into the following three steps. RIC Entering the Patient Information > (Ses page 3-13.) ¥ L1G Selecting the Anatomical Region and Exposure/Study Menu ®> (gee page 3-14.) << X-ray Exposure > (See page 3-16.) HINT Operations that are actually performed on the FDR D-EVE are only those described in Step 3 X-ray Exposure”, Other operations are performed on the image processing unit. © For details, see "DR-ID 300C\.
Entering the Patient Information The Patient Information Input Screen below is displayed on the image processing unit's display immediately after startup. Enter patient information it eras appropriately, and then touch the = button, é Not afl the rems of patient information need fo be input. Input any one of the items in order to proceed fo the next operation. é When the optional card reader is provided, patient information can be input by reading from a magnetic card.
merge Cassiopeia sises Selecting the Anatomical Region and Exposure/Study Menu a0 The Exposure Menu Selection Screen is displayed. Select an anatomical region from the display group list, and then select an exposure menu from the exposure menu list registered to the display group on the lower side, {More than one menu can be selected.) The selected exposure menus) is displayed In the selected exposure menu list on the right side of the screen.
torpedoes sel Edam X-ray Exposure When settings on the image processing unit have been completed, you can perform an exposure. (ZN cautions ) « Make sure to identify a patient against the name or birth date and then have him (her) take a proper positioning for exposure, « Make sure to confirm the exposure menu to be used and then have a patient take a proper positioning for exposure.
[2] X-ray exposure/image displaying & Make an exposure after confirming that Shot Ready {exposure ready status indicator) is lit green in the connected devices status of the image processing unit. Even if the flat panel sensor is subjected to X-ray radiation when Shot Ready is not green, X-ray radiation will be applied, however nu image will be acquired. Exposed images are transferred to the image processing unit. Find onward( OSH rm Touch ne JIE button at the lower right to complete the study.
chapter 4 Troubleshooting 4.1 When a Message Appears on the Image Processing Unit This section describes the warning dialog box and error messages. if an error which cannot be handled or the same error recurs frequently, contact a FUJI FILM dealer. if an error of unknown cause occurs, do not continue the operation and contact 8 FUJI FILM dealer. [1] If a warning dialog box appears if a communication error or an unexpected error has occurred, a warning dialog box pops up on the screen.
sme BUBOCHSIGNOIL [3] If an exposed image cannot be acquired & Do not remove the battery pack from the flat panel sensor until an exposed image is acquired. If removed, the image data and the exposure menu data used for the exposure will be ghost. If an exposed image cannot be acquired, the following error message may be displayed. If wireless communication Is disconnected during image reading, the following message dialog is displayed.
[4] If an error occurs on the image processing unit If an error occurs on the image processing unit, an error message box is displayed on the screen, In such a case, check error details, and then take an appropriate action. [51 If an error occurs on an output destination device If an error occurs on an output destination device, ® is displayed in the connected devices status. In such a case, operate as follows, Select ®B The "Output Device Status window” is displayed.
Bunoaysaanoul mie | 4.2 How to Cope with an Error... [1] When the system hangs up... If an inappropriate processing ie performed while this equipment is operating, the screen may freeze and the system may hang up (processing disabled). In that case, shut down the equipment forcibly according to the following procedure, and then restart it, if the screen freezes and & hang-up occurs, remove the keyboard and mouse and reconnect them.
[2] When the image processing unit is turned off due to an electrical outage ‘When the image processing unit is turned off due to an electrical outage, tee, fake the following actions according the condition when the power comes back on. = |f the power comes back on soon after an electrical outage Wait until the image processing unit restarts, When the image processing unit has restarted, shut down the image processing unit by following the normal procedure.
bugooysalqnol mm [71 If wireless communication is interrupted when using the flat panel sensor (DR-ID 601ST, DR-ID 602SE, DR-ID 611SE, DID 612SE and DR-ID 613SE) a if wireless communication is interrupted, an error message prompting re connection is displayed after 30 seconds. Select “Yes” to reconnect. a if wireless connection Is not established even after the selection is made, use the cable (wired connection) to transmit the image.
chapter 5 Daily Inspection and Maintenance | 5.1 Daily User Inspection and Maintenance During maintenance and inspection, strictly observe precautions contained in “Chapter 1 For Safe Operation” in this manual for you to use the FDR D-EVE under best conditions. 5.1.1 Daily Inspection (DR-ID 600) Inspection Before Use + Make sure that the equipment starts up normally. + Make sure that the equipment communicates with connected devices normally. » Make sure that the time displayed s correct. © See “3.
elfin asueNaIILN pue quondam Area 5.1.2 Periodical Inspection Inspection Every Three Mont| Using a vacuum cleaner, remove any dirt or dust accumulated in each unit of the equipment once vary three months. Clean then with a slightly moistened soft cloth and wipe off any moisture with a dry cloth. © See “2.2 Unit Names and the Functions’ (page 2-3). = DR-ID 600 DR-ID §00PU NO. Unit NO. Unit NO.
Appendix A Specifications | A.1 Specifications Specifications of the FDR D-EVE are shown below. A.1.1 Processing Capacity (DR-ID 600) um Routine processing (when the two-image output format is used in standard mode) {1} Exposure interval The exposure interval of the FDR D-EVE is at least § seconds. However, the interval varies depending on the region, the load to network communication, etc, A.1.
suoBeoysads v xipusddy mmm [Fig.
A1.3 Reduced Equivalent (DR-ID 600) Peak reduced equivalent on the front panel of the flat panel sensor: 0.5 mm Al A.1.4 Power Supply Conditions w DR-ID 600PU Rated voltage: 100-240V 10% ~ Input current : Frequency : 50-60Hz = DR-ID 600MC* Rated voltage: 115/230V ~ Input current © Frequency : 50-60Hz * Since the DR-ID BOOM is general-purpose electrical equipment, the electric rating above is an example. = AC adapter for cradle (optional) Rated voltage: 100-240V ~ Input current : Frequency © 47-63Hz A.1.
suoneooeds vxipuaddy mere = DR-ID 600MC {1} Operating Conditions Temperature 110°C 35°C Humidity I 20%RH 80%RH (no dew condensation) Atmospheric pressure : 706hPa 1080hPa {2} Non-operating Conditions {Environmental conditions under which power can he supplied) Temperature 140°C «BEC Humidity : 5%RH 95%RH (no dew condensation) Atmospheric pressure : 700hPa 1060hPa ® AC adapter for cradle (optional) {1) Operating Conditions Temperature 10°C 50°C Humidity : 0%RH 85%RH (no dew condensation) {2) Non-operating Co
| A.2 External View and Weight The external view and weight of the FDR D-EVE are shown below. é Specifications, dimensions and weight are subject to change for improvement without prior notice. A.2.1 DR-ID 600 = DR-ID 600PU 25H jhe gi ir ny Kali) (ORD 0058) 2.86.2) pane sensor 3.37.30 "Fiat panel sensor (DR-ID 6018E {for wired 384181) 3274) communication only) . pane] ser 15.40.61) 4.08.8) Fiat panel sensor (DR-ID 602SE (for wired 15.4061) 3.985) communication onion) — on peen sensor 1550061) 3607.
é ‘The effective area of the flat panel sensor is as shown in the figure below 2 § tees 432.0020) 10.75 RA = (088) 0.42) 2048 19.
® AC adapter for cardie EE iil 2 2 AC adapter 8502.2) BYE) pro SE cable for charging Unit: mm fin} ed, 1316.
suoneoywads yuppie Emmy | A.3 Characteristics {1) Micrometeorite Response Characteristics and Dynamic Range FDR D-EVE has a linear response against the exposure range where it can depict the clinical information. DR-ID 601ST and DR-ID 6025E (HOS-based) cover a dynamic range of 0.088 88. Gy at least at QUASAR. DR-D 811SE and DR-ID 8128E (Ce-based) cover a dynamic range of 0.088 44uGy at least at QUASAR. DR-D 6138E (Cal-based) covers a dynamic range of 0.
Appendix Z Precautions for Exposure | Z.1 Precautions for Exposure in AUTO MODE In AUTO MODE, stable image output can be obtained by means of the following. (1) Radiation field (2) EDR image data analysis (3) Detailed depiction of the cervical region However, problems may arise dus to differences in the multiple diaphragms or scattered rays of the X-ray equipment. For such problems, contact a FUJI FILM dealer and use other recording modes, such as SEMI-AUTO MODE or FIX MODE, 2.1.1.
swansong 40} ligneous Z xipusddy mms Z.1.2 Depiction of the Cervical Region 1 The radiation field must not include the whole head. Be sure fo secure transparent portions on both sides of the neck, {x} Use thé “Head” menu to include the whole head in the radiation field. 2 For exposure of the pharynx or larynx, be sure that the neck comes to the center of the radiation field so that the frontal and lateral orientations can be recognized appropriately.
Z.1.4 EDR Image Data Analysis 1 Image unevenness due to grid misalignment, X-ray beam misalignment, or metal objects may cause EDR image data analysis problems resulting in unstable density on the image. 2 if the target includes such materials as gypsum, denture, etc, stable density may not be obtained, because such materials make it difficult to analyze EDR image data. In such cases, use FIX MODE, 3 The EDR performs processing for the image area trimmed by the DR system.
unsound 40f SUCCESSION 2 Irrawaddy mpm Z.2 Precautions for Exposure in SEMI AUTO MODE These precautions are common to Semi |, 11, ill and HI). 1 Position the portion you need to display often in the center areas {10cm x 10cm{3.9 (Semi f), 7em x x 2.8 in.) (Semi Il), Sem x 5em{2.0 In. x 2.0 in.} (Semi HI} of the images trimmed by the DR system. Position the parson you need to display often in each of the Som » Semen in. » 2.0 in.
Z.3 Precautions for Exposure in SEMI-X MODE The user will select one of the nine areas of the Image trimmed by the DR system, on which SEMI AUTO MODE applies. (See the illustration below.) The same precautions as far SEMI-AUTO MODE apply. L CR Bem x Sem HAIR T (2.01n. x2.0in) LR ERE unsound J0) RESPONSIBLY Z XIPUIdUY mmo FOR D-EVE Operation Manuel B37NIGI473R.
swansong 10) ORNERINESS 2 Xipuoddy werewolves | Z.4 Precautions for Exposure in FIX MODE As reading conditions are fixed, exposure conditions must be controlled In the same way as for conventional X-ray exposure. The reading conditions (sensitivity and latitude) have been preset according to the relevant menu in FIX MODE. Select the exposure conditions which correspond to that menu accordingly.
Z.5 Precautions for the Automatic X-ray Detection Function 2.5.1 Precautions for Making an Exposure 1 When Shot Ready (exposure ready status indicator) in the connected devices status display field of the image processing unit is not lit green, the flat pane! sensor cannot detect X-rays automatically. Even if the indicator is nat lit green, radiation can be delivered but an image will not be output. Make sure that the indicator is lit green before making an exposure.
unsound joj sallowness 2 lupus meme 4 When an exposure menu Is registered and the system is ready for an exposure, the flat panel sensor enters X-ray detection mode. If an exposure is not made for a period of time while an exposure men is registered, the operating time of the flat panel sensor's battery pack may be reduced to half. In addition, the battery pack cannot be charged with an exposure menu registered, even if the flat panel sensor has a wired connection.
2.6 Precautions for Use in Wireless Communication Mode Care should be taken when the devices are used in wireless communication mode. Thoroughly read the following precautions in order to use the devices properly. m Icons Displayed on the image Processing Unit An icon indicating the status of wireless communication Is displayed in the connected devices status at the lower right of the Image processing unit display.
EET gainsay Jo) aforesaid 2 Irrawaddy | Z.7 Other Precautions 2.7.1 Precautions for Exposure of a Subject in Relatively Large Contrast 1 Exposures using a contrast medium may cause artifacts around it, 2 When exposing a subject with any metal objects implanted, artifacts may appear around them. 3 For exposures with objects of large X-ray absorption, such as lead characters and metals for measurement, artifacts may appear around them. Place such objects outside a subject. 2.7.
2.7.5 Precautions for Urgent Use When you start a study before completion of the calibration at the time of startup, the operation will be in Urgent Use Mode. At this time, "Urgent use is possible” appears In the “Output Device Status window" of the image processing unit. + There is no guarantee that the image taken in Urgent Use Mode can be used for diagnostic purposes. Vertical artifact could appear in the image, If the temperature difference is large from the previous shutdown of the system.
Appendix Use of Optional Items | 0.1 Optional Items Name Description Remote switch A switch cable used for temporarily disconnecting the power fo the flat panel sensor in order to connect/disconnect its connector while the system is in operation, Up to twa remote switches can be connected. Using this switch reduces the dime required for normal overemotional procedure, The switch is exclusively for DR-ID 6008E, © For the external view, see “0.2.1 Remote Switch” (page 0-3).
sway [condone Jo asn 0 Freddy mess Name Description Cradle A device used, when the flat panel sensor is moved to other X-ray room, to establish communication between the flat panel sensor and the power supply unit in the new location. The device is also used to keep the sensor upright when storing. © For the external view and precautions, see "0.6 Cradle” {page 0-8).
| 0.2 Using the Remote Switch 0.2.1 Remote Switch Operation button Remote switch fixture* (with double-sided tape} Remote switch * This metal fixture is used when the remote switch cannot be attached to a wall, etc. with the magnet on the back. The remote switch fixture is attached fo a wall, ete. with double-sided tape. 0.2.
| 0.3 Using the SE Storage Case SE storage case for 38 SE storage case for 43 {DR-ID 611SE) (DR-ID 6128E) (AN cautions b + Do not store the SE storage case in a location with the following conditions, « Where the SE storage case Is exposed to direct sunlight, « Where the temperature and humidity change dramatically, » Where there is excessive dust. » Where chemicals are stored. © Where the SE storage case may be exposed to water due to water leakage or ingress.
1 Battery holder L— [| {Battery holder ees pockets = 7 pockets insertion point SE storage case for 35 (DR-ID EDSEL) Nate that the storage method varies depending on the direction of the felt panel sensor (DR 600SE) cable, Set the fiat panel sensor with attention to the cable direction, and insert the connector into the insertion point. Make sure that the cable is not placed under the flat panel sensor.
swig) fondue Jo on © caddying | 0.4 Using the DAP Connector Cable The DAP connector cable is used for connecting a dose-area product (DAP) meter*! fo the power supply unit. This cable Is connected to a dose-area product meter via an R8232C insulator™. To connect a DAP meter, contact a FUJI FILM dealer. = Power supply unit RE232C insulator ° = DAP connector cable =1 A DAP meter of which FUJI FILM Corporation has confirmed the operational performance is Vacuum Standard of Evacuate Technician Gm.
I 0.5 Using the Retaining Bracket for MP Fixture {Anchor Contact a FUJI FILM dealer for installation of the Retaining bracket for MP.
sway (condone jo asn 0 xpusddy mores | 0.6 cardie a CAUTIONS J Cradle for 24 {ORD 6138E) » Handle the Cradle carefully. Do not hit or drop the Cradle or subject it to severe shock to avoid possible damage, Otherwise, personal injury may result, Consult a FULFILLMENT dealer for repair. the flat panel sensor inserted in the Cradle. ‘When carrying the Cradle, if you accidentally drop it, your foot may be injured. Do not make an exposure when the flat panel sensor is inserted in the Cradle.
| 0.7 AC adapter for cradle SE cable for charging AC adapter for cradle (AN cautions) « Use a grounded hospital grade power cable with 3 pins, Ensure that the length of the cable is 3 m (9.8 ft) or less. Do not use a power distribution board. Instead, plug the cable directly into the power outlet, Not doing so may cause fire or electric shock. Never disassemble or modify the AC adapter for cradle or supplied cable.
pm swot Condone jo on © caddying a0 insert the power cable into the power outlet, : B Remove the flat panel sensor from the cradle. J : Wireless communications will resume after several If the relay connector is not secured in : seconds. place, insert it until it locks with a click. Aa After checking that the exposure menu has not been registered by the image processing unit, insert the flat panel sensor into the cradle (sold separately) or Cradle for 24 {sold separately).
Maintenance and Inspection Maintenance and Inspection Items Assigned to Specified Dealer For periodical inspection of the equipment and necessary arrangements, consult our official dealer or local representative, Periodical Maintenance Marks sure that the periodical maintenance and inspection assigned to our official dealer are performed as specified.